SIR i am an M.tech student please help me to get the design based seminar reports
especially i need the seminar report on this

ANALYSIS OF RESIDUAL STRESSES IN MAIN CRANKSHAFT BEARINGS AFTER INDUCTION SURFACE
so please help me to find it and if u know any then please do mail it to
any one of this mail id

[email protected]

[email protected]

[email protected] its very very urgent ....etc

[:=Read Full Message Here=:]

Hello,
Give me complete information regarding Bearings.
Thank you. ....etc

[:=Read Full Message Here=:]

By,
PRADEEP.T.P

Introduction

Copper , Aluminium and Lead-common journal bearing materials.
Bronze and Brass- Copper based alloys.
Zamacs - Zinc based alloys.
Duralumines - Aluminium based alloys.
White metals- Tin lead based alloys.
Present study- Tribological and mechanical properties of these journal bearings materials.

Tribology

Science and technology of interacting surfaces in relative motion and of related sub and practices.
Deals with ....etc

[:=Read Full Message Here=:]

ACTIVE MAGNETIC BEARINGS (AMB)
A magnetic bearing is a bearing which supports a load using magnetic levitation. Magnetic bearings support moving machinery without physical contact, for example, they can levitate a rotating shaft and permit relative motion without friction or wear. In active magnetic bearings (AMB) a stable equilibrium is achieved by means of one or more control loops. The use of control loop for maintaining the gap between the shaft and bearing differentiate the active magnetic bearings (AMB) from pa ....etc

[:=Read Full Message Here=:]

Abstract

Designing Magnetic Bearings

• Magnetic bearings are used to levitate flywheels so they can spin at high speeds without mechanical contact.
• The design of a bearing set to control a flywheel weighing 5100 lbs and spinning at 15,000 revolutions per minute was described in the paper, “Permanent Magnet Bias, Homopolar Magnetic Bearings for a 130 kW-hr Composite Flywheel,” by B. Murphy, H. Ouroua, M. Caprio, and J.Herbst.
• The paper was presented at the Ninth International Symposium on M ....etc

[:=Read Full Message Here=:]

....etc

[:=Read Full Message Here=:]

Presented by:
HIREN R PATEL


-: ABSTRACT:-
Bearings are valuable.... until they go bad, and then they are worthless. But the definition of Bad Condition of Bearing is not standardized yet. To quickly discover what bearings may be salvaged, we offers positive testing machine. Because “A Bearing Saved is a Bearing Earned”. We tried to compare the bearings on ideal and defective condition on Sound and Vibration factor. For Sound we used microphone and for Vibrations we implemented piezoelectric sensor. Instea ....etc

[:=Read Full Message Here=:]

NEED AND IMPORTANCE OF THE STUDY
The present study is taken to examine the Social Security and Welfare Measures which are implementing in HMT Bearings, a public sector undertaking.
Effective implementation of welfare activities as well as security measures is very important for successful acquisition, utilization, improvement & presentation of Human Resources.
SOCIAL SECURITY AND WELFARE MEASURES ARE TO BE STUDIED TO:
1. Succeeded in the fast changing environment.
2. Prepare & respond to the increasing pr ....etc

[:=Read Full Message Here=:]

ANALYSIS OF RESIDUAL STRESSES IN MAIN CRANKSHAFT BEARINGS AFTER INDUCTION SURFACE HARDENING AND FINISH GRINDING


INDUCTION SURFACE HARDENING

ADVANTAGES

¢ Short Heat Treatment Times

¢ Good Repeatability

¢ Hardened Layer Quality

¢ Small or Negligible Subsequent Distortion

¢ Minimum Subsequent Product Surface Oxidation

¢ Good Possibilities for Automation

SURFACE INTEGRITY AND ITS LEVELS

Scientific discipline providing an integral assessment of the surface and surface layers
Measurement of Roughness ....etc

[:=Read Full Message Here=:]

Hi sir...this is Raghavendra studying in final semester BE.I need complete seminar report along with power point presentation on Air bearing topic.Please send me the reports as early as possible.My email id is [email protected].

Thank you. ....etc

[:=Read Full Message Here=:]