I want information related this topic...selection of project, conclusions, methodology, observation, objective, importance ....etc

[:=Read Full Message Here=:]

i would like to get details on is the earth turning into a dumping ground pdf ....etc

[:=Read Full Message Here=:]

181/2014
Maximum : 100 marks
Time : 1 hour and 15 minutes

1. An oily floor should be cleaned by:
(A) Cotton waste
(B)Putting water
(C ) Putting saw dust or sand
(D)Spraying carbon dioxide '

2.The file used for trimming the rough edges of soft metal casting:
(A) Bastard file
(B)Rough file
(C ) Rasp file
(D)Second cut file

3.The cutting angle for chipping mild steel is:
(A) 65°
(B)45°
(C ) 55°
(D)60°

4.The box nut of bench vice is made of:
(A) Mild steel
(B)Gun metal
(C ) Phospharous bronze
( ....etc

[:=Read Full Message Here=:]

pls I want PDF of is earth turning into dumping ground??? ....etc

[:=Read Full Message Here=:]

Please give me PDF of is earth turning into dumping ground ....etc

[:=Read Full Message Here=:]

ABSTRACT
Despite all the attempts of modern information technology to supplant paper by sophisticated electronic devices, paper is still omnipresent in virtually any office environment. Today, paper and computer are coexisting side by side without interacting with each other, both having their specific advantages. This seminar presents a concept for bridging the gap between computer and paper by combining the advantages of both electronic and paper world, the ease of use provided by the classic pen-and-paper interface is unsurpassed. Exce ....etc

[:=Read Full Message Here=:]

163/2016
Maximum : 100 marks
Time : 1 hour and 15 minutes

1. The Lathe Centres are provided with standard taper known as :
(A) Brown and sharp taper
(B)Morse taper
(C ) Seller’s taper
(D)Brown taper

2.The chuck used for setting up of heavy and irregular shaped work should be ?
(A) Four jaw independent chuck
(B)Three jaw universal chuck
(C ) Magnetic chuck
(D)Collet chuck

3.The Chamfaring is an essential operation after :
(A) Boring
(B)Rough turning
(C ) Knurling
(D)Thread cutting

4.Least count of ....etc

[:=Read Full Message Here=:]

168/2014
Maximum : 100 marks
Time : 1 hour and 15 minutes

1.Ceramic cutting tools are made from :
(A)Tungsten powder
(B) Aluminium oxide powder
(C ) Titanium oxide powder
(D) Iron carbide powder

2.In a vernier micrometer 0.001” is divided into 10 divisions in vernier scale. The 10 vernier scale divisions is equal to how many thimble divisions for getting 0.0001” accuracy?
(A)9 divisions
(B)20 divisions
(C )10 divisions
(D)24 divisions

3.The cutting edge becomes stronger where the cuttingtool is provid ....etc

[:=Read Full Message Here=:]

i would like to get more details abt ths topic...... plzzz.... ....etc

[:=Read Full Message Here=:]

1.Fillet gauges are available in standard radii from
A) 1.55 mm to 12 mm
B) 2.5 mm to 3.5 mm
C) 1 mm to 2 mm
D) 3.5 mm to 4 mm

2.The cutting edges need to be honed with special grinding stricks called
A) Oxide grinding wheel
B) Aluminium Oxide wheel
C) Honing strick
D) Carbide grinding strick

3.Form tools have a much longer cutting edge than
A) Special turning tool
B) Ordinary turning tool
C) Facing tool
D) Turning tool

4.This method of marking is used on
A) Datum line method 
B) Centre line metho ....etc

[:=Read Full Message Here=:]