17-04-2017, 02:47 PM
TRADESMAN - TURNING - TECHNICAL EDUCATION.pdf (Size: 1.26 MB / Downloads: 2)
163/2016
Maximum : 100 marks
Time : 1 hour and 15 minutes
1. The Lathe Centres are provided with standard taper known as :
(A) Brown and sharp taper
(B)Morse taper
(C ) Seller’s taper
(D)Brown taper
2.The chuck used for setting up of heavy and irregular shaped work should be ?
(A) Four jaw independent chuck
(B)Three jaw universal chuck
(C ) Magnetic chuck
(D)Collet chuck
3.The Chamfaring is an essential operation after :
(A) Boring
(B)Rough turning
(C ) Knurling
(D)Thread cutting
4.Least count of steel rule is :
(A).25 mm
(B).1 mm
(C ).5 mm
(D).2 mm
5.The heat treatment process for softening hardened steel is :
(A) Carburising
(B)Normalising
(C ) Annealing
(D)Tempering
.Steel containing 0.8 to 1.5% carbon is known as :
(A) Mild Steel
(B)High Carbon Steel
(C ) Dead Mild Steel
(D)Medium Carbon
7.A lathe with four steps on the cone pulley and with back gears will have :
(A) Four direct speeds
(B)Four indirect speeds
(C ) Four direct and four indirect speeds
(D)Eight indirect speeds
8.Least count of vernier caliper metric is :
(A) 0.02 mm
(B)0.01 mm
(C ) 0.00001 mm
(D)0.0004 mm
9.For turning internal tapers, the suitable method is:
(A)by setting over the tail stock
(B)by a form tool
(C )by a taper turning attachment method
(D)none
10. The percentage of carbon in cast iron varies from :
(A)0.1 to 0.5
(B)0.5 to 1
(C )1.7 to 4.5
(D)0.2 to 3
11.The correct order of increasing hot hardness of cuttingtool materials:
(A)Diamond, Carbide, High speed steel
(B)Carbide, Diamond, High speed steel
(C )High speed, Carbide, Diamond
(D)None
12.Americannational standard thread is :
(A)58°
(B)65°
(C )AT
(D)60°
13.A single point thread cutting tool should ideally have :
(A)Point angle
(B)Zero rake angle
(C )Positive rake angle
(D)Negative rake angle
14.The alloy, mainly used for corrosion resistance instainless is
(A)Manganese
(B)Silicon
(C )Carbon
(D)Chromium
15.The heat treatment process used for casting is:
(A)Normalising
(B)Annealing
(C )Tempering
(D)Carburising
16.The taper on the lathe spindle is :
(A)2 to 20
(B)3 to 20
(C )1 in 20
(D)4 in 20
17. Tumbler gears in lathe are used to :
(A)Cut gears
(B)Cut taper
(C )Reduce the spindle speed
(D)Give desired direction of movement to the lathe carriage
18. In which, Coolant is used for Aluminium turning :
(A) Dry
(B)Kerosene
(C ) Soda water
(D)Lard oil
19.The cutting speed for drilling copper with high speed;steel drill varies
from
(A) 18 to 30 m/min
(B)8 to 15 m/min
(C ) 30 to 45 m/min
(D)10 to 30 m/min
20.The blade of power saw is made of:
(A) Cast Iron
(B)Aluminium
(C ) High speed steel
(D)High carbon steel
21.British association thread angles is :
(A) 3 T
(B)27°
(C ) 57
(D)471/2°
22.The material commonly used for machine bodies is :
(A) Cast Iron
(B)Aluminium
(C ) Brass
(D)Mild Steel
23.Acme screw thread angles is :
(A) 49°
(B)29°
(C ) 39u
(B)19°
24.Which coolant is used for mild steel for Lapping9
(A) Kerosene
(B)Turpentine
(C ) Lard oil
(D)Dry
25.Which of the following material have maximummalleability?
(A) Soft steel
(B)Copper
(C ) Cast iron
(D)Lead
26. Angle of B.S.W. thread is :
(A) 50°
(B)
(C ) 55°
(D)
27. Which of the following is a mesomorphous material?
(A) Silver
(B)
(C ) Brass
(D)
28.High speed steel temperature is :
(A) 900° C
(B)
(C ) 300°
(D)
29.What is cutting Feed’?
(A) Tool advance for 2 minute
(B)
(C ) Tool advance for 4 minute
(D)
30.What is lip angle?
(A) 20° to 40°
(B) 30° to 50°
(C ) 60° to 80°
(D) 80° to 120°
31.An Alloy of copper, tin and zinc is known as :
(A) Brass
(B) Gun metal
(C ) Bronze
(D) Cast iron
32.What is cutting speed?
(A)Tool advance for work in one minute
(B)Tool advance for 3 minute
(C )Tool advance for 2 minute
(D)Tool advance for one rotation
53°
600
Lead
Mica
1000
2600°
Tool advance for 3 minute Tool advance for one rotation
33.Discontinuous chips are formed during machining of:
(A)Brittle metals
(B)Hard metals
(C )Soft metals
(D)Hard and soft metals
34.The angle made by the face of the tool and the plane parallel to the base
of cutting tool is called:
(A) Cutting angle
(B)Lip angle
(C ) Rake angle
(D)Clearance angle
35.The lower critical point for all steel is :
(A) 623° C
(B)723° C .
(C ) 913° C
(D)523° C
36.Combination central drill angle is :
(A) 55°
(B) 118°
(C ) 29°
(D) 60°
37.Carbide tipped tools usually have :
(A) Any rake angle
(B)Positive rake angle
(C ) Negative rake angle
(D)No rake angle
38.Hard and tough materials like cast iron should be turned at:
(A)Slow speed
(B) High speed
(C )Any speed
(D) Very high speed
39.Ceramic tools are fixed to tool body by :
(A)soldering
(B) brazing
(C ) welding
(D) clamping
40.For machining a mild steel work piece using carbide tool, the maximum
material will be removed at a temperature of:
(A) 200° C
(B)300“ C
(C ) 175° C
(D)1000 c
41.Lathe centrers angles is :
(A) 55°
(B) 65°
(C ) 60°
(D) 700
42.Crater wear is predominant in :
(A) Tungsten carbide tools
(B)Carbon tool steels
(C ) High speed steel
(D)Carbon tip tool
43. Which type of tools are used on Lathe shapper and planer?
(A) Two point cutting tool
(B)Three point cutting tool
(C ) Multi point cutting tool
(D)Single point cutting tool
44.Twist drill standered cutting angle is :
(A)90°
(B)55°
(C )1180
(D)60°
45.The swing diameter over the bed isthe height of the centre measured
bed of the lathe.
(A) Equal to
(B)Twice
(C ) Thrice
(D)One half
46.The diamond tool material at temperature upto:
(A) 16500C
(B) 1300"C
(C ) 1200“C
(D)1400" C
47.The chuck preferred for quick setting and accurate centering of a job is:
(A) Four jaw independent chuck
(B)Collect chuck
(C ) Magnetic chuck
(D)Three jaw universal chuck
48.The cutting fluid mostly used for machining steelis:
(A) Water
(B)Dry
(C ) Heavy oil
(D)Soluble oil
49.The point angle of a drill, for drilling stainless steel is
(A) 90°
(B)118°
(C ) 135°
(D)150°
50.The steel widely used for making precision measuringinstruments is:
(A) Nickel steel
(B)Nickel — Chromium steel
(C ) High speed steel
(D)High carbon steel
51.With the same tool life, the maximum material per minute is removed by :
(A) Increasing the feed rate
(B)Decreasing the cutting speed
(C ) Increasing the cutting speed
(D)Increasing the depth of cut
52.The lead screw of a lathe has threads.
(A)single start
(C )V. thread
(B)double start
(D)multi-start
53.The least count of the vernier bevel protractor is :
(A)6 minute
(B) 7 minute
(C ) 8 minute
(D) 5 minute
54.Screw pitch gauge is mainly used to check :
(A)Boring
(B)Used to check external and internal threads
(C )Knurling
(D)Under cutting
55.An operation of embossing a diamond shaped pattern on the surface of work
piece, is known
(A) Threading
(B) Grooving
(C ) Knurling
(D) Step cutting
56.Drilling is an example of:
(A) multi cutting
(B)oblique cutting
(C ) simple start cutting
(D)orthogonal cutting
57.A sine bar is specified by its :
(A) width
(B)length
(C ) diameter
(D)step
58.What material is used to make scriber?
(A) Carbon tool steel
(B)High carbon tool st
(C ) High speed steel
(D)Mild steel
59.Who is the founder of fundamental principle of screw cutting lathe?
(A) Henry Richards
(B)Samuel
(C ) Henrimanslae
(D)Wilson de Paul
60. What is the angle of worm thread?
(A)49°
(B) 55°
(C ) 47°
(D) 29°
61. Formula for finding R.P.M. in British system :
(A)Cutting speed x 12
(B)Cutting speed x 24 DL
(C )Cutting speed x 18 D
(D)Cutting speed x 20 x D
62.The operation of making a cone - shaped enlargement of the end of a hole
is known as :
(A)counter - boring
(B) spot facing
(C ) boring
(D) counter - sinking
63.Trepanning is an operation of:
(A)Making a cone - shaped enlargement of the end of a hole
(B)Producing a hole by removing metal along the circumference of a hollow
cutting tool
(C )Smoothing and squaring the surface around a hole
(D)Finishing a small diameter hole
64.The washer is generally specified by its :
(A)Outer diameter
(B)Thickness
(C )Mean diameter
(D)Hole diameter
65.Low helix angle drills are preferred for drilling holes in :
(A)Copper
(B)Aluminium
(C )Plastics
(D)Cast steel
66.A tool used to with draw a drill from the sleeve is called:
(A)Drill puller
(B)Brill drawer
(C )Drill rotator
(D)Drift
67.The enlarging of an existing circular hole with a rotating single point
tool is called:
(A)boring
(B)reaming
(C )drilling
(D)knurling
68.The grinding of long, slender shafts or bars is usually done by :
(A)In feedgrinding
(B)End feed grinding
(C )Through feed grinding
(D)Speed grinding
69.The cutting fluid mostly used for machining alloy steels is :
(A)water
(B)sulphurised mineral oil
(C )solubleoil
(D)dry
70.The trade name of a non ferrous cast alloy composed of cobalt, chromium
and tungsten is called:
(A) stellite
(B)diamond
(C ) cast iron
(D)ceramic
71.Tool signature consists of------
(A) Six
(C ) Seven
(B)Four
(D) Eight
72.A grinding wheel is said to be of elements if it holds the Abrasive grains
more securely.
(A) Soft grade
(B)Hard grade
(C ) High grade
(D) Medium grade
73.The process of changing the shape of grinding wheel as it becomes worn due
to breaking away of the abrasive and bond, is called :
(A)Turning
(B)Facing
(C )Boring
(D)Dressing
74.Chip breakers are used to :
(A)increase tool life
(B)to minimise heat generation
(C )remove chips from bed
(D)break the chips into shortsegments
75.The lathe spindles are usually made hollow and provided with :
(A)Internal taper
(B)No taper
(C )External taper
(D)Step taper
76.In order to achieve a specific surface finish in single point turning, the
most important factor to be controlled is :
(A) feed
(B) cutting speed
(C ) under cutting
(D) depth of cut
77.A Hacksaw blade is specified by its :
(A) Width
(B) Number of teeth
(C ) Length
(D) Material
78.The instrument used to measure external and internal diameter of shafts,
thickness and depth of holes is :
(A) Out side caliper
(B)Vernier caliper
(C ) Inside caliper
(D)Inside micrometer
79.According to Indian standards, the total number of tolerance grades are :
(A) 18
(B) 14
(C ) 13
(D) 8
80.Formula for finding cutting speed in metric system :
(A)xDx RPM 100
(B)kDxRPM 2000
(C )xDxRPM 1000
(D)nDxRPM 1200
81.type of sand is produced after the mechanical disintegration process.
(A) Mountain soil
(B) Red soil
(C ) Black soil
(D) Arid soil
82.Gersoppa waterfalls originated from :
(A) Narmada
(B) Mahanadi
(C ) Tapti
(D) Sharavati
83.Pannadiamond belt situated at:
(A) Gujarat
(B) Rajasthan
(C ) Madhya Pradesh
(D) Bihar
85.would taken for?
(A)10 hours 24 minutes
(C )13 hours 30 minutes
(B)11 hours 26 minutes
(D)12 hours 26 minutes
86.Industrial Credit and Investment Corporation
(A)1953
(B)1955
(C )1954
(D)1951
86.The National Bank for agriculture and recommendation of:
(A) B. Sivaraman Committee
(B) Gopalram Committee
(C ) Chandra Sekharan Committee
(D) Kamath Committee
87.Which one of the following newspaper that was started by Rajaram Mohan
Roy?
(A)Bengal Gazzette
(B)Al-Hilal
(C )Mirat-Ul-Akbar
(D)The Statesman
88.Universities of Calcutta, Bombay and Madras started by :
(A)Lord Wellington
(B)Lord Irwin
(C )Lord Canning
(D)Lord Ripon
89.In 1928 all parties conference held at Calcutta which has approved?
(A)CR Formula
(B)Nehru Report
(C )Swedeshi Movement
(D)Non-CooperationMovement
90.Mahatma Gandhi called Tagore as :
(A)Guro
(B)Guru Dev
(C )Rana
(D)Pratap
91.-----------is one of the rain shadow region in Kerala.
(A) Ponmudi
(B) Athirappilli
(C ) Marayur
(D) Pookkod
92.Who is the author of ‘Adwaitha Chintha Paddhathi’?
(A)Dr. Palppu
(B)Chattambi Swamikal
(C )Sree Narayana Guru
(D)Mannath Padmanabhan
93. V.T. Bhattathirippad wrote the book :
(A)Kunthalatha
(B)Rajani Rangam
(C )Ulakka
(D)Premamrutham
94. Who led Ezhava Memorial?
(A)Kumaranasan
(B)Dr. P. Palppu .
(C )Vagbhatananda
(D)Pandit Karuppan
95. In 1910 which social reformer nominated to SreeMoolam Praja Sabha?
(A)Thycaud Ayya
(B)Ayya Vaikundar
(C )Ayyankali
(D)Pandit Karuppan
96. The founder of the newspaper Swadeshabhimani is:
(A)Swadeshabhimani Ramakrishna Pillai
(B)Vakkom Muhammed Abdul Moulavi
(C )Mannath Padmanabhan
(D)Herman Gundart
97.In 2016 COPA America Football Tournament, who won the Golden Boot Award?
(A)Lionel Messi
(B)Christiano Ronaldo
(C )Edurado Vargas
(D)Lui Suaras.
98.The name Safari Karmachari Andolan associated with:
(A)Medhapatkar
(B)Kailash Sathayarthi
(C )Beswada Wilson
(D)Dr. Binayak Sen
99.Who has been newly appointed as Chairman of KeralaChalachithra Academy?
(A)Kamal
(B)Lenin Rajendran
(C )Priyadarsan
(D)Rajeev Nath
100.2016 NSGplenary held at:
(A)China
(B)Brazil
(C )South Korea
(D)Japan