A High Input Voltage Three-Phase ZVZCS DC-DC Converter with Vin /3 Voltage Stress on Primary Switches
Abstract
A high-voltage three-phase ZVZCS dc-dc converterwith low voltage stress is presented in this paper. The voltagestress on the primary switches is only one-third of the inputvoltage. By using the phase shift pulsewidth modulation (PWM)and secondary snubber, four of the six primary switches areoperating with zero-voltage switching (ZVS) and two of them areoperating with zero-current switching (ZCS), in order to reducethe switch ....etc

[:=Read Full Message Here=:]

circuit diagram of over under voltage protection of electrical applications ....etc

[:=Read Full Message Here=:]

Introduction

An inverter is an electrical device that converts direct current (DC) to alternating current (AC); the converted AC can be at any required voltage and frequency with the use of appropriate transformers, switching, and control circuits.
Static inverters have no moving parts and are used in a wide range of applications, from small switching power supplies in computers, to large electric utility high-voltage direct current applications that transport bulk power. Inverters are co ....etc

[:=Read Full Message Here=:]

1. Design and Implementation of Microcontroller based PWM technique for Sine wave Inverter
2. A novel DC-AC Single Phase Resonant Inverter using soft switching boost converter
3. Study on Dual-Loop Grid Current Control Scheme for Grid-Connected Inverter with an LCL-Filter
4. ZVS H-bridge Inverter using Soft Switching Boost Converter
5. A Novel Hybrid Modulation Scheme for an Isolated High-Frequency-Link Fuel Cell Inverter
6. ZVS Resonant DC-link Inverter using Soft Switching Boost Converter
7. Comparison of Z-Source Inverter and Traditi ....etc

[:=Read Full Message Here=:]

PRESENTED By
SUDHAKAR AKKI


SPACE VECTOR MODULATION FOR TWO LEG INVERTERS
INTRODUCTION
• Semiconductor switches mainly determine the overall price of power converters.
• The main objective of this project is to prove 2leg inverters are the best option for low power applications for getting the good performance.
• Two leg inverter produces the square wave or quasi-square wave. but low power applications allow the two leg inverter output.
• In many industrial applications, it is often required to v ....etc

[:=Read Full Message Here=:]

name dinesh
mini projet report
Voltage source inverters (VSI) have been widely used in uninterruptible power supplies, unified power flow controllers or unified power quality conditioners, and distributed generation systems (DGS). VSIs are inherently efficient, compact, and economical devices used to control power flow and provide quality supply. VSIs can be classified as voltage-controlled VSIs (VCVSIs) and current-controlled VSIs (CCVSIs), depending on their control mechanism. In this paper, a detailed comparison of VCVSIs and CCVSIs for DG ....etc

[:=Read Full Message Here=:]

circuit diagram of over under voltage protectn of electrical applicatins using lm324 ....etc

[:=Read Full Message Here=:]

i want over voltage and under voltage protection doc for mini project please help me ....etc

[:=Read Full Message Here=:]

Pulse Based Dead Time Compensator for PWM Voltage Inverters



I. Introduction
The state of the art in motor control provides an adjustable
voltage and frequency to the terminals of the motor
through a pulse width modulated (PWM) voltage source inverter
drive. As the power devices change switching states,
a dead time exists. Although the dead time is short, it
causes deviations from the desired fundamental output voltage.
While each deviation does not appreciably affect the
fundamental voltage, the ac ....etc

[:=Read Full Message Here=:]

4.6 NUETRAL POINT CLAMPED (NPC) INVERTERS


Known as three-level inverters

Problem of 2-level inverter in high-power applications
High DC page link voltage requires series connection of devices  difficulty in dynamic voltage sharing during switching

Solved using NPC inverter or multilevel inverter

NPC inverter circuit


NPC (3)

DC page link capacitor split to create neutral point 0

Q11, Q14 : main devices (2-level inverter)

Q12, Q13 : auxiliary devices – clamp output potential to ne ....etc

[:=Read Full Message Here=:]