Presented by
Aiswariya R



JK Flip-flop
• The most versatile of the flip-flops
• Has two data inputs (J and K)
• Do not have an undefined state like SR flip-flops
– When J & K both equal 1 the output toggles on the active clock edge
Characteristics of JK flip-flop
 If one input (J or K) is at logic 0, and the other is at logic 1, then the output is set or reset (by J and K respectively), just like the RS flip-flop, but on the (falling) clock edge.
 If both inputs are 0, then it remains in ....etc

[:=Read Full Message Here=:]

In the development of packaging of electronics the aim is to lower cost, increase the packaging density, and improve the performance while still maintaining or even improving the reliability of the circuits. Flip chip microelectronic assembly is the direct electrical connection of face-down electronic components onto substrates, circuit boards, or carriers, by means of conductive bumps on the chip bond pads since the chip is directly attached to the substrate, board, or carrier by the conductive bumps. Flip chip has advantage in size, performan ....etc

[:=Read Full Message Here=:]

DM74LS373/DM74LS374 3-STATE Octal D-Type Transparent Latches and
Edge-Triggered Flip-Flops


General Description

These 8-bit registers feature totem-pole 3-STATE outputs designed specifically for driving highly-capacitive or relatively low-impedance loads. The high-impedance state and increased high-logic level drive provide these registers with the capability of being connected directly to and driving the bus lines in a bus-organized system without need for interface or ....etc

[:=Read Full Message Here=:]

I am Nur I would like to get details on disadvantages of flip-flops. My friend Sarah said disadvantages of flip-flops will be available here and now I am living in Malaysia and I studied in the college UMT and now I am doing researched about this and I need your help. ....etc

[:=Read Full Message Here=:]

Assume that there is a parking area in a shop whose capacity is 10. No more than 10 cars are allowed inside the parking area and the gate is closed as soon as the capacity is reached. There is a gate sensor to detect the entry of car which is to be synchronized with the clock pulse. Design and implement a suitable counter using JK flip flops. Also determine the number of flip flops to be used if the capacity is increased to 50. ....etc

[:=Read Full Message Here=:]

Name– study of RS flip-flop using NAND gates and NOR gates.
Aim – to study the working of RS flip-flop using NAND gates and NOR gates and compare them.
Apparatus – IC 7400, IC 7402, circuit board, power supply +5V DC, LEDs, connecting wires, soldering iron, cutter etc.
Circuit diagrams


Procedure –
1) You are given IC 7400 and IC 7402. Identify the ICs by reading their numbers and details from above given pin configurations.
2) Connect the gates with their ....etc

[:=Read Full Message Here=:]

PRESENTED BY:
B.Vinod kumar
Z.Vijay kumar
C.V. Karunakar reddy
M.Sreeja
G.Ramesh


objective
In present CMOS circuits the power dissipation caused by leakage current cannot be neglected as the technology scaling down
Here single treshold transmission gate D flip flop is the bench circuit and new transmission gate flip flop based on different techniques are used
Here the techniques like dual threshold and the stacking of MTCMOS transistors is used to reduce the leakage current.
The v ....etc

[:=Read Full Message Here=:]

Hi, I am Lyneth Delas Llagas, I would like to get details on circuit diagram for automatic car parking using flip flops. I was informed that the circuit diagram is available here. I'm currently an electronics engineering student at De La Salle Lipa. I need help on how a car parking system would be implemented using flip flops. Please allow me to get the details for my project. Thank you so much! ....etc

[:=Read Full Message Here=:]

In the development of packaging of electronics the aim is to lower cost, increase the packaging density, and improve the performance while still maintaining or even improving the reliability of the circuits. Flip chip microelectronic assembly is the direct electrical connection of face-down electronic components onto substrates, circuit boards, or carriers, by means of conductive bumps on the chip bond pads. Flip chip is also called Direct Chip Attach (DCA), since the chip is directly attached to the substrate, board, or carrier by the conducti ....etc

[:=Read Full Message Here=:]

Flip Chip Packaging



What is Flip Chip?

VISIT AMKOR TECHNOLOGY
ONLINE FOR LOCATIONS AND TO
VIEW THE MOST CURRENT
PRODUCT INFORMATION.
Flip Chip (FC) is not a specific package (like SOIC), or even a package type (like BGA). Flip Chip describes the
method of electrically connecting the die to the package carrier. The package carrier, either substrate or leadframe,
then provides the connection from the die to the exterior of the package. In standard p ....etc

[:=Read Full Message Here=:]