This article is presented by:
D. Chandrasekharam
Department of Earth Sciences
Indian Institute of Technology
Bombay 400076, India
GEOTHERMAL ENERGY RESOURCES OF INDIA: COUNTRY UPDATE

ABSTRACT
All the geothermal provinces of India are located in areas with high heat flow and geothermal gradients. The heat flow and thermal gradient values vary from 75–468 mW/m2 and 59–234°C respectively. Additional exploration studies and reservoir modelling have ....etc

[:=Read Full Message Here=:]

CONSTRUCTION SAFETY CLIMATE
IN DEVELOPING COUNTRY
BIKARAMA PRASAD YADAV
SENIOR HSE- MANAGER
SOMA ENTERPRISES LTD
DMRC PROJECT
Email - [email protected]
Safety in the construction industry has always
been a major issue. Wherever reliable records are
available, construction is found to be one of the
most dangerous on safety and health criteria,
particularly in developing countries. Though much
improvement in construction safety has been
achieved, the industry still continues to lag behind
most other industries with regard to ....etc

[:=Read Full Message Here=:]

INTRODUCTION

From its origin more than 25 years ago, Ethernet has evolved to meet the increasing demands of packet-switched networks. Due to its proven low implementation cost, its known reliability, and relative simplicity of installation and maintenance, its popularity has grown to the point that today nearly all traffic on the Internet originates or ends with an Ethernet connection. Further, as the demand for ever-faster network speeds has grown, Ethernet has been adapted to handle these higher speeds and the concomi ....etc

[:=Read Full Message Here=:]

1.The angle between two curved lines is known as :
(A)Spherical angle
(B) Obtuse angle
(C ) Acute angle
(D) Deflection angle

2.Which of the following is the classification based upon the system of surveying ?
(A)Chain surveying
(B)Triangulation surveying
(C )City surveying
(D)Mine surveying

3.The survey that does not deal with mapping of large water bodies is :
(A)Hydrographic Survey
(B)Navigation Survey
(C )Marine Survey
(D)Cadastral Survey

4.During the office work, surveyor does :
(A)Design of struct ....etc

[:=Read Full Message Here=:]

i want to know the result of west bengal state lottery dewali bumper result 28.10.2014 top ten ....etc

[:=Read Full Message Here=:]

155/2015
Maximum : 100 marks
Time : 1 hour and 15 minutes

1.The maximum twisting moment a shaft can resist, is the product of the 
permissible shear stress and:
(A)Moment of inertia
(B) Polar moment of inertia
(C ) Polar modulus
(D) Modulus of rigidly

2.A beam of length L is pinned at both ends and is subjected to a 
concentrated bending couple of moment M at its centre. The maximum bending 
moment in the beam is :
(A)ML/2
(B)M
(C )M/3
(D)M/2

3.In plastic analysis, the shape factor for a triangular ....etc

[:=Read Full Message Here=:]

Ten Tough Interview Questions and Ten Great Answers
The following are some of the most difficult questions you will face in the course of your job interviews. Some questions may seem rather simple on the surface--such as Tell me about yourself--but these questions can have a variety of answers. The more open-ended the question, the wider the variation in the answers. Once you have become practiced in your interviewing skills, you will find that you can use almost any question as a launching pad for a particular top ....etc

[:=Read Full Message Here=:]

diwali bumper west bengal state lottery draw on 28/10/2014 result need.
....etc

[:=Read Full Message Here=:]

Hi,
I would like to know about top 10 MNC companies in the world... Kindly send me please...




Thanks,
Jeni ....etc

[:=Read Full Message Here=:]

STUDYING THE PROCUREMENT MANAGEMENT SYSTEM IN CROSS COUNTRY NATURAL GAS PIPELINE PROJECTS & SUGGEST TECHNIQUE FOR IMPROVE THE PROCESS
Executive summary
The project title is “Studying the procurement management system in Cross Country Natural Gas pipeline projects & suggest techniques to improve the process”. This report is divided in five main parts. First is introduction about company GSPL and industry in which GSPL is working. Second tells about the different project activities in a project. Third chapt ....etc

[:=Read Full Message Here=:]