Please give a suitable and easy idea to make physics project on photodiode for class 12 ....etc

[:=Read Full Message Here=:]

HIGH SPEED MACHINING
ABSTRACT
Over the past 60 years, high speed machining (HSM) has been applied to a wide range of metallic and non-metallic work piece materials including the production of components with specific topography requirements and machining of materials with hardness of 50 HRC and above.
With most steel components hardened to approximately 32-42 HRC, machining operations currently include:
Rough machining and semi-finishing of the material
Heat treatment to ach ....etc

[:=Read Full Message Here=:]

please send me a powerpoint presentation on photodiode
....etc

[:=Read Full Message Here=:]

a full report on seminar topic optical detectors
with presentation ie ppt
with introduction,working principle,construction ,advantages ,disadvantages ,conclusion references
etc........
provide me with the above mentioned clauses ....etc

[:=Read Full Message Here=:]

An Integrated Silicon Carbide (SiC) Based Single Phase Rectifier with Power Factor Correction



I. INTRODUCTION
Power supplies are one of the most crucial building
blocks of a modern society, converting high-voltage AC
into low-voltage DC for use in electronic circuitry in office
equipment, telecommunication, and consumer electronics.
Over 2.5 billion AC/DC power supplies are currently in use
in the United States alone, about 6 to 10 billion are in use
....etc

[:=Read Full Message Here=:]

A MICROFORCE AND NANOFORCE BIOMICROSCOPE DEVICE FOR IN VITRO MECHANOTRANSDUCTION INVESTIGATION
Presented By:
Jins George
S7 AEI
College Of Engineering, Trivandrum




CONTENTS
Introduction
Motivations of this Work
Block Diagram of the FBM Device
Description of the FBM Device
Cantilever Spring Constant Calibration
In Vitro Mechanical Characterization Experiments
Conclusion
References

INTRODUCTION
Mechanotransduction
Characterization of Cell Mec ....etc

[:=Read Full Message Here=:]

MICROCONTROLLER:
In this project we use 89S52 controller as a main processor to done all the activity of this project. 89S52 is a 40 pin member of the 8051 family.
MOTOR’S:
In this project we use two slow speed dc motor to run the vehicle on the track. Along with vehicle movement we use two another motor for arm movement .In this project we use four slow speed motor. Working voltage of these motor’s is 6- 9 volt dc. These type of motor’s are slow speed gear motor. These motor’s cons ....etc

[:=Read Full Message Here=:]

Silicon Carbide Photodiode Flame Temperature Sensors in an Active Combustion Pattern Factor Control System


Introduction
The combustion pattern factor in a gas turbine is a measurement
of the difference between the peak and average temperature at the
turbine inlet.
where Tpeak is the measured peak temperature at the combustor
exit and Tavg is the average of the measured temperatures.
The objective of active pattern factor control APFC is ....etc

[:=Read Full Message Here=:]

METALLURGICAL CHANGES IN STEELS DUE TO CRYOGENIC PROCESSING & ITS APPLICATIONS

Metallurgical changes in steels due to cryogenic
processing & its applications

Abstract:
Cryogenic processing is a supplementary process to conventional heat treatment process in steels. It is an inexpensive one time permanent treatment affecting the entire section of the component unlike coatings. Though the benefits have been reported widely, there are issues debated upon, in respect of the treatment parameters, extent of benefits ex ....etc

[:=Read Full Message Here=:]

Please give some viva voce questions together with answers based on photodiode as a switch ....etc

[:=Read Full Message Here=:]

Today 208th bangasree super result in west bengal , kolkata ....etc

[:=Read Full Message Here=:]

project report of infrared security alarm ....etc

[:=Read Full Message Here=:]

Paper Presentation On Bionic Eyes - Hope for the blind!
Abstract
Technology has done wonders for the mankind. We have seen prosthetics that helped overcome handicaps. Bio medical engineers play a vital role in shaping the course of these prosthetics. Now it is the turn of Artificial Vision through Bionic Eyes.
Chips-designed specifically to imitate the characteristics of the damaged retina, and the cones and rods of the organ of sight are implanted with a microsurgery.
Whether it be Bio medical, Computer, Electri ....etc

[:=Read Full Message Here=:]

i need matlab code for I-V and quantom efficiency of a PIN photo diode ....etc

[:=Read Full Message Here=:]

Metal matrix composite

A metal matrix composite (MMC) is composite material with at least two constituent parts, one being a metal. The other material may be a different metal or another material, such as a ceramic or organic compound. When at least three materials are present, it is called a hybrid composite. An MMC is complementary to a cermet.Contents
1 Composition
1.1 Matrix
1.2 Reinforcement
2 Manufacturing and forming methods
3 Applications
4 See also
5 References
6 External links



Composition

MMCs are made by ....etc

[:=Read Full Message Here=:]