TRADESMAN - SMITHY - FORGING AND HEAT TREATING - kerala psc previous question paper
#1


.pdf   TRADESMAN - SMITHY - FORGING AND HEAT TREATING - TECHNICAL EDUCATION - KTM AND KKD.pdf (Size: 1.05 MB / Downloads: 0)

1. The term forging refers to :
(A)Plastic deformation
(B)Plastic deformation
(C )Stress deformation
(D)Strain reveling

2.A very difficult forgable material is :
(A)Maraging Steel
(B)Beryllium
(C )Magnesium alloy
(D)Nickel alloy

3.The highly elastic material is :
(A)Rubber
(B)Brass
(C )Glass
(D)Steel

4.Slow and progressive deformation is called :
(A)Resilience
(B)Malleability
(C )Creep
(D)Plasticity

5.When a material is subjected to cyclic periodic loading, the property' occurring is :
(A)Creep
(B)Fatigue
(C )Hardness
(D)Ductility

6.Hooke's Law states that:
(A)Stress x Strain = Constant
(B)Strain - Stress = Constant
(C )Stress = Constant Strain
(D)Stress + Strain = Constant

7.The process of forming new grain structure with reduced grain size when a metal is heated and deformed is called :
(A)Re-crystallisation
(B)Crystallisation
(C )Melting
(D)Deforming

8.Hot working temperature of steel is :
(A) 370-455°C
(B)760-925oC
(C ) 315°C
(D) 1100-1260’C

9.length of work piece is reduced by :
(A) Upsetting
(B) Fullering
(C ) Flattening 
(D) Piercing

10.The cooling medium in normalising is : 
(A) Water 
(B) Oil
(C ) Air
(D) Artificial Coolants

11. Pure Iron melts at :
(A) 380oC
(B)760°C
(C ) 370oC
(D) 1539°C

12. Martensite is : 
(A) Ductile
(B) Hard
(C ) Soft
(D) Brittle

13. Toughness is the ability to absorb : 
(A) Impact
(B) Stresses
(C ) Load
(D) Heat

14.Heat treatment is done to change :
(A) Magnetic properties of metal
(B)Physical properties of metal
(C ) Mechanical properties of metal
(D) Electrical properties of metal

15.Which of the below is not a surface hardening process ?
(A) Nitriding
(B) Carburising 
(C ) Cyaniding 
(D) Annealing

16.A brittle material is : 
(A) Mild steel 
(C ) Low carbon steel
(B) Cast iron 
(D) Plastic

17.Gamma Iron has the crystal structure of:
(A)bee.
(B) sc
(C ) hep
(D) fcc

18.The property by which a material absorbs energy without plastic deformation is :
(A) Resilience
(B) Hardness
(C ) Tensile Strength
(D) Toughness

19.In forging operation, work piece is usually subjected to :
(A)Tensile stress
(B)Shear stress 
(C )Bending stress
(D)Compressive stress

20.Forging is a:
(i)Hot working operation
(ii)Cold working operation
(iii)Operation that involves pressing Of these statements :
(A)(i) is true
(B)(ii) and (iii) arc true 
(C )(ii) is true
(D)(i) and (iii) are true

21.Hotdie forging is also known as :
(A)Roll forging
(B)Embossing 
(C )Isothermal forging
(D)Precision forging

22.Thebody of Anvil is made of:
(A)Mild steel
(B)High carbon steel 
(C )High speed steel
(D)Cast iron

23.In Anvil, hardie hole is used for :
(A)Bending rods of small diameters
(B)Hot punching operation
(C )Holding square shanks
(D) Cutting operation

24.In smithy operation, for general pick up work :
(A)Straight - lip fluted tong is used 
(B)Flat tong is used
(C )Gad tong is used
(D)Ring tong is used

25.Necking down of work piece is done by :
(A)Swages
(B)Fullers
(C )Flatters
(D)Set hammer

26.Flux used in forge welding is :
(A)Calcined Borax
(B)Silica
(C )Nitric Oxide
(D)Calcium Carbonate

27.The method of preparing metal pieces for forge welding is called :
(A)Filling
(B)Jumping
(C )Reaming
(D)Scarfing

28.Drop forging comes under :
(A) Smith die forging
(B) Impression die forging
(C )Power forging
(D)Hand forging

29.Forging process for shaping round bars is called :
(A)Press forging
(B)Rotary forging 
(C )Drop forging
(D)Billet

30.Iron with little or no carbon is called :
(A)Ferrite
(B)Sorbite
(C )Pearlite
(D)Martensite

31.The hardening response of steel to heat treatment is measured by :
(A)Brinell Test
(B)Jominy Test
(C )Morse Test
(D)Knoop Test

32.Which of the following metal is magnetic ?
(A)Aluminium
(B)Nickel
(C )Copper
(D)Magnesium

33.The metal used for die casting is :
(A)Copper
(B)Magnesium
(C )Zinc
(D)Lead

34.Metal with low melting point is :
(A)Lead
(B)Tin
(C )Zinc
(D)All the above

35.Galvanization is the process of coating :
(A)Tin
(B)Zinc
(C )Nickel
(D)Copper

36.Age hardening of non-ferrous metals is called :
(A) Case hardening
(B) Nitriding
(C ) Precipitation hardening
(D) Surface hardening

37.Dolomite is an important ore of:
(A)Lead
(B)Copper
(C )Magnesium
(D)Aluminium

38.The process of making blind holes is :
(A)Piercing
(B)Punching
(C )Blocking ,
(D) Bending

39.The process of hammering a heated bar into aligned die cavity is called :
(A)Press forging 
(B)Drop forging
(C )Roll forging
(D)Rotary forging

40.Pitting of the forging surface is caused by :
(A)Slag
(B)Over heating
(C )Scale
(D)Low heating

41.The defect occurred in some alloy steel due to rapid cooling from forging temperature is:
(A)Creep
(B)Flakes
(C )Cracks
(D)Dents

42.The defect caused by misalignment between top and bottom forging dies is called :
(A) Fins and rags 
(B) Die shift
(C ) Cracks
(D) Hair cracks

43.Simple way to remove scale from a forged part is :
(A) Using steam and compressed air 
(B) Pickling
(C ) Tumbling process
(D) Blast cleaning

44.The Final treatment after forging is done to :
(A) Remove stresses
(B)Make the forged parts cool
(C ) Make the forging hard and tough 
(D) To clear cracks

45.Flat forging of gear blanks are usually done by :
(A)Upsetting
(B)Downsetting
(C )Hammering
(D)Squeezing

46.During tempering, forged parts are cooled using :
(A)Oil
(B)Water
(C )Air
(D)Coolants

47.The mechanism used in presses for freeing the work piece from a die is called :
(A) Die set
(B) Knock out 
(C ) Stroke '
(D) Stripper

48.The process of thinning the walls of a shell by forcing it through a die with a punch is called :
(A)Bending
(B)Rolling
(C )Re-drawing
(D)Ironing

49.Vacancy is :
(A)Point defect
(B)Line defect
(C )Surface defect
(D)Volume defect

50.Which one of the below is used to eliminate coarse grained structure :
(A)Annealing
(B)Tempering
(C )Cyaniding
(D)Normalising

51.Quenching is the process of:
(A) Rapid cooling of metals
(B) Slow cooling of metals
(C ) Intermediate cooling of metals
(D) Heating of metals

52.The ability of the material to resist deformation is :
(A) Ductility
(B) Creep
(C ) Fatigue strength 
(D) Stiffness

53.Poisson's ratio is the ratio between :
(A) Strain to longitudinal stress 
(B) Transverse strain to axial strain 
(C ) Longitudinal stress to axial strain 
(D) Longitudinal stress to strain

54.For ductile materials, factor of safety is :
(A)Ultimate stress/Design stress
(B)Induced stress/Design stress
(C )Yield stress/ Design stress 
(D)Design stress/ Yield stress

55.Carbon content in cast iron is :
(A)3.2-5.2%
(B)2.1-4.5%
(C )8.3-9.2%
(D)1.2-2%

56.The hardest known material is :
(A)High speed steel
(B)Carbides
(C )Ceramics
(D)Diamond

57.The ability of a material that can be drawn into thin wire is :
(A)Hardness
(B)Tensile strength
(C )Creep
(D)Ductility

58.Alloying of vanadium increases :
(A)Toughness and wear resistance of steel
(B)Hardenability of steel
(C )Oxidation resistance of steel
(D)Corrosion resistance

59.The purest iron is :
(A) Wrought iron 
(B) Pig iron
(C ) Electrolytic iron 
(D) Cast iron

60.TTT stands for :
(A)Time Temperature Transformation
(B)Temperature Toughness Time
(C )Toughness Transformation Time
(D)Total Time Transformation

61.The welding accompanied by the application of pressure is :
(A)Gas welding
(B)Fusion welding
(C )Plastic welding
(D)Arc welding

62.The change of state of alloys due to variation in temperature and concentration is represented by:
(A) Phase rule
(B) Phase diagram
(C ) Equilibrium diagram
(D) Graphs

63.The fuel used in hearth is :
(A)Coke .
(B)Wood
(C )Methane
(D)Oil

64.The forging temperature of wrought iron is :
(A)800-1150°C
(B)900- 1300°C
(C )750-1250°C
(D)400-500°C

65.An English anvil has :
(A)Two beaks
(B)No beaks
(C )Three beaks
(D)One beak

66.Swage block is made of:
(A)Mild steel
(B)HSS
(C )Cast iron
(D)High carbon steel

67.Open mouth tong is used to hold :
(A)Heavier stock
(B)Round stock 
(C )Square stock 
(D)Ductilestock

68.Cold chisel has a cutting angle of:
(A)45°
(B)30°
(C )30°
(D)60°

69.Necking down of a work is done by :
(A)Set hammer
(B)Punches
(C )Fullers
(D)Squarepunch

70.Before scarf welding the ends of work pieces are :
(A)Made square
(B)Rounded
(C )Filed
(D)Cooled

71.The forging machine working by pressure are called :
(A)Hammers
(B)Pressure hammers
(C )Presses
(D)Ramming machine

72.Thecommon mass of Anvil is about:
(A)150 kg 
(B) 200 kg
(C )100 kg 
(D)250 kg

73.Thevice commonly used in smithy is :
(A)Hand vice 
(B) Bench vice
(C )Carpenter's vice
(D)Leg vice

74.Theangle of double cut file is :
(A)60° and 80° 
(B) 60° and 70°
(C )80o and 50°
(D)45° and 60°

75.Thematerial for hacksaw blade is :
(A)HCS 
(B) HSS
(C )Tool steel
(D)Vanadium steel

76.Prick punch has an approximate included angle of :
(A)30°
(B)90°
(C )35°
(D) 40°

77.Least count of steelrule is :
(A)0.5 mm
(B)0.05 mm
(C )0.25 mm
(D)0.1 mm

78.For smithy operation an anvil used to hold small work piece is :
(A)Bench vice
(B)Hand vice
(C )Bick iron
(D)Leg vice

79.Tool used to level and finish the comers of flat surfaces is :
(A)Set hammer
(B)Fuller
(C )Drift
(D)Swage

80.Effective length of a file is the distance from :
(A)Point to the heel
(B)End of handle to thepoint
(C )Tang to edge
(D)Tang to point

81.The River which originated from the "Gaymukh" cave of Himalaya :
(A)Ganga
(B)Brahmaputhra 
(C )Sindhu
(D)Tapti

82.The Indian Museum situated in the place of:
(A)Kolkatta
(B)Mumbai
(C )Delhi
(D)Kanpur

83.The institution which calculates India's national income :
(A)Central StatisticalOrganisation
(B)Planning Commission
(C )National DevelopmentCouncil
(D)Finance Ministry

84.National Rural Employment Guarantee Act was passed in the year :
(A)2004
(B)2006
(C )2008
(D)2005

85.The architect of first five year plan of India is :
(A) R. Rangarajan
(B)K.M. Raj
(C ) J.C. Kumarappa
(D) P.C. Mahalanobis

86.The Cashewnut Research Station of Kerala is existed in :
(A)Panniyur
(B)Vellanikkara
(C )Anakkayam
(D)Pattambi

87.'Ashtamudi kayal' existed in the district of:
(A)Kottayam
(B)Ernamkulam
(C )Alappuzha
(D)Kollam

88. The District with least coastal plains 
(A) Emamkulam 
(B) Kollam
(C ) Kannur
(D) Kasaragode

89.The town 'Cheruthuruthy' situated on the River bank of : 
(A) Kadalundi 
(B) Bharathapuzha 
(C ) Periyar
(D) Chaliyar

90.Name the agitation started in Kerala as a protest against the constitutional reforms of 1932 : 
(A) Channar revolt
(B) Kayyur riot
(C ) Punnapra vayalar agitation 
(D) Nivarthana agitation

91.The founder of 'Prathvaksha Raksha Daivasabha (PRDS) was : 
(A) Ayyankali
(B) Pandit Karuppan
(C ) Kumara Guru
(D) Kumaranasan

92.Who conducted 'Yachana Yathra' from Trichur to Kasaragode to collect money for the programme of educational reforms ?
(A) Poikayil Yohannan
(B) Dr.Palpu
(C ) V.T. Vattatirippad
(D) Chattampi Swamikal

93.Identify the founder of 'Ananda Mahasabha' :
(A)Ayya Vaikundar
(B)Kumaranasan
(C ) Brahmanada Sivayogi
(D) Mannathu Padmanabhan

94.When did Father Kuriakose Elias Chavara was beatified by Pope John Paul II ?
(A)1986
(B)1976
(C )1982
(D)1988

95.The district which firstly declared as 'Smoke Free District' in India :
(A)Kottayam
(B)Kozhikkode
(C )Ernamkulam
(D)Alappuzha

96.Name the literary works which secured Odakkuzhal award in 2013 :
(A)Marupiravi
(B)ManushyanuOru Amukham
(C ) Aarachar
(D) Ammakku Oru Tharattu

97.The first Malayalam University of Kerala is setup in the District of:
(A)Kannur
(B)Kozhikode
(C )Palakkad
(D)Malappuram

98.How many digits consists in the unique idnumber of AADHAR ?
(A)11
(B)12
(C )10
(D)13

99.'Operation New Dawn' is the beginning of stability in :
(A)Afganisthan
(B)Iran
(C )Iraq
(D)Sudan

100.The Bodo language is spoken in the state of:
(A)Mizoram
(B)Tripura
(C )Arunachal Pradesh
(D)Assam
Reply

Important Note..!

If you are not satisfied with above reply ,..Please

ASK HERE

So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page
Popular Searches: pnumantic forging machine mini projects, pneumatic forging machine project report, full seminar report on forging, pneumatic forging machines, industrial visit report on forging, a complete seminar report on forging, pneumatic forging machine with synopsis download,

[-]
Quick Reply
Message
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  LABORATORY TECHNICIAN GR II LABORATORY ASST - kerala psc previous question paper amrutha735 1 11,344 25-01-2018, 03:15 PM
Last Post: Guest
  BIO-MEDICAL ENGINEER - MEDICAL EDUCATION kerala psc previous question paper amrutha735 1 9,521 23-01-2018, 11:22 PM
Last Post: RamiGycle
  X-RAY TECHNICIAN GR-II -kerala psc previous question paper amrutha735 0 9,299 15-05-2017, 04:59 PM
Last Post: amrutha735
  WORKSHOP INSTRUCTORINSTUCTOR GARDE - kerala psc previous question paper amrutha735 0 8,392 15-05-2017, 04:57 PM
Last Post: amrutha735
  WORK SUPERVISOR - OVERSEER GRADE II - kerala psc previous question paper amrutha735 0 8,531 15-05-2017, 04:53 PM
Last Post: amrutha735
  WORK SUPERINTENDENT - AGRICULTURE - kerala psc previous question paper amrutha735 0 8,803 15-05-2017, 04:52 PM
Last Post: amrutha735
  VOCATIONAL TEACHER RECEPTION BOOK -kerala psc previous question paper amrutha735 0 8,408 15-05-2017, 04:50 PM
Last Post: amrutha735
  VOCATIONAL INSTRUCTOR IN GENERAL INSURANCE-kerala psc previous question paper amrutha735 0 8,521 15-05-2017, 04:49 PM
Last Post: amrutha735
  VOCATIONAL INSTRUCTOR IN COMPUTER APPLICATION-kerala psc previous question paper amrutha735 0 8,623 15-05-2017, 04:47 PM
Last Post: amrutha735
  VOCATIONAL INSTRUCTOR - CATERING -kerala psc previous question paper amrutha735 0 8,580 15-05-2017, 04:45 PM
Last Post: amrutha735

Forum Jump: