DESIGN AND FABRICATION OF PLATE FREEZER
PROJECT REPORT

ABSTRACT
Techniques of freezing vary for each application, The type of refrigeration used for preserving fruits cannot suit the need of the fish industries. Later it has been discovered that the number of viable vegetative microorganisms in food are usually greatly reduced by freezing if quick freezing is employed. The conventional freezers could not cope with this higher rate of freezing. By the development of the plate freezer, the challenge of quick freezing ha ....etc

[:=Read Full Message Here=:]

DESIGN AND FABRICATION OF PULSE TUBE REFRIGERATION SYSTEM

ABSTRACT
Cooling effect at one end of a hollow tube with a pulsating pressure in the inside gas, was first observed by Gifford and Longsworth in early sixties. This marks the inception of one of the most promising cryogenic refrigerators known as 'pulse tube refrigerator' (PTR). Cryogenics is the science of low temperature. Cryogenics refers to the entire phenomenon occurring below -150°C or 123K. Cryogenic engineering involves the design and development of ....etc

[:=Read Full Message Here=:]

Design and Fabrication of GearBox
AIM: To design and fabricate a automobile gearbox

Objectives
To design a Helical gear box
Study of various gear manufacturing processes
Fabrication of gear box
Representation of Gearbox
Market Survey
Market research was done at following places regarding type and cost calculation of the Gearbox.

Sokhi heli-wom gears pvt.ltd in Ghaziabad
Hi-tech gears in Manesar
Junk market in Mayapuri

Gearbox
A transmission or gearbox provides speed and� ....etc

[:=Read Full Message Here=:]

Presented In:
MECHANICAL ENGINEERING DEPARTMENT
JIND INSTITUTE OF ENGINEERING AND TECHNOLOGY, JIND

1.0 INDRODUCTION
An escalator is a moving staircase conveyor transport device for carrying people between floors of a building. The device consists of a motor-driven chain of individual, linked steps that move up or down on tracks, allowing the step treads to remain horizontal.
Escalators are used around the world to move pedestrian traffic in places where elevators would be impractical. Principal areas of u ....etc

[:=Read Full Message Here=:]

DESIGN AND FABRICATION OF FREE MAGNETO ENERGY SYSTEM
PROJECT MEMBERS:
MOHAMMED AZHAR.M
SYED GHOUSE BASHA.A
VINOTH KUMAR.V
VINOTH.K

GUIDE BY
Mr.PRASATH M.E
ABSTRACT
The Free magneto energy system is totally based on energy conversion method.
The magnetic energy is used to generate the electric power.
This is used to emergency power system.
Ultimate aim of our project is to produce electric energy with out emission ....etc

[:=Read Full Message Here=:]

....etc

[:=Read Full Message Here=:]

Hello,

I'm Hariharan from PSG Tech. I saw the list of automobile projects that was available and the topic DESIGN AND FABRICATION OF PROPELLER SHAFT AND TIE ROD BEND TESTING AND BEND REMOVING MACHINE caught my eye.
I'm interested in knowing more on this project, i.e instructions on how to build it and its report.
I've planned to select this topic for my mini project, so an earlier reply will be much appreciated.

Regards
....etc

[:=Read Full Message Here=:]

DESIGN, FABRICATION AND PERFORMANCE EVALUATION OF GARDEN TILLER

ABSTRACT
In order to meet the food requirements of the growing population and rapid industrialization, modernization of agriculture is inescapable. Mechanization enables the conservation of inputs through precision in metering ensuring better distribution, reducing quantity needed for better response and prevention of losses or wastage of inputs applied. Mechanization reduces unit cost of production through higher productivity and input conservation.
The p ....etc

[:=Read Full Message Here=:]

ABSTRACT
The subject gives a brief look on the suitability of composite leaf spring on vehicles and their advantages. Efforts have been made to reduce the cost of composite leaf spring to that of steel leaf spring. The achievement of weight reduction with adequate improvement of mechanical properties has made composite a very replacement material for convectional steel. Material and manufacturing process are selected upon on the cost and strength factor. The design method is selected on the basis of mass production.
From t ....etc

[:=Read Full Message Here=:]

Full Report for Mini Hydraulic jack press ....etc

[:=Read Full Message Here=:]