Wireless Charging
Submitted By
Mr.Deshmukh Sachin Bharat
Er. Rathi P.K. Er. Borkar B.S.
Seminar Guide Seminar Co-Ordinator
Department of Information Technology,
Amrutvahini College of Engineering,
Sangamner “ 422608
ABSTRACT
It seems these days that everyone has a cellular phone. Whether yours is for business purposes or personal use, you need an efficient way of charging the battery in the phone. But, like most people, you probably donâ„ ....etc

[:=Read Full Message Here=:]

presented By
Shane Dunlevy


System Basics
• Hydraulic actuation allows multiplication of pedal force.
• In this system, a 10lb force on the pedal produces 360 lbs of force at the friction surface.
Braking Dynamics
• Dynamic weight transfer caused by braking shifts the weight balance towards the front of the car
• Dynamic weight for the front and rear can be found using Newton’s Law
Braking Dynamics
• Because the maximum braking force is equal to the coefficient of friction tim ....etc

[:=Read Full Message Here=:]

162/2014
Maximum : 100 marks
Time : 1 hour and 15 minutes

1. Steel rules are made up of:
(A)Spring steel
(B)Mild steel
(C )Cast iron
(D)High carbon steel

2.These calipers are also known as Hermaphrodite calipers.
(A)Jenny caliper
(B)Firm joint calipers
(C )Spring calipers
(D)None of the above

3.The angle of prick punch is :
(A)60 degree
(B)45 degree
(C )30 degree
(D)53 degree

4.The saw used for manual sawing is known as :
(A)Band saw
(B)Hack saw
(C )Circular saw
(D)Jig saw

5.The method of se ....etc

[:=Read Full Message Here=:]

Hydraulic Brake System
The Hydraulic brake system is a braking system which uses brake fluid usually includes ethylene glycol, to transmit pressure from the controlling unit, which is usually near the driver, to the actual brake mechanism, which is near the wheel of the vehicle.
The most common arrangement of hydraulic brakes for passenger vehicles, motorcycles, scooters, and mopeds, consists of the following
¢ Brake pedal or Brake lever
¢ Pushrod, also called an actuating rod
¢ Reinforced hydraulic lines
¢ Rotor or a brake di ....etc

[:=Read Full Message Here=:]

1.The size of a hammer is generally specified by :
(A)Length of its head
(B)Diameter of its face
(C ) Length of its eye hole
(D) Weight of its head

2.Name the chisel which has a thicker and stronger blade than ordinary firmer chisel.
(A)Paring chisel
(B)Bevel edge firmer chisel
(C )Registered firmer chisel
(D)Gouge chisel

3.While sawing with a I land saw, the sight of eye should be :
(A)Away from thesaw
(B)On the right side of the saw
(C )On the left sideof the saw
(D)Directly above the saw

4.Hard Woods ....etc

[:=Read Full Message Here=:]

95/2015
Maximum : 100 marks
Time : 1 hour and 15 minutes

1.The size of bench vice is specified by :
(A)Weight of vice
(B)Length of spindle
(C )Width of jaws
(D)Length of handle

2.The narrow and thin part of a file which fits into the handle is :
(A)Shoulder
(B) Heel
(C ) Tip
(D) Tang

3.In single cut file the teeth are at an angle of---------------- degree to the centre line.
(A) 40
(B) 70
(C ) 57
(D) 60

4.These files are available only in half round shape.
(A) Rasp cut file
(B) Single cut file
( ....etc

[:=Read Full Message Here=:]

1.The vernier bevel protractor is able to read the angle to an accurancy of _____degrees. The vernier bevel protractor is able to read the angle to an accuracy of
(A)1°
_r
12
(C )1°/2
(B)1/2
(D)11°/2

2.------------method is used in mass production for producing a small length of taper where
accuracy is not the criserion.
(A)Form Tool(B) Tail Stock Offset
(C ) Swivelling Compound rest(D) None of these

3.In tailstock offset taper turning method, the amount of offset is found by the formula :
(A)
(C )
(.D-d) ....etc

[:=Read Full Message Here=:]

Metal matrix composite

A metal matrix composite (MMC) is composite material with at least two constituent parts, one being a metal. The other material may be a different metal or another material, such as a ceramic or organic compound. When at least three materials are present, it is called a hybrid composite. An MMC is complementary to a cermet.Contents
1 Composition
1.1 Matrix
1.2 Reinforcement
2 Manufacturing and forming methods
3 Applications
4 See also
5 References
6 External links



Composition

MMCs are made by ....etc

[:=Read Full Message Here=:]

ABSTRACT
Hy-Wire Car is without mechanical and hydraulic linkage end engine. Instead of these it contain a fuel cell stack and a drive by wire system. It is fully automated car it is a future car. In future it will have a wide application. The problem with fuel consumption and pollution can be minimize to certain level.
Chapter I
INTRODUCTION
Cars are immensely complicated machines, but when you get down to it, they do an incredibly simple job. Most of the complex stuff in a car is dedicated to turning whee ....etc

[:=Read Full Message Here=:]

Mini project report on
PLANER MILLING MACHINE ACCOMMODATED WITH DRILL HEAD

INTRODUCTION:
What is Planer-milling machine?

Planers and shapers are now obsolescent, because milling machines have eclipsed them as the machine tools of choice for doing work, as the rate of metal removal is quantitative.
planer-milling machines come in two kinds: double-housing and open-side. The double-housing variety has vertical supports on both sides of its long bed; the open-side variety has a vertical support on only one side ....etc

[:=Read Full Message Here=:]