Can u give me ideas abt VOICE RECOGNITION BASED WHEEL CHAIR CONTROL SYSTEM FOR PHYSICALLY CHALLENGED PEOPLE


Reference: http://studentbank.in/report-bio-medical-engineering-project-ideas#ixzz1Q7VytLfA

plz gv me a blue print of project and plz also send me a abstract of this ....etc

[:=Read Full Message Here=:]

how does the robot works and what r the essential components for this. ....etc

[:=Read Full Message Here=:]

Abstract:
This Project Line Following Autonomous Robot is based on 8 bit Microcontroller. This Robot follows the black line which is drawn over the white surface or it follows the white line which is drawn over the black surface. The infrared sensors are used to sense the line. When the infrared signal falls on the white surface, it gets reflected and if it falls on the black surface, it is not reflected this principle is used to scan the Lines for the Robot. All the above systems are controlled by the Microcontroller. Microcontroller g ....etc

[:=Read Full Message Here=:]

Light Following Robot,
By : Chiu Yun Fang
First off, if your new to BEAM and haven't had much experience with electronics, go to Solarbotics and buy the Photopopper 4.2 kit. It is an excellent kit with all the parts you'll need, a high output solarcell, new pager motors, omni-directional feeler switches, in-depth and informative documentation and a cute little PCB. It's well worth the money! Here's a couple pics to wet your appetite


The BEAM photovore is an autonomous robot that is entirely powered by solar ener ....etc

[:=Read Full Message Here=:]

Most wheeled mobile robot (WMR) controllers have been developed based on nonskidding and nonslipping assumptions. Unfortunately, wheel skidding and slipping are inevitable due to wheel tire-deformation; consequently, the stability and performance of these controllers are not guaranteed. This brief aims to develop a global positioning system (GPS)-based path following a controller for a car-like wheeled mobile robot in the presence of wheel skidding and slipping. The proposed control scheme uses real-time kinematic (RTK)-GPS and other aiding sen ....etc

[:=Read Full Message Here=:]

Practical Line Following Robot Documentation

1 Introduction
1.1 Preface
This practical has been established to provide the microcontroller course at the
Vienna University of Technology with an autonomous robot. The robot should be
programmed by students participating in this course. The goal of this practical is
to develop a working prototype suitable for teaching purposes.
Line following is the ability of an autonomous robot to follow a line marked along
the floor. This primary objective should be accomplished i ....etc

[:=Read Full Message Here=:]

am using p89v5rd2 microcontroller for my line follower robot project.
please tell me about the pin and circuit diagram for this one. ....etc

[:=Read Full Message Here=:]

Linbot advanced line following robot
by : activerobot
Linbot is an advanced line tracer robot. It has one pair of infrared emitters and sensors directed forward, as well as three pairs of infrared emitters and sensors directed downward. Linbot can follow a black line placed on a white floor as well as a white line on a black floor.

When it meets with an obstacle while following the line, it makes a U-turn and continues on. It comes in kit form, allowing the user to acquire hands on experience in robo ....etc

[:=Read Full Message Here=:]

LINE FOLLOWING ROBOT

Introduction

What is a line follower?
Line follower is a machine that can follow a path. The path can be visible like a black line on a white surface (or vice-versa) or it can be invisible like a magnetic field.
Why build a line follower?
Sensing a line and maneuvering the robot to stay on course, while constantly correcting wrong moves using feedback mechanism forms a simple yet effective closed loop system. As a programmer you get an opportunity to Ëœteachâ„¢ the rob ....etc

[:=Read Full Message Here=:]

whats the power supply to be given for the project ??i have used 12v geared motor and building it on a 3mm hard board...i am doing it using the one in the attachment i have given...
please do tell me the power supply and where the second ckt must be connected please do tell me...




....etc

[:=Read Full Message Here=:]