INTRODUCTION
Man is an ambitious creator. He has conquered the world of science and has reached to this 21ST century. In pre-cuts of perfection. He has cared much for automation and product quality which is directly co related to electronics.
In this fact developing society, electronic has come to stay as the most important branch of Engineering. Electronic devices are being used in almost all the industries for quality control and automation. They have become a fast replacement of present workers army which is engage ....etc

[:=Read Full Message Here=:]

73. RF CONTROL OF INDUCTION MOTORS AND OTHER INDUSTRIAL LOADS
# can I know more information about that Topic?
# and where can this project apply? :idea::D ....etc

[:=Read Full Message Here=:]

In this seminar the cadmium™s effect on anti-oxidative enzymes in tomato (Lycopersicon esculentum) plants was evaluated. Plants treated with increasingly CdCl2concentrations (0, 20, 40, 80, 100 and 200 M respectively) were grown in a basic nutrient solution for 7 days. APX (Ascorbate Peroxidase) and GPX (Guaïgol Peroxidase) activities showed to increase below 100 M concentration after treatment. In excessive concentration however, more than determined level, a significant decrease in the enzymes activities was determined. The incr ....etc

[:=Read Full Message Here=:]

can u give any details about DSP based speed estimation of single phase induction motors ....etc

[:=Read Full Message Here=:]

Hi am amit i would like to get details on safety induction training ppt in hindi ....etc

[:=Read Full Message Here=:]

Abstract
Efficiency and scalability are fundamental issues concerning data mining in large databases. Although classification has been studied extensively, few of the known methods take serious consideration of efficient induction in large databases and the analysis of data at multiple abstraction levels. The paper addresses the efficiency and scalability issues by proposing a data classification method which integrates attribute oriented induction, relevance analysis, and the induction of decision trees. Such an integration leads to efficient ....etc

[:=Read Full Message Here=:]

ANALYSIS OF RESIDUAL STRESSES IN MAIN CRANKSHAFT BEARINGS AFTER INDUCTION SURFACE HARDENING AND FINISH GRINDING


INDUCTION SURFACE HARDENING

ADVANTAGES

¢ Short Heat Treatment Times

¢ Good Repeatability

¢ Hardened Layer Quality

¢ Small or Negligible Subsequent Distortion

¢ Minimum Subsequent Product Surface Oxidation

¢ Good Possibilities for Automation

SURFACE INTEGRITY AND ITS LEVELS

Scientific discipline providing an integral assessment of the surface and surface layers
Measurement of Roughness ....etc

[:=Read Full Message Here=:]

INDUCTION AND TRAINING AT DC(B)L



LEARNING DURING TRAINING

Induction at RTC
June 9th to July 24th
Basic knowledge about cement manufacturing process
Introduction to various departmental roles
Plant familiarization
At National Council for Cement and Building Materials (NCCBM)
July 27th to September 25th
Process based study on cement and materials

Responsibilities handled

KHD stoppage -OCTOBER ‘09
LT Motor overhauling
materials arrangement and coordination
Re ....etc

[:=Read Full Message Here=:]

ENHANCED PERFORMANCE OF A DOUBLY FED
WIND-POWER INDUCTION GENERATOR AT WIND-
RANGE BOUNDARIES
ABSTRACT
The doubly fed induction generator (DFIG) is one of the largest generators used
with MW-class wind turbines. This paper focuses on the weak performance areas
of grid-connected DFIG-based wind turbines. Basically, the DFIG performance at
low wind speeds, close to the cut in speed, and around the full rating operation (in
the vicinity of rated wind speed) is investigated. For low wind speed region, the
c ....etc

[:=Read Full Message Here=:]

Summary
The main objectives of this paper are to perform fault analysis on an induction motor using both experiments and simulation, and to study failure identification techniques applied for condition monitoring of the motor and finally to design an On-line condition monitoring system with fuzzy logic controller using LabView. The work in this paper was divided into two phases. The phase one was concerned with the modeling of three-phase induction motor in three phase reference frame using Matlab/Simulink and designing an i ....etc

[:=Read Full Message Here=:]