magine if killing flu viruses and other microbes were as simple as turning on a light.

Exposing a unique surface coating to light may in fact hold the key to protecting you from virtually all viruses and bacteria, including the feared avian flu.

Laboratory testing of a novel, permanent nano-coating, developed in collaboration by researchers at North Carolina State University College of Textiles and Emory University School of Medicine, has been shown to kill or inactivate most viruses and bacteria when exposed to visible light. Early tes ....etc

[:=Read Full Message Here=:]

i am going to do prokject in this topic.please send me the detailed view of this topic and report with suitable diagram in wor format and power point format ....etc

[:=Read Full Message Here=:]

On the macro scale, feedback control is routinely applied to improve performance and enable new tasks in complex and uncertain systems operating in noisy environments. Our lab has focused on applying feedback control ideas to systems on the micro scale. Here we show how control methods can improve existing performance in the UCLA lab-on-a-chip electrowetting system and can create entirely new capabilities in our 'micro fluidic tweezers' cell steering devices.In the Electro-Wetting-On-Dielectric (EWOD) system developed at UCLA by CJ Kim, a grid ....etc

[:=Read Full Message Here=:]

PROJECT GUIDE :
Dr.K.RAMANATHAN

Presented by:
K.KARTHIKEYAN




Abstract

Titanium nitride (TiN) is an extremely hard ceramic material, often used as a coating on titanium alloys, steel, carbide, and aluminium components to improve the substrate's surface properties.


Applied as a thin coating, TiN is used to harden and protect cutting and sliding surfaces, for decorative purposes (due to its gold appearance), and as a non-toxic exterior for medical implants.

TiN coating is for edge retention and corrosion ....etc

[:=Read Full Message Here=:]

This article is presented by:
Suryanarayana K.Y
Sharik Khan
Vinyas Rai M.V
Amit J Rao
Visvesvaraya Technological University
BELGAUM - 590 018


DESIGN AND FABRICATION OF PLASTIC COATING MACHINE

Introduction

Plastic products play a very important role in the modern world. The uses of plastic coated products are increasing day by day. Polyethylene, polystyrene, poly vinyl chloride are largely used in the manufac ....etc

[:=Read Full Message Here=:]

Presented By:
MD.IMTYAZ AHMED


NANO ENABLED COATING MAKES AIRCRAFT INVISIBLE
2.0 RADARS
 The first to use radio waves to detect the presence of distant metallic objects”
 first established principles regarding frequency and power level for the first primitive radar units
 RAPID capable of detecting an aircraft within 3 km of a receiver.
 The British were the first to fully exploit radar as a defense against aircraft attack.
 the US Army and US Navy were working on radars with the same p ....etc

[:=Read Full Message Here=:]

i want the project repot with word format and power point format....with detailed diagrams and report ....etc

[:=Read Full Message Here=:]

ABSTRACT

The concept of insulating cooled heat engine components such as gas turbine blades and diesel engine valves from hot working fluids with a ceramic thermal barrier coating is by no means new. A practical system, however, has only been identified in the past few years. Thermal barrier coating (TBC) are applied to metallic components to reduce metal temperature, reduce life cycle cost, increase the environmental resistance and in some cases reduce noxious exhaust emissions. The selection of TBC involves many consider ....etc

[:=Read Full Message Here=:]

ANALYSIS OF CATALYTIC COATING IN THE COMBUSTION CHAMBER IN FOUR STROKE ENGINES

ABSTRACT:


The analysis of catalytic coating in the combustion chamber in four

stroke engine is done in order to improve the performance of the vehicle and also to

reduce the percentage of harmful pollutants in the exhaust gas. In four stroke engines,

the combustion chamber is modified by applying catalytic coating means of

electroplating. Catalytic materials are used in order to provide minimize the pollutant
....etc

[:=Read Full Message Here=:]

I'm a final working on pedal powered n I would like to b help with the methodology of the project ....etc

[:=Read Full Message Here=:]