i want coordinated master control project i.e.,boiler follow mode and turbine follow mode
i have doubt this project o help me ..........................
....etc

[:=Read Full Message Here=:]

Abstract”
A major disadvantage of applying sliding mode control to dc/dc converters is that the steady-state switching frequency is affected by line and load variations. This is undesirable as it complicates the design of the input and output filters. To reduce switching frequency deviation in the events of line and load variations, an adaptive feedforward control scheme that varies the hysteresis band according to the change of line input voltage and an adaptive feedback control scheme that varies the control parameter (i.e., sliding c ....etc

[:=Read Full Message Here=:]

hai,
i need i-mode technology seminar report and ppt please help me. ....etc

[:=Read Full Message Here=:]

i-Mode: A Robust Model For Mobile Internet of The Future



NTT DoCoMo's i-mode is a mobile internet (as opposed to wireless internet) service popular in Japan. Unlike Wireless Application Protocol or WAP, i-mode encompasses a wider variety of internet standards, including web access, e-mail and the packet-switched network that delivers the data. i-mode users have access to various services such as e-mail, sports results, weather forecast, games, financial services and ticket booking. ....etc

[:=Read Full Message Here=:]

Stable tearing crack growth (slow ductile growth of a macroscopic crack in a load-bearing structure) is an important fracture failure process in ductile materials (e.g. metals) and usually precedes the final catastrophic failure of a structure. In recent years, there has been a growing demand for a simulation-based structural design and evaluation methodology that takes into account the stable tearing crack growth process. Within such a methodology, two tools must be available: (1) an efficient computer simulation code that can handle the kinem ....etc

[:=Read Full Message Here=:]

Ductile Mixed-mode Fracture Criterion Development and Crack Growth Simulations




Stable tearing crack growth (slow ductile growth of a macroscopic crack in a load-bearing structure) is an important fracture failure process in ductile materials (e.g. metals) and usually precedes the final catastrophic failure of a structure. In recent years, there has been a growing demand for a simulation-based structural design and evaluation methodology that takes into account the stable tearing crack growth process. Within such a methodology, two too ....etc

[:=Read Full Message Here=:]

Failure mode and effects analysis (FMEA)

Failure mode and effects analysis (FMEA) is a method (first developed for systems engineering) that examines potential failures in products or processes. It may be used to evaluate risk management priorities for mitigating known threat-vulnerabilities.

FMEA helps select remedial actions that reduce cumulative impacts of life-cycle consequences (risks) from a systems failure (fault).

By adapting hazard tree analysis to facilitate visual learning, this m ....etc

[:=Read Full Message Here=:]

Am rema,want to know about an efficient common mode hybrid filter used in SMPS for my seminar work.


Abstract obtained from IEEE is After the study of electromagnetic interference (EMI)
mechanisms in switching mode power system (SMPS) and the soft
switch, this paper proposes a novel hybrid filter (HEF) to suppress
commend mode EMI in SMPS. The HEF consists of a passive filter
and an active filter. Matching network, which can reduce
impedance mismatching effects, is introduced in passive part. A
....etc

[:=Read Full Message Here=:]

difference between internet and x-internet?? ....etc

[:=Read Full Message Here=:]

EFFECTS OF KEY FACTORS ON THE ENGINE COMBUSTION MODE SWITCHING BETWEEN HCCI AND SI
INTRODUCTION
 HCCI IS A PROMISING ENGINE COMBUSTION CONCEPT
 ADVANTAGES OF HIGH FUEL ECONOMY AND ULTRA LOW NOx EMISSIONS
 LIMITED APPLICATION-DIFFICULTY IN CONTROLLING AUTO-IGNITION
 SOLUTION:A HYBRID COMBUSTION SYSTEM IN GASOLINE DIRECT INJECTION ENGINES
HYBRID COMBUSTION SYSTEM
 COMBINATION OF SI AND HCCI MODE IN DIFFERENT OPERATING REGIONS
 HCCI MODE IN MIDDLE/LOW LOADS
 SI MODE IN HIGH SPEED/ ....etc

[:=Read Full Message Here=:]