13-05-2017, 04:54 PM
[attachment=1581]
1. The term forging refers to :
(A)Plastic deformation
(B)Plastic deformation
(C )Stress deformation
(D)Strain reveling
2.A very difficult forgable material is :
(A)Maraging Steel
(B)Beryllium
(C )Magnesium alloy
(D)Nickel alloy
3.The highly elastic material is :
(A)Rubber
(B)Brass
(C )Glass
(D)Steel
4.Slow and progressive deformation is called :
(A)Resilience
(B)Malleability
(C )Creep
(D)Plasticity
5.When a material is subjected to cyclic periodic loading, the property' occurring is :
(A)Creep
(B)Fatigue
(C )Hardness
(D)Ductility
6.Hooke's Law states that:
(A)Stress x Strain = Constant
(B)Strain - Stress = Constant
(C )Stress = Constant Strain
(D)Stress + Strain = Constant
7.The process of forming new grain structure with reduced grain size when a metal is heated and deformed is called :
(A)Re-crystallisation
(B)Crystallisation
(C )Melting
(D)Deforming
8.Hot working temperature of steel is :
(A) 370-455°C
(B)760-925oC
(C ) 315°C
(D) 1100-1260’C
9.length of work piece is reduced by :
(A) Upsetting
(B) Fullering
(C ) Flattening
(D) Piercing
10.The cooling medium in normalising is :
(A) Water
(B) Oil
(C ) Air
(D) Artificial Coolants
11. Pure Iron melts at :
(A) 380oC
(B)760°C
(C ) 370oC
(D) 1539°C
12. Martensite is :
(A) Ductile
(B) Hard
(C ) Soft
(D) Brittle
13. Toughness is the ability to absorb :
(A) Impact
(B) Stresses
(C ) Load
(D) Heat
14.Heat treatment is done to change :
(A) Magnetic properties of metal
(B)Physical properties of metal
(C ) Mechanical properties of metal
(D) Electrical properties of metal
15.Which of the below is not a surface hardening process ?
(A) Nitriding
(B) Carburising
(C ) Cyaniding
(D) Annealing
16.A brittle material is :
(A) Mild steel
(C ) Low carbon steel
(B) Cast iron
(D) Plastic
17.Gamma Iron has the crystal structure of:
(A)bee.
(B) sc
(C ) hep
(D) fcc
18.The property by which a material absorbs energy without plastic deformation is :
(A) Resilience
(B) Hardness
(C ) Tensile Strength
(D) Toughness
19.In forging operation, work piece is usually subjected to :
(A)Tensile stress
(B)Shear stress
(C )Bending stress
(D)Compressive stress
20.Forging is a:
(i)Hot working operation
(ii)Cold working operation
(iii)Operation that involves pressing Of these statements :
(A)(i) is true
(B)(ii) and (iii) arc true
(C )(ii) is true
(D)(i) and (iii) are true
21.Hotdie forging is also known as :
(A)Roll forging
(B)Embossing
(C )Isothermal forging
(D)Precision forging
22.Thebody of Anvil is made of:
(A)Mild steel
(B)High carbon steel
(C )High speed steel
(D)Cast iron
23.In Anvil, hardie hole is used for :
(A)Bending rods of small diameters
(B)Hot punching operation
(C )Holding square shanks
(D) Cutting operation
24.In smithy operation, for general pick up work :
(A)Straight - lip fluted tong is used
(B)Flat tong is used
(C )Gad tong is used
(D)Ring tong is used
25.Necking down of work piece is done by :
(A)Swages
(B)Fullers
(C )Flatters
(D)Set hammer
26.Flux used in forge welding is :
(A)Calcined Borax
(B)Silica
(C )Nitric Oxide
(D)Calcium Carbonate
27.The method of preparing metal pieces for forge welding is called :
(A)Filling
(B)Jumping
(C )Reaming
(D)Scarfing
28.Drop forging comes under :
(A) Smith die forging
(B) Impression die forging
(C )Power forging
(D)Hand forging
29.Forging process for shaping round bars is called :
(A)Press forging
(B)Rotary forging
(C )Drop forging
(D)Billet
30.Iron with little or no carbon is called :
(A)Ferrite
(B)Sorbite
(C )Pearlite
(D)Martensite
31.The hardening response of steel to heat treatment is measured by :
(A)Brinell Test
(B)Jominy Test
(C )Morse Test
(D)Knoop Test
32.Which of the following metal is magnetic ?
(A)Aluminium
(B)Nickel
(C )Copper
(D)Magnesium
33.The metal used for die casting is :
(A)Copper
(B)Magnesium
(C )Zinc
(D)Lead
34.Metal with low melting point is :
(A)Lead
(B)Tin
(C )Zinc
(D)All the above
35.Galvanization is the process of coating :
(A)Tin
(B)Zinc
(C )Nickel
(D)Copper
36.Age hardening of non-ferrous metals is called :
(A) Case hardening
(B) Nitriding
(C ) Precipitation hardening
(D) Surface hardening
37.Dolomite is an important ore of:
(A)Lead
(B)Copper
(C )Magnesium
(D)Aluminium
38.The process of making blind holes is :
(A)Piercing
(B)Punching
(C )Blocking ,
(D) Bending
39.The process of hammering a heated bar into aligned die cavity is called :
(A)Press forging
(B)Drop forging
(C )Roll forging
(D)Rotary forging
40.Pitting of the forging surface is caused by :
(A)Slag
(B)Over heating
(C )Scale
(D)Low heating
41.The defect occurred in some alloy steel due to rapid cooling from forging temperature is:
(A)Creep
(B)Flakes
(C )Cracks
(D)Dents
42.The defect caused by misalignment between top and bottom forging dies is called :
(A) Fins and rags
(B) Die shift
(C ) Cracks
(D) Hair cracks
43.Simple way to remove scale from a forged part is :
(A) Using steam and compressed air
(B) Pickling
(C ) Tumbling process
(D) Blast cleaning
44.The Final treatment after forging is done to :
(A) Remove stresses
(B)Make the forged parts cool
(C ) Make the forging hard and tough
(D) To clear cracks
45.Flat forging of gear blanks are usually done by :
(A)Upsetting
(B)Downsetting
(C )Hammering
(D)Squeezing
46.During tempering, forged parts are cooled using :
(A)Oil
(B)Water
(C )Air
(D)Coolants
47.The mechanism used in presses for freeing the work piece from a die is called :
(A) Die set
(B) Knock out
(C ) Stroke '
(D) Stripper
48.The process of thinning the walls of a shell by forcing it through a die with a punch is called :
(A)Bending
(B)Rolling
(C )Re-drawing
(D)Ironing
49.Vacancy is :
(A)Point defect
(B)Line defect
(C )Surface defect
(D)Volume defect
50.Which one of the below is used to eliminate coarse grained structure :
(A)Annealing
(B)Tempering
(C )Cyaniding
(D)Normalising
51.Quenching is the process of:
(A) Rapid cooling of metals
(B) Slow cooling of metals
(C ) Intermediate cooling of metals
(D) Heating of metals
52.The ability of the material to resist deformation is :
(A) Ductility
(B) Creep
(C ) Fatigue strength
(D) Stiffness
53.Poisson's ratio is the ratio between :
(A) Strain to longitudinal stress
(B) Transverse strain to axial strain
(C ) Longitudinal stress to axial strain
(D) Longitudinal stress to strain
54.For ductile materials, factor of safety is :
(A)Ultimate stress/Design stress
(B)Induced stress/Design stress
(C )Yield stress/ Design stress
(D)Design stress/ Yield stress
55.Carbon content in cast iron is :
(A)3.2-5.2%
(B)2.1-4.5%
(C )8.3-9.2%
(D)1.2-2%
56.The hardest known material is :
(A)High speed steel
(B)Carbides
(C )Ceramics
(D)Diamond
57.The ability of a material that can be drawn into thin wire is :
(A)Hardness
(B)Tensile strength
(C )Creep
(D)Ductility
58.Alloying of vanadium increases :
(A)Toughness and wear resistance of steel
(B)Hardenability of steel
(C )Oxidation resistance of steel
(D)Corrosion resistance
59.The purest iron is :
(A) Wrought iron
(B) Pig iron
(C ) Electrolytic iron
(D) Cast iron
60.TTT stands for :
(A)Time Temperature Transformation
(B)Temperature Toughness Time
(C )Toughness Transformation Time
(D)Total Time Transformation
61.The welding accompanied by the application of pressure is :
(A)Gas welding
(B)Fusion welding
(C )Plastic welding
(D)Arc welding
62.The change of state of alloys due to variation in temperature and concentration is represented by:
(A) Phase rule
(B) Phase diagram
(C ) Equilibrium diagram
(D) Graphs
63.The fuel used in hearth is :
(A)Coke .
(B)Wood
(C )Methane
(D)Oil
64.The forging temperature of wrought iron is :
(A)800-1150°C
(B)900- 1300°C
(C )750-1250°C
(D)400-500°C
65.An English anvil has :
(A)Two beaks
(B)No beaks
(C )Three beaks
(D)One beak
66.Swage block is made of:
(A)Mild steel
(B)HSS
(C )Cast iron
(D)High carbon steel
67.Open mouth tong is used to hold :
(A)Heavier stock
(B)Round stock
(C )Square stock
(D)Ductilestock
68.Cold chisel has a cutting angle of:
(A)45°
(B)30°
(C )30°
(D)60°
69.Necking down of a work is done by :
(A)Set hammer
(B)Punches
(C )Fullers
(D)Squarepunch
70.Before scarf welding the ends of work pieces are :
(A)Made square
(B)Rounded
(C )Filed
(D)Cooled
71.The forging machine working by pressure are called :
(A)Hammers
(B)Pressure hammers
(C )Presses
(D)Ramming machine
72.Thecommon mass of Anvil is about:
(A)150 kg
(B) 200 kg
(C )100 kg
(D)250 kg
73.Thevice commonly used in smithy is :
(A)Hand vice
(B) Bench vice
(C )Carpenter's vice
(D)Leg vice
74.Theangle of double cut file is :
(A)60° and 80°
(B) 60° and 70°
(C )80o and 50°
(D)45° and 60°
75.Thematerial for hacksaw blade is :
(A)HCS
(B) HSS
(C )Tool steel
(D)Vanadium steel
76.Prick punch has an approximate included angle of :
(A)30°
(B)90°
(C )35°
(D) 40°
77.Least count of steelrule is :
(A)0.5 mm
(B)0.05 mm
(C )0.25 mm
(D)0.1 mm
78.For smithy operation an anvil used to hold small work piece is :
(A)Bench vice
(B)Hand vice
(C )Bick iron
(D)Leg vice
79.Tool used to level and finish the comers of flat surfaces is :
(A)Set hammer
(B)Fuller
(C )Drift
(D)Swage
80.Effective length of a file is the distance from :
(A)Point to the heel
(B)End of handle to thepoint
(C )Tang to edge
(D)Tang to point
81.The River which originated from the "Gaymukh" cave of Himalaya :
(A)Ganga
(B)Brahmaputhra
(C )Sindhu
(D)Tapti
82.The Indian Museum situated in the place of:
(A)Kolkatta
(B)Mumbai
(C )Delhi
(D)Kanpur
83.The institution which calculates India's national income :
(A)Central StatisticalOrganisation
(B)Planning Commission
(C )National DevelopmentCouncil
(D)Finance Ministry
84.National Rural Employment Guarantee Act was passed in the year :
(A)2004
(B)2006
(C )2008
(D)2005
85.The architect of first five year plan of India is :
(A) R. Rangarajan
(B)K.M. Raj
(C ) J.C. Kumarappa
(D) P.C. Mahalanobis
86.The Cashewnut Research Station of Kerala is existed in :
(A)Panniyur
(B)Vellanikkara
(C )Anakkayam
(D)Pattambi
87.'Ashtamudi kayal' existed in the district of:
(A)Kottayam
(B)Ernamkulam
(C )Alappuzha
(D)Kollam
88. The District with least coastal plains
(A) Emamkulam
(B) Kollam
(C ) Kannur
(D) Kasaragode
89.The town 'Cheruthuruthy' situated on the River bank of :
(A) Kadalundi
(B) Bharathapuzha
(C ) Periyar
(D) Chaliyar
90.Name the agitation started in Kerala as a protest against the constitutional reforms of 1932 :
(A) Channar revolt
(B) Kayyur riot
(C ) Punnapra vayalar agitation
(D) Nivarthana agitation
91.The founder of 'Prathvaksha Raksha Daivasabha (PRDS) was :
(A) Ayyankali
(B) Pandit Karuppan
(C ) Kumara Guru
(D) Kumaranasan
92.Who conducted 'Yachana Yathra' from Trichur to Kasaragode to collect money for the programme of educational reforms ?
(A) Poikayil Yohannan
(B) Dr.Palpu
(C ) V.T. Vattatirippad
(D) Chattampi Swamikal
93.Identify the founder of 'Ananda Mahasabha' :
(A)Ayya Vaikundar
(B)Kumaranasan
(C ) Brahmanada Sivayogi
(D) Mannathu Padmanabhan
94.When did Father Kuriakose Elias Chavara was beatified by Pope John Paul II ?
(A)1986
(B)1976
(C )1982
(D)1988
95.The district which firstly declared as 'Smoke Free District' in India :
(A)Kottayam
(B)Kozhikkode
(C )Ernamkulam
(D)Alappuzha
96.Name the literary works which secured Odakkuzhal award in 2013 :
(A)Marupiravi
(B)ManushyanuOru Amukham
(C ) Aarachar
(D) Ammakku Oru Tharattu
97.The first Malayalam University of Kerala is setup in the District of:
(A)Kannur
(B)Kozhikode
(C )Palakkad
(D)Malappuram
98.How many digits consists in the unique idnumber of AADHAR ?
(A)11
(B)12
(C )10
(D)13
99.'Operation New Dawn' is the beginning of stability in :
(A)Afganisthan
(B)Iran
(C )Iraq
(D)Sudan
100.The Bodo language is spoken in the state of:
(A)Mizoram
(B)Tripura
(C )Arunachal Pradesh
(D)Assam
1. The term forging refers to :
(A)Plastic deformation
(B)Plastic deformation
(C )Stress deformation
(D)Strain reveling
2.A very difficult forgable material is :
(A)Maraging Steel
(B)Beryllium
(C )Magnesium alloy
(D)Nickel alloy
3.The highly elastic material is :
(A)Rubber
(B)Brass
(C )Glass
(D)Steel
4.Slow and progressive deformation is called :
(A)Resilience
(B)Malleability
(C )Creep
(D)Plasticity
5.When a material is subjected to cyclic periodic loading, the property' occurring is :
(A)Creep
(B)Fatigue
(C )Hardness
(D)Ductility
6.Hooke's Law states that:
(A)Stress x Strain = Constant
(B)Strain - Stress = Constant
(C )Stress = Constant Strain
(D)Stress + Strain = Constant
7.The process of forming new grain structure with reduced grain size when a metal is heated and deformed is called :
(A)Re-crystallisation
(B)Crystallisation
(C )Melting
(D)Deforming
8.Hot working temperature of steel is :
(A) 370-455°C
(B)760-925oC
(C ) 315°C
(D) 1100-1260’C
9.length of work piece is reduced by :
(A) Upsetting
(B) Fullering
(C ) Flattening
(D) Piercing
10.The cooling medium in normalising is :
(A) Water
(B) Oil
(C ) Air
(D) Artificial Coolants
11. Pure Iron melts at :
(A) 380oC
(B)760°C
(C ) 370oC
(D) 1539°C
12. Martensite is :
(A) Ductile
(B) Hard
(C ) Soft
(D) Brittle
13. Toughness is the ability to absorb :
(A) Impact
(B) Stresses
(C ) Load
(D) Heat
14.Heat treatment is done to change :
(A) Magnetic properties of metal
(B)Physical properties of metal
(C ) Mechanical properties of metal
(D) Electrical properties of metal
15.Which of the below is not a surface hardening process ?
(A) Nitriding
(B) Carburising
(C ) Cyaniding
(D) Annealing
16.A brittle material is :
(A) Mild steel
(C ) Low carbon steel
(B) Cast iron
(D) Plastic
17.Gamma Iron has the crystal structure of:
(A)bee.
(B) sc
(C ) hep
(D) fcc
18.The property by which a material absorbs energy without plastic deformation is :
(A) Resilience
(B) Hardness
(C ) Tensile Strength
(D) Toughness
19.In forging operation, work piece is usually subjected to :
(A)Tensile stress
(B)Shear stress
(C )Bending stress
(D)Compressive stress
20.Forging is a:
(i)Hot working operation
(ii)Cold working operation
(iii)Operation that involves pressing Of these statements :
(A)(i) is true
(B)(ii) and (iii) arc true
(C )(ii) is true
(D)(i) and (iii) are true
21.Hotdie forging is also known as :
(A)Roll forging
(B)Embossing
(C )Isothermal forging
(D)Precision forging
22.Thebody of Anvil is made of:
(A)Mild steel
(B)High carbon steel
(C )High speed steel
(D)Cast iron
23.In Anvil, hardie hole is used for :
(A)Bending rods of small diameters
(B)Hot punching operation
(C )Holding square shanks
(D) Cutting operation
24.In smithy operation, for general pick up work :
(A)Straight - lip fluted tong is used
(B)Flat tong is used
(C )Gad tong is used
(D)Ring tong is used
25.Necking down of work piece is done by :
(A)Swages
(B)Fullers
(C )Flatters
(D)Set hammer
26.Flux used in forge welding is :
(A)Calcined Borax
(B)Silica
(C )Nitric Oxide
(D)Calcium Carbonate
27.The method of preparing metal pieces for forge welding is called :
(A)Filling
(B)Jumping
(C )Reaming
(D)Scarfing
28.Drop forging comes under :
(A) Smith die forging
(B) Impression die forging
(C )Power forging
(D)Hand forging
29.Forging process for shaping round bars is called :
(A)Press forging
(B)Rotary forging
(C )Drop forging
(D)Billet
30.Iron with little or no carbon is called :
(A)Ferrite
(B)Sorbite
(C )Pearlite
(D)Martensite
31.The hardening response of steel to heat treatment is measured by :
(A)Brinell Test
(B)Jominy Test
(C )Morse Test
(D)Knoop Test
32.Which of the following metal is magnetic ?
(A)Aluminium
(B)Nickel
(C )Copper
(D)Magnesium
33.The metal used for die casting is :
(A)Copper
(B)Magnesium
(C )Zinc
(D)Lead
34.Metal with low melting point is :
(A)Lead
(B)Tin
(C )Zinc
(D)All the above
35.Galvanization is the process of coating :
(A)Tin
(B)Zinc
(C )Nickel
(D)Copper
36.Age hardening of non-ferrous metals is called :
(A) Case hardening
(B) Nitriding
(C ) Precipitation hardening
(D) Surface hardening
37.Dolomite is an important ore of:
(A)Lead
(B)Copper
(C )Magnesium
(D)Aluminium
38.The process of making blind holes is :
(A)Piercing
(B)Punching
(C )Blocking ,
(D) Bending
39.The process of hammering a heated bar into aligned die cavity is called :
(A)Press forging
(B)Drop forging
(C )Roll forging
(D)Rotary forging
40.Pitting of the forging surface is caused by :
(A)Slag
(B)Over heating
(C )Scale
(D)Low heating
41.The defect occurred in some alloy steel due to rapid cooling from forging temperature is:
(A)Creep
(B)Flakes
(C )Cracks
(D)Dents
42.The defect caused by misalignment between top and bottom forging dies is called :
(A) Fins and rags
(B) Die shift
(C ) Cracks
(D) Hair cracks
43.Simple way to remove scale from a forged part is :
(A) Using steam and compressed air
(B) Pickling
(C ) Tumbling process
(D) Blast cleaning
44.The Final treatment after forging is done to :
(A) Remove stresses
(B)Make the forged parts cool
(C ) Make the forging hard and tough
(D) To clear cracks
45.Flat forging of gear blanks are usually done by :
(A)Upsetting
(B)Downsetting
(C )Hammering
(D)Squeezing
46.During tempering, forged parts are cooled using :
(A)Oil
(B)Water
(C )Air
(D)Coolants
47.The mechanism used in presses for freeing the work piece from a die is called :
(A) Die set
(B) Knock out
(C ) Stroke '
(D) Stripper
48.The process of thinning the walls of a shell by forcing it through a die with a punch is called :
(A)Bending
(B)Rolling
(C )Re-drawing
(D)Ironing
49.Vacancy is :
(A)Point defect
(B)Line defect
(C )Surface defect
(D)Volume defect
50.Which one of the below is used to eliminate coarse grained structure :
(A)Annealing
(B)Tempering
(C )Cyaniding
(D)Normalising
51.Quenching is the process of:
(A) Rapid cooling of metals
(B) Slow cooling of metals
(C ) Intermediate cooling of metals
(D) Heating of metals
52.The ability of the material to resist deformation is :
(A) Ductility
(B) Creep
(C ) Fatigue strength
(D) Stiffness
53.Poisson's ratio is the ratio between :
(A) Strain to longitudinal stress
(B) Transverse strain to axial strain
(C ) Longitudinal stress to axial strain
(D) Longitudinal stress to strain
54.For ductile materials, factor of safety is :
(A)Ultimate stress/Design stress
(B)Induced stress/Design stress
(C )Yield stress/ Design stress
(D)Design stress/ Yield stress
55.Carbon content in cast iron is :
(A)3.2-5.2%
(B)2.1-4.5%
(C )8.3-9.2%
(D)1.2-2%
56.The hardest known material is :
(A)High speed steel
(B)Carbides
(C )Ceramics
(D)Diamond
57.The ability of a material that can be drawn into thin wire is :
(A)Hardness
(B)Tensile strength
(C )Creep
(D)Ductility
58.Alloying of vanadium increases :
(A)Toughness and wear resistance of steel
(B)Hardenability of steel
(C )Oxidation resistance of steel
(D)Corrosion resistance
59.The purest iron is :
(A) Wrought iron
(B) Pig iron
(C ) Electrolytic iron
(D) Cast iron
60.TTT stands for :
(A)Time Temperature Transformation
(B)Temperature Toughness Time
(C )Toughness Transformation Time
(D)Total Time Transformation
61.The welding accompanied by the application of pressure is :
(A)Gas welding
(B)Fusion welding
(C )Plastic welding
(D)Arc welding
62.The change of state of alloys due to variation in temperature and concentration is represented by:
(A) Phase rule
(B) Phase diagram
(C ) Equilibrium diagram
(D) Graphs
63.The fuel used in hearth is :
(A)Coke .
(B)Wood
(C )Methane
(D)Oil
64.The forging temperature of wrought iron is :
(A)800-1150°C
(B)900- 1300°C
(C )750-1250°C
(D)400-500°C
65.An English anvil has :
(A)Two beaks
(B)No beaks
(C )Three beaks
(D)One beak
66.Swage block is made of:
(A)Mild steel
(B)HSS
(C )Cast iron
(D)High carbon steel
67.Open mouth tong is used to hold :
(A)Heavier stock
(B)Round stock
(C )Square stock
(D)Ductilestock
68.Cold chisel has a cutting angle of:
(A)45°
(B)30°
(C )30°
(D)60°
69.Necking down of a work is done by :
(A)Set hammer
(B)Punches
(C )Fullers
(D)Squarepunch
70.Before scarf welding the ends of work pieces are :
(A)Made square
(B)Rounded
(C )Filed
(D)Cooled
71.The forging machine working by pressure are called :
(A)Hammers
(B)Pressure hammers
(C )Presses
(D)Ramming machine
72.Thecommon mass of Anvil is about:
(A)150 kg
(B) 200 kg
(C )100 kg
(D)250 kg
73.Thevice commonly used in smithy is :
(A)Hand vice
(B) Bench vice
(C )Carpenter's vice
(D)Leg vice
74.Theangle of double cut file is :
(A)60° and 80°
(B) 60° and 70°
(C )80o and 50°
(D)45° and 60°
75.Thematerial for hacksaw blade is :
(A)HCS
(B) HSS
(C )Tool steel
(D)Vanadium steel
76.Prick punch has an approximate included angle of :
(A)30°
(B)90°
(C )35°
(D) 40°
77.Least count of steelrule is :
(A)0.5 mm
(B)0.05 mm
(C )0.25 mm
(D)0.1 mm
78.For smithy operation an anvil used to hold small work piece is :
(A)Bench vice
(B)Hand vice
(C )Bick iron
(D)Leg vice
79.Tool used to level and finish the comers of flat surfaces is :
(A)Set hammer
(B)Fuller
(C )Drift
(D)Swage
80.Effective length of a file is the distance from :
(A)Point to the heel
(B)End of handle to thepoint
(C )Tang to edge
(D)Tang to point
81.The River which originated from the "Gaymukh" cave of Himalaya :
(A)Ganga
(B)Brahmaputhra
(C )Sindhu
(D)Tapti
82.The Indian Museum situated in the place of:
(A)Kolkatta
(B)Mumbai
(C )Delhi
(D)Kanpur
83.The institution which calculates India's national income :
(A)Central StatisticalOrganisation
(B)Planning Commission
(C )National DevelopmentCouncil
(D)Finance Ministry
84.National Rural Employment Guarantee Act was passed in the year :
(A)2004
(B)2006
(C )2008
(D)2005
85.The architect of first five year plan of India is :
(A) R. Rangarajan
(B)K.M. Raj
(C ) J.C. Kumarappa
(D) P.C. Mahalanobis
86.The Cashewnut Research Station of Kerala is existed in :
(A)Panniyur
(B)Vellanikkara
(C )Anakkayam
(D)Pattambi
87.'Ashtamudi kayal' existed in the district of:
(A)Kottayam
(B)Ernamkulam
(C )Alappuzha
(D)Kollam
88. The District with least coastal plains
(A) Emamkulam
(B) Kollam
(C ) Kannur
(D) Kasaragode
89.The town 'Cheruthuruthy' situated on the River bank of :
(A) Kadalundi
(B) Bharathapuzha
(C ) Periyar
(D) Chaliyar
90.Name the agitation started in Kerala as a protest against the constitutional reforms of 1932 :
(A) Channar revolt
(B) Kayyur riot
(C ) Punnapra vayalar agitation
(D) Nivarthana agitation
91.The founder of 'Prathvaksha Raksha Daivasabha (PRDS) was :
(A) Ayyankali
(B) Pandit Karuppan
(C ) Kumara Guru
(D) Kumaranasan
92.Who conducted 'Yachana Yathra' from Trichur to Kasaragode to collect money for the programme of educational reforms ?
(A) Poikayil Yohannan
(B) Dr.Palpu
(C ) V.T. Vattatirippad
(D) Chattampi Swamikal
93.Identify the founder of 'Ananda Mahasabha' :
(A)Ayya Vaikundar
(B)Kumaranasan
(C ) Brahmanada Sivayogi
(D) Mannathu Padmanabhan
94.When did Father Kuriakose Elias Chavara was beatified by Pope John Paul II ?
(A)1986
(B)1976
(C )1982
(D)1988
95.The district which firstly declared as 'Smoke Free District' in India :
(A)Kottayam
(B)Kozhikkode
(C )Ernamkulam
(D)Alappuzha
96.Name the literary works which secured Odakkuzhal award in 2013 :
(A)Marupiravi
(B)ManushyanuOru Amukham
(C ) Aarachar
(D) Ammakku Oru Tharattu
97.The first Malayalam University of Kerala is setup in the District of:
(A)Kannur
(B)Kozhikode
(C )Palakkad
(D)Malappuram
98.How many digits consists in the unique idnumber of AADHAR ?
(A)11
(B)12
(C )10
(D)13
99.'Operation New Dawn' is the beginning of stability in :
(A)Afganisthan
(B)Iran
(C )Iraq
(D)Sudan
100.The Bodo language is spoken in the state of:
(A)Mizoram
(B)Tripura
(C )Arunachal Pradesh
(D)Assam