Abstract:
A maximum power point tracking algorithm for single-stage converters connecting
photovoltaic panels to a single-phase grid is presented in this paper. The algorithm is
based on the processing of current and voltage low-frequency oscillations introduced in the
PV panels by the single-phase utility grid. The algorithm has been developed to allow an
array of PV modules to be connected to the grid by using a single-stage converter. This
simple structure yields higher efficiency and reliability when compared with standard so ....etc

[:=Read Full Message Here=:]

ABSTRACT
Laser assisted machining (LAM) can improve the machinability of materials by locally
heating the material prior to its removal. The work presented here is a study of the laser assisted machining of Inconel 718 (NiCr19FeNb at 46 HRc) with ceramic insert. The tests have shown a reduction in the cutting force, and have highlighted the impact of laser assistance on the integrity surface (roughness, appearance, residual stress) and the tool life.
Also , It not only efficiently red ....etc

[:=Read Full Message Here=:]

i want a ppt for this title as posible as early pleas can you provide
....etc

[:=Read Full Message Here=:]

SEMINAR REPORT ON SINGLE CRYSTAL CASTING OF HPTR BLADE FOR AL-31FP ENGINE

Presented by,
Dillip Kumar Das Mohapatra
Mechanical Engg.
Regd No.-0721101016
7th Semester
VSSUT,BURLA





SINGLE CRYSTAL HP TURBINE BLADE

HPTR blades are hollow and of single crystal structure. This enhance creep resistance, thermal fatigue and hence enhances the life of the blade.
the shape of the turbine blade has a larger relative thickness and curvature compare to compressor blade




Turbine blade ....etc

[:=Read Full Message Here=:]

Study of High Temperature Crack Initiation in Single Crystal


Because of their excellent high temperature characteristics, Ni-based single-crystal alloys are used in applications where operating temperatures exceed 900ºC. The initiation of cracks under these conditions is generally associated with micro-scale porosities (typically between 10 and 20 microns). A rate-dependent crystallographic constitutive model in conjunction with a mass diffusion model has been used to study crack initiation in single crystal nickel-base superalloys ....etc

[:=Read Full Message Here=:]

Because of their excellent high temperature characteristics, Ni-based single-crystal alloys are used in applications where operating temperatures exceed 900ºC. The initiation of cracks under these conditions is generally associated with micro-scale porosities (typically between 10 and 20 microns). A rate-dependent crystallographic constitutive model in conjunction with a mass diffusion model has been used to study crack initiation in single crystal nickel-base superalloys, exposed to an oxidizing environment and subjected to ....etc

[:=Read Full Message Here=:]

I need a ppt of single crystal growth technique ....etc

[:=Read Full Message Here=:]

I want deep knowledge about single crystal casting with relevent pictures and applications ....etc

[:=Read Full Message Here=:]

1. Transformer protection panel
2. Working Model of maglev
3. Maximum power point Tracking
4. Motorised wheel Chair
5. Controller of Electrical Vehicale
6. Deregulation of Energy Sector
7. Cathodic protection
8. Radial Feeder protection
9. PLC Based System
10. Numerical Relay
11. Measurement of electrical parameters
12. Variable Frequency Drive
13. 3 Phase Analayzer
14. Modeling and simulation of Congestion management in transmission sector of deregulated electricity market.
15. Electrical Bicycle
16. Survey of Industries in sura ....etc

[:=Read Full Message Here=:]

ABSTRACT

This paper presents a new 3-level, single-phase, pulse width modulated (PWM), boost-integrated acto- dc series resonant converter (SRC) with high frequency transformer isolation. This converter uses a new gating scheme suitable for integrating boost converter and PWM 3-level dc-to-dc SRC converter with above resonance operation. Principle of operation and different operating modes are presented with analysis. Based on the analysis design example of a 1 HP, 280 V, 50 kHz ac-to-dc series resonant conv ....etc

[:=Read Full Message Here=:]