Development of the Carbon Fiber Reinforced Carbon-carbon Composite for High Temperature Gas-cooled Reactors
In the present paper. details of the development of the candidate CIC composite are described. In the material development, especially, feasibility of the production. stableness of the supply and cost are much taken into consideration. As the physical properties of the material, high mechanical strength such as tensile and bending, high fracture strain and fracture toughness and low dimensional change by neutron ....etc

[:=Read Full Message Here=:]

ABSTRACT
This report present a novel idea to capture and represent compressible signals for transmission and storage at a rate below the Nyquist rate. This method is known as compressive sampling/sensing employs non adaptive linear projections that preserve the structure of the signal. The signal is reconstruced from these projections using optimization techniques.




TABLE OF CONTENTS
1 Introduction 1
2 Data Compression 3
2.1 Types of Data Compression . . . . . . . . . . . . . . . . . . . . . . 5
2.1.1 Loss ....etc

[:=Read Full Message Here=:]

1) INTRODUCTION
1.1 Basics of Bond Strength
a) Bond:-Bond in reinforcement refers to the adhesion between the reinforcing steel and the surrounding concrete.
b) Importance of Bond b/w steel and concrete:-The bond between the reinforcing steel and the surrounding concrete is responsible for the transfer of axial force from a reinforcing bar to surrounding concrete, thereby providing strain compatibility and composite action of concrete and steel. If this bond is in adequate, slipping of the reinforcing bar will occu ....etc

[:=Read Full Message Here=:]

My name harpreet singh from patiala ,Punjab
I have equipment to check the compression of mild steel . please send me a experiment repot of compressive strength of mildsteel.
compressive strength of mild steel whole experiment with observation? ....etc

[:=Read Full Message Here=:]

ABSTRACT

This test method covers determination of the compressive strength of hydraulic cement mortars, using 2-in. or cube specimens.Test Method C 349 provides an alternative procedure for this determination (not to be used for acceptance tests). This test method covers the application of the test using either inch-pound or SI units. The values stated in either system shall be regarded separately as standard. Within the text, the SI units are shown in brackets. ....etc

[:=Read Full Message Here=:]

Strength based and Displacement Based Design method for steel


Abstract

The performance based seismic design of Steel moment resisting frame structures aimed at controlling the structural damage based on precise estimations of proper response parameters. The primary focus of this study is on the development of a detailed assessment of the inelastic seismic behavior, response, and performance of typical ductile Steel moment resisting frame structures. This research tries to assess the Strength based and Disp ....etc

[:=Read Full Message Here=:]

The concepts of Wireless Sensor Networks and its issues like, energy efficiency, reduce communication bandwidth for maximize battery life, dynamically changed topology, WSN need a low rate inter sensor communication is required so required compression –estimation sensor. Classified as two Fusion Center(FC) and Adhoc WSNs. Another paper relating to this area :
• Jia Mengl , Husheng Li2 , and Zhu Hanl, Sparse Event Detection in Wireless Sensor Networks using Compressive Sensing, on information theory , may 2009.
describes a a circuit ....etc

[:=Read Full Message Here=:]

i have need some ppt's of compressive strength of cement. ....etc

[:=Read Full Message Here=:]

Gary Morphy
VARI-FORM

ABSTRACT
The need for lighter, stronger, more rigid vehicle structures will increasingly require complex hydroformed structural tubes to increase strength, and decrease weight, cost and part count. This effort will increase the use of high strength, low alloy (HSLA) steel, in place of SAE 1006/1008 or 1010 steel. Traditional hydroforming techniques require the higher elongation of the latter materials. An alternative tube hydroforming process has been d ....etc

[:=Read Full Message Here=:]

BY: P.D.NITYA




Need For Low Energy- Intensive Methods For Treating Low Strength - Large Volume Wastewater (like sewage, industrial washwater, etc.)


1.1 Definition of Low Strength Wastewater

Typical composition of untreated domestic wastewater (influent) was defined using concentration levels as weak, medium, and strong. Weak, medium, and strong levels of BOD5 (mg/L) were identified as 110, 220, and 400, concentrations of TSS (mg/L) were identified as 100, 220, and 350, and concentrations of ....etc

[:=Read Full Message Here=:]