i need ppt on the topic case studies and government regulation for controlling cyber crime.... as soon as possible :)
....etc

[:=Read Full Message Here=:]

Objectives:

Help students to discover what makes the “Percentages” important in almost all the tests.

Help students to learn how to deal with different real-time applications of percentages.

Help students to understand how to go about the study material and what to do before coming to
the next lecture.

Help students to make use of LOGIC in place of conventional methods.
Step 1: Fundamentals - 1
1. Change of base
2. Successive percentage change
Step 2: Fundamentals - 2
3. Simple and compound Interest
4. Inter ....etc

[:=Read Full Message Here=:]

WASHOUT CONTROL FOR MANUAL OPERATIONS

SEMINAR REPORT
Submitted by

NEVIN AUGUSTINE
Seventh Semester
B.Tech,
Applied Electronics & Instrumentation
DEPARTMENT OF ELECTRONICS AND COMMUNICATION ENGINEERING
COLLEGE OF ENGINEERING
TRIVANDRUM

2010



ABSTRACT

It is known that limitations of human accuracy in manual manipulation hinder the quality of work performed by human operators of manual control systems. Indeed, movements of operators are apt t ....etc

[:=Read Full Message Here=:]

The programmer devices requiredfor programming theelectrically programmable readonlymemories (EPROMs) are generallyexpensive. Here is a low-cost circuit toprogram binary data into 2716 and Priyank Mudgal 2732 EPROMs.The circuit uses timer NE555 (IC2)wired as a monostable. When push-toonswitch S1 is pressed, IC2 generatesa 50ms pulse, which is given to the programpin 18 of the ZIF SOCKET throughswitch S2. EPROM is inserted into theZIF SOCKET for programming. LED1 to indicate the application of theprogramming pulse to the EPROM.B ....etc

[:=Read Full Message Here=:]

Please give me study material for mechanical project 'manual weight lifting machine' ....etc

[:=Read Full Message Here=:]

give me compounding and regulation notes ....etc

[:=Read Full Message Here=:]

NI-488.2 Software Reference Manual for MS-DOS


Introduction

This chapter introduces you to the General Purpose Interface Bus (GPIB)
and this manual. The National Instruments family of GPIB products for
your personal computer will become a valued and integral part of your work environment.

Introduction to the GPIB

The GPIB is a link, or interface system, through which interconnected
electronic devices communicate.

History of the GPIB[/b ....etc

[:=Read Full Message Here=:]

PC BASED MANUAL GUIDED VEHICLE USING RF WIRELESS TECHNOLOGY
The main aim of this project is to design a system that behaves like a robot and control it using RF technology. Robot is a system that contains sensors, control systems, manipulators, power supplies and software all working together to perform a task. Designing, building, programming and testing a robot is a combination of physics, mechanical engineering, electrical engineering, structural engineering, mathematics and computing.
This project describes a ne ....etc

[:=Read Full Message Here=:]

Manual gearbox 02T

Design and Function
With the new 02T 5/6-speed manual gearbox of the MQ200 series, Volkswagen has succeeded in developing an ultra-light twin-shaft gearbox. The housing is manufactured from magnesium. The gearbox can transmit up to 200 Nm of torque and is used throughout the Group in combination with various engines ranging from the A00 class to the A class. The final drive ratios and the ratios of the individual gears can be matched to the power outputs of the various engines. The type divers ....etc

[:=Read Full Message Here=:]

PART A
Simulation Exercises
Aim: To observe the effect of congestion by setting the parameters like, varying the queue size and page link bandwidth.
1. Simulate a three-node point-to-point network with a duplex page link between them. Set the queue size and vary the bandwidth and find the number of packets dropped.
Topology:-
Commands Used at Sender node and Receiver Node:
Sender:-
stcp –p 2000 –l 1024 1.0.1.2
Receiver:-
rtcp –p 2000 –l 1024
Results:
Case 1: set bandwidth to 10 Mbps and Queue size as 50
....etc

[:=Read Full Message Here=:]