1.Auxiliary theodolite station near an inaccessiblemaintriangulation station :
(A) change point(B)bench markbench mark
(C ) satellite station(D)none of these

2.The maximum and minimum number of steps in a flight is equal to:
(A)12 and 1(B)18 and 2
(C ) 24 and 3(D)12 and 312 and 3

3.What is the angle of intersection of a contour and a ridge line?
(A) 0°(B)90°
(C ) 180°(D)270°

4.If stiffness of a metal increases its ductility:
(A) Decreases(B)Increases
(C ) Remains same(D)None of theseNone of these

5.T ....etc

[:=Read Full Message Here=:]

Please sent me research questionnaire on green marketing and its impact on consumer ....etc

[:=Read Full Message Here=:]

1.One hectare equals : (A)100 m2
(C )10,000 m2
(B)1000 m2
(D)100000 m2

2.Chain surveying is most suitable for:
(A) forest area(B) hill area
(C ) undulating area(D) flat surface

3.If a measuring tape is too long as compared to standard length, the error will be :
(A)Accidental error(B)Instrumental error
(C )Personal errorPersonal error(D)Natural errorNatural error

4.The boundary of water of a still lake represents :
(A)Level surface(B)Horizontal surfaceHorizontal surface
(C )Contour lineContour line(D)Conca ....etc

[:=Read Full Message Here=:]

Present project is designed using 8051 microcontroller to avoid railway accidents happening at unattended railway gates, if implemented in spirit. This project utilizes two powerful IR transmitters and two receivers; one pair of transmitter and receiver is fixed at up side (from where the train comes) at a level higher than a human being in exact alignment and similarly the other pair is fixed at down side of the train direction. Sensor activation time is so adjusted by calculating the time taken at a certain speed to cross at least one compart ....etc

[:=Read Full Message Here=:]

1.The height of a telescopic metric staff :
(A)3 m
(B)4 m
(C )5 m
(D)3.5 m

2.Instrument for drawing rays in plane table survey :
(A)U - frame
(B)troughcompass
(C )spirit level
(D)alidade

3.The point where two readings are taken in leveling :
(A)Back sight
(B)Fore sight
(C )Change point
(D)Intermediate sight

4.The Scale used in theodolite :
(A)Plain scale
(B)Diagonal scale
(C )Comparative scale
(D)Vernier scale

5.In metric chain one metre length is divided into :
(A)20 links
(B)Slinks
(C )10 li ....etc

[:=Read Full Message Here=:]

53/2015
Maximum : 100 marks
Time : 1 hour and 15 minutes

1.The whole circle bearing of a line is 283° 20', its corresponding quadrantal bearing is :
(A)N 77° 20'E
(B) N 76° 20' W
(C ) S 76° 40' E
(D) N 76° 40' W

2.During the measurement, variable tension in tape results--------error.
(A)Cumulative
(B) Compensative
(C ) Instrumental
(D) None of the above

3.The Gunters chain is---------------ft. long and its link length is---------ft.
(A)66 ft long and 0.66 ft ,
(B)33 ft long and .33 ft
(C )33 ft lo ....etc

[:=Read Full Message Here=:]

FLYING WINDMILLS OR FLYING ELECTRIC GENERATOR (FEG) TECHNOLOGY


PRESENTED BY: NABEEL.SUBER.KUNJU
Batch EEE-7
Sree Buddha College Of Engineering
Pattoor



INTRODUCTION
FEGs are proposed to harness kinetic energy in the powerful, persistent high altitude winds.

It is tethered to the earth and churning out electricity from the jet streams.

This energy source is well suited for rural or low populated areas.

FEG technology is just cheaper, cleaner and can provide mor ....etc

[:=Read Full Message Here=:]

SLIVER GENERATION REDUCTION IN TRIMMING OF ALUMINUM
Seminar
Presented by
VIVEK ASHWIN
DEPARTMENT OF MECHANICAL ENGINEERING
N S S COLLEGE OF ENGINEERING
PALAKKAD-678008, KERALA.

SYNOPSIS

Aluminum auto body sheets produce appreciable amounts of slivers during trimming operations when trimmed with dies conventionally designed for steel sheets. The slivers can be carried through downstream processes and cause damage to the surface of formed parts resulting in costly manual repair. T ....etc

[:=Read Full Message Here=:]

I NEED A MATLAB code for multihop cognitive radios ....etc

[:=Read Full Message Here=:]

INTRODUCTION


The implementation of Just In Time Manufacturing management philosophy in industries like the automobile industry can bring about a see saw change in both quality & quantity since in a JIT system, underutilized (excess) capacity is used instead of buffer inventories to hedge against problems that may arise. This seminar gives an over view of the JUST IN TIME technique by considering the TOYOTA PRODUCTION SYSTEM in detail

IT is a management philosophy that strives to eliminate sources of manufacturing waste by producing the ....etc

[:=Read Full Message Here=:]

Flying Windmills or Flying Electric Generator (FEG) technology
Presented By:
BY,
G.SHRAVANI
06K81A0213



ABSTRACT
High Altitude Wind Power uses flying electric generator (FEG) technology in the form of what have been more popularly called flying windmills, is a proposed renewable energy project over rural or low-populated areas, to produce around 12,000 MW of electricity with only 600 well clustered rotorcraft kites that use only simple autogyro physics to generate far mor ....etc

[:=Read Full Message Here=:]

PRESENTED BY
UJJWAL KUMAR JHA


Introduction
Radar is an acronym for Radio Detection And Ranging. A radar is an electro-magnetic device capable of transmitting a electro-magnetic wave near 1 Ghz, receiver back a reflection from a target and based on the characteristics of the returned signal determine things about the target. Radars have become indispensable in several major fields of research and in commerce. The Federal Aviation Agency (FAA) makes extensive use of radars not only to track aircraft, but to ma ....etc

[:=Read Full Message Here=:]