. Automatic voltage regulation of alternator used in UKAI PP ....etc

[:=Read Full Message Here=:]

AIM
To conduct the slip test on three phase alternator and predetermination the regulation through vector diagrams
APPARATUS REQUIRED
PRECAUTION
1. The Motor field Rheostat should be kept in minimum resistance position.
2. The Alternator field should be kept open throughout the experiment.
3. The direction of rotation due to prime mover and due to the Alternator run as the motor should be same.
4. Initially all the switches are kept open
PROCEDURE
1. The name plate details of the motor an ....etc

[:=Read Full Message Here=:]

Based on closed form expressions for the power frequency voltages and currents in a typical distribution network, the voltage regulation VR at any time point during the day could be evaluated. It will depend primarily on the network configuration, the daily load curve, the load density and its power factor as well as level of the reactive power compensation.

The computed at a certain time?t? can give a useful indicator for the voltage constancy over the network at that time point. The concept of ?Global Voltage Regulation? is introduced. Th ....etc

[:=Read Full Message Here=:]

THEORY:
The regulation of a 3-phase alternator may be predetermined by conducting the Open Circuit (OC) and the Sort Circuit (SC) tests. The methods employed for determination of regulation are EMF or synchronous impedance method, MMF or Ampere Turns method and the ZPF or Potier triangle method. In this experiment, the EMF and MMF methods are used. The OC and SC graphs are plotted from the two tests. The synchronous impedance is found from the OC test. The regulation is then determined at different power factors by ....etc

[:=Read Full Message Here=:]

AIM
To conduct OC, SC and ZPF test on the three phase alternator and to predetermine the regulation of 3 phase alternator by EMF method, MMF method, & ZPF method also to verify by vector diagram.
APPARATUS REQUIRED
PRECAUTION
1. The motor field rheostat should be kept in the minimum resistance position.
2. The alternator field potential divider should be in the minimum voltage position.
3. Initially all switches are in open position.
PROCEDURE
A. OC.Test
1. Note down the name ....etc

[:=Read Full Message Here=:]

AIM:
To predetermine the regulation of three phase alternator by Potier and ASA methods and also to draw the vector diagrams.
FORMULAE USED:
Percentage regulation = Eo – Vrated x 100 (For both POTIER & ASA methods)
Vrated
PRECAUTION:
(i) The motor field rheostat should be kept in the minimum resistance position.
(ii) The Alternator field potential divider should be in the position of minimum potential.
(iii) Ini ....etc

[:=Read Full Message Here=:]

related information of Automatic voltage regulation of alternator ....etc

[:=Read Full Message Here=:]

Automatic Voltage regulation technology
Introduction
Excitation system
Automatic voltage regulator
1.Excitation system
What is excitation system ?
Perpose of excitation system.
Type of excitation system
Conventional DC system.
Brushless excitation system.
AC excitation system with noncontrolled diode rectifier.
Alternative excitation system with stationary controlled thyristos rectifier.
Voltage source controlled exciter.
Compound source controlled exciter.
1.Conventional DC system
....etc

[:=Read Full Message Here=:]

presented by:
J.Chaithanya Bharathi
A.L.Harika
P.Divya Sree


ABSTRACT
The performance of any machine can be analyzed with reference to parameters like power factor, total harmonic distortion, voltage regulation, etc. These parameters alter when a machine is subjected to different loads. Depending on the load connected to the system, the voltage and current waveforms are varied. Due to the effect of harmonics, distortion of waveforms from sinusoidal to non sinusoidal is c ....etc

[:=Read Full Message Here=:]

Efficient Voltage Regulation for Stand Alone Photovoltaic Cell using PI Controller for AC Voltage Application
Abstract— This paper focuses on the renewable energy system PV (Photo Voltaic) Cell in stand alone model. The system consisting of solar PV cell, DC-DC Boost converter, and inverter coupled to the load system. An 18V photovoltaic cell and a DC-DC boost converter is designed for the purpose of boosting the PV cell output voltage. The advantage of using the proposed DC-DC converters are only one sensor is required, high ....etc

[:=Read Full Message Here=:]