LABORATORY INVESTIGATION OF LOW SWIRL INJECTOR FOR LEAN PRE-MIXED GAS TURBINES


SEMINAR REPORT Submitted by
KIRAN .G.
S7M2
ROLL NO-30
Department Of Mechanical Engineering
College of Engineering, Thiruvananthapuram – 16
OCTOBER 2010




ABSTRACT

Laboratory experiments have been conducted to investigate the fuel effects on the

turbulent premixed flames produced by a gas turbine low-swirl injector (LSI). The

lean-blow off li ....etc

[:=Read Full Message Here=:]

Binary and Mixed-Integer Programming

The general branch and bound approach described in the previous chapter can be customized forspecial situations. This chapter addresses two special situations:
when all of the variables are binary (known as “Binary Integer Programming” or BIP),when some or all of the variables are integer-valued and the objective function and all of the constraints are linear (known as “Mixed Integer Programming”, MIP, or “MixedInteger Linear Programming”, MILP).
Binary Integer Programming
I ....etc

[:=Read Full Message Here=:]

Hi am Mike i would like to get details on ppr pipes feasibility study ..My friend Justin said ppr pipes feasibility study will be available here and now i am living in kenya and i last studied in the college/school university of nairobi and now am doing a final project i need help on ppr feasibility study report and related data. ....etc

[:=Read Full Message Here=:]

Hello 
I want an introduction about


mixed traffic control behavior continuously reinforced concrete pavement 
Please answre me  ....etc

[:=Read Full Message Here=:]

1. Petrochemical level indicator and controller for automation of cotton purification industries using PSOC Mixed Signal Array
2. Implementation of I2C protocol for EEPROM interfacing using PSOC Mixed Signal Array
3. Proximity Sensor based intelligent Security system using PSoC mixed signal array
4. Auto turn off water pump with four different time slots using PSOC Mixed Signal Array
5. Implementing loopback I2Cprotocol using PSOC Mixed Signal Array
6. Interfacing SPI EEPROM to PSoC mixed signal array
7. Capsense based Industrial applianc ....etc

[:=Read Full Message Here=:]

Low power and high speed multiplication design through mixed number representation


Apeksha Reddy, VI Sem, SDMCET, Dharwad
Ashroo M Das, VI Sem, SDMCET, Dharwad



Contents

INTRODUCTION
THE ALGORITHM AND ITS VLSI ARCHITECTURE
CONVERSION FROM TWO’S COMPLEMENT TO SM NOTATION
RADIX-4 BOOTH’S ALGORITHM
SPEEDING UP THE PP ACCUMULATION
CONVERTING THE RB NUMBER INTO TWO’S COMPLEMENT NUMBER
CONCLUSION
REFRENCES
ACKNOWLEDGEMENT


What is a multiplication ?
How is multiplication done?
With what s ....etc

[:=Read Full Message Here=:]

ABSTRACT
Metals and plastics waste materials create serious environmental problems, mainly owing to the inconsistency of the wastes streams. The purpose of this paper is to evaluate the possibility of using mixed iron filings and granulated plastic waste materials simultaneously to partially substitute the fine aggregate in concrete composites. Type I Portland cement was mixed with the aggregates to produce the concrete composites. Three weight fractions (30, 40, and 50%) of iron filings waste aggregate were used with 5% of ....etc

[:=Read Full Message Here=:]

Ductile Mixed-mode Fracture Criterion Development and Crack Growth Simulations




Stable tearing crack growth (slow ductile growth of a macroscopic crack in a load-bearing structure) is an important fracture failure process in ductile materials (e.g. metals) and usually precedes the final catastrophic failure of a structure. In recent years, there has been a growing demand for a simulation-based structural design and evaluation methodology that takes into account the stable tearing crack growth process. Within such a methodology, two too ....etc

[:=Read Full Message Here=:]

Stable tearing crack growth (slow ductile growth of a macroscopic crack in a load-bearing structure) is an important fracture failure process in ductile materials (e.g. metals) and usually precedes the final catastrophic failure of a structure. In recent years, there has been a growing demand for a simulation-based structural design and evaluation methodology that takes into account the stable tearing crack growth process. Within such a methodology, two tools must be available: (1) an efficient computer simulation code that can handle the kinem ....etc

[:=Read Full Message Here=:]

i need full paper of this topic ....etc

[:=Read Full Message Here=:]