presented By
Shane Dunlevy


System Basics
• Hydraulic actuation allows multiplication of pedal force.
• In this system, a 10lb force on the pedal produces 360 lbs of force at the friction surface.
Braking Dynamics
• Dynamic weight transfer caused by braking shifts the weight balance towards the front of the car
• Dynamic weight for the front and rear can be found using Newton’s Law
Braking Dynamics
• Because the maximum braking force is equal to the coefficient of friction tim ....etc

[:=Read Full Message Here=:]

The sole motive of an AUTOSAR is the replacement of the proprietary standards of the software system functions, into an open standard. This helps in building a plug-and-play atmosphere where the software modules can go hand in hand with the electronic architecture at the same time. This creates an open standard for automotive E/E architecture. This in turn will help in having a standardized tool chain that can become the fundamental building block for management functions for both the future applications and standard software modules. ....etc

[:=Read Full Message Here=:]

Automotive Electronic Systems
Outlines
Developing Trends of Automotive Electronic Systems
Emerging In-Vehicle Networks
Developing Trends of Automotive Electronic Systems
Automotive Electronic Systems Today
Expanding Automotive Electronic Systems
Expanding Automotive Electronic Systems
The mature subsystems of automotive electronic systems
Powertrain/Body control—EMS, ABS, …
Themes of current stage
X-by-wirean ongoing revolution in vehicle electronics architecture
Themes of next stage
Infotainment= ....etc

[:=Read Full Message Here=:]

Abstract
A new printed antenna system mounted in an aperture in the roof of a car is evaluated for broadcast signal reception from 88-108 MHz. Results from simulations on the vehicle are compared with measurements. The overall performance of the antenna is also compared to common types of vehicle antennas, the roof monopole and a glass based antenna. Overall the average gain of the antennas was better than -3 dBi for vertical polarization and -10 dBi for horizontal while the input return loss was generally better than -2 dB before matching sec ....etc

[:=Read Full Message Here=:]

different antennas have been developed and investigated for RKE (Remote Keyless Entry) and related automotive applications. These antennas include small printed-on-dielectric passive and active, printed-on glass, and whip-splitter types. Key antenna parameters-including size, performance, antenna shape-are proposed, investigated,The characteristics of small antennas taking into account the often significant effect of the cable length and direction position have also been investigated and are presented; solutions are also presented that eliminat ....etc

[:=Read Full Message Here=:]

ABSTRACT
An automotive propulsion concept is presented which
utilizes liquid nitrogen as the working fluid for an open
Rankine cycle. Ambient heat exchangers are used to power
an engine that is configured to maximize heat transfer during
the expansion stroke. If sufficient heat input during the
expansion process can be realized then this cryogenic
propulsive system would provide greater automotive ranges
and lower operating costs than those of electric vehicles
currently being considered for mass production.
The
feasibility of meeti ....etc

[:=Read Full Message Here=:]

This report presents the results of an independent evaluation of the Automotive Collision Avoidance System (ACAS). The ACAS integrates forward collision warning (FCW) and adaptive cruise control (ACC) functions for light-vehicle applications. The FCW detects, assesses, and alerts the driver of a potential hazard in the forward region of the vehicle. The ACC provides automatic brake and throttle actuation in order to maintain speed and longitudinal headway control. Through the integration of these two functions, ACAS is intended to improve auto ....etc

[:=Read Full Message Here=:]

automotive suspension and steering systems pdf download ....etc

[:=Read Full Message Here=:]

USB EXPLAINED: AN INTRODUCTION TO USB AND ITS FUTURE


USB HISTORY
The Universal Serial Bus (USB) was introduced to the world of PC computing to solve the growing problem of how
to connect peripherals to a PC. The world of desktop computers needed a way, not only to physically connect
devices, but also allow them to be identified and categorized to enable a simple ease of use and method of discovery.
Prior to USB, many people overloaded the use of their serial and ....etc

[:=Read Full Message Here=:]

An embedded system is a special-purpose system in which the computer is completely encapsulated by the device it controls. Unlike a general-purpose computer, such as a personal computer, an embedded system performs one or a few pre-defined tasks, usually with very specific requirements. Since the system is dedicated to specific tasks, design engineers can optimize it, reducing the size and cost of the product.

http://ziddudownload/5571379/Automotivebasedmanag.rar.html ....etc

[:=Read Full Message Here=:]