May I get the detailed report for this project ....etc

[:=Read Full Message Here=:]

The Trojan Horse programs and computer viruses in the real world, cannot be treated as the realizations of turing machines. In this article, the actions of Trojan Horses and viruses in the real world are considered and a minimal framework is described for their modelling for a better understanding. biological metaphors and some similar conventional approaches are shown to be inadequate. Some suggestions for constructing virally-resistant systems are also put forward.
Computer viruses also mimic the behaviour of biological pests. The facili ....etc

[:=Read Full Message Here=:]

DESIGN AND MODELLING OF CUPOLA

DONE BY
CEASE JUNIOR
FIJO GEORGE
FOUZIYA C M
HAREESH MOHANAN
JESBIN JOSE
JIBIN JOSEPH

CONTENTS
OBJECTIVE OF PROJECT
INTRODUCTION
CONSTRUCTION
CUPOLA OPERATIONS
ADVANTAGES AND LIMITATIONS
DESIGN CONSIDERATIONS
DESIGN
FABRICATION DETAILS
BIBLIOGRAPHY

OBJECTIVE OF PROJECT
TO DESIGN AND FABRICATE A MODEL OF SIZE 2 CUPOLA IN THE RATIO 1:2
FURNACES
FURNACES ARE OF TWO TYPES
1. BLAST FURNACES
2. FOUNDRY FURNACES
Blast furnaces performs basic melt ....etc

[:=Read Full Message Here=:]

i want modelling and thermal analysis of diesel engine piston with catia and ansys pdf material ....etc

[:=Read Full Message Here=:]

Prepared by:
MUHAMMAD NASIRUDDIN MAHYUDDIN


Introduction

The first step is to determine tha control. The purpose of the control law is to allow us to assign a set of pole locations for the closed-loop system that will correspond to satisfactory dynamic response in terms of rise time and other measure of transient response.
Then, secondly, we show how to introduce the reference input with full-state feedback. We describe the process of finding the poles for good design. In the second step, If t ....etc

[:=Read Full Message Here=:]

Abstract –
This paper presents the work that is beingdone as a part of the ByFault project (Brite/Euramprojet finaced by the European Community):manufacturing, modelling and simulation of aSuperconducting Hybrid Fault Current Limiter(SHFCL). The SHFCL is based on a variableimpedance transformer: primary winding is in serieswith the protected line and several secondaries areshort-circuited by superconducting elements. Thistopology has been modelled using 2-D and 3-D finiteelements, and some useful formulation to simulate thebehaviour ....etc

[:=Read Full Message Here=:]

Governing Control system
• Speed Sensing :Mechanical (Fly ball type), Hydraulic (Pump), Electric (toothed Wheel pick up)
• MW Transducer for Power
• Processing : Hydro‐mechanical, Electrohydraulic, Digital Electro‐hydraulic
• Amplification: Hydraulic amplifiers in various stages
• Actuation: Hydraulic Servomotor
Control Requirements
• Start‐up: To control machine speed for proper synchronization
• Normal Operation: To Control MW and To participate in the control of system frequency
....etc

[:=Read Full Message Here=:]

Presented By:
H-L Lin1, T Chou2, and C-P Chou2
Department of Vehicle Engineering, Army Academy R.O.C
Abstract:
Many parameters affect the quality of the resistance spot welding (RSW) process. It is not easy to obtain optimal parameters of the RSW process in the automobile industry. Conventionally, the Taguchi method has been widely used in engineering; however, with this method the desired results can only be obtained with the use of very discrete control factors, thus leading to uncertainty about the real optimum. In the process ....etc

[:=Read Full Message Here=:]

Abstract

In paper the fundamental question about optimal interaction between the controlling stimuli generated by the active (powered) and the passive (unpowered) drives of the robotic systems have been studied. A mathematical statement of the problem has been proposed that is suitable to study this question for the semi-passively actuated n-degree-of-freedom robotic systems. The problem is formulated as an optimal control problem for n-degree-of-freedom mechanical system models a semi-passively actuated robot. We take into account the inter ....etc

[:=Read Full Message Here=:]

can anyone provide me with information on topic Microstructural modelling of branched block and linear block polyolefins ....etc

[:=Read Full Message Here=:]