Under the Guidance of Dr. Patil Basavaraj VDept of IP & E
Submitted By Deepak Kothari

Introduction to CWR

The CWR is a rotary forming process, consists
of the forming of forging by means of wedge-shaped tools that are fixed on the mill rolls with the same rotary direction.
In CWR process, there are five stages in the work piece deformation process corresponding to five zones of the wedged tool geometry, i.e., knifing, guiding, stretching, shaping, and siz ....etc

[:=Read Full Message Here=:]

I begin to use the comsol bofore two days, and I need some help for using comsol to simulate the solar cell,such as how to set the model of solar cell ,and so on ....etc

[:=Read Full Message Here=:]

Submitted By
Vinit Tarey


ABSTRACT
Many system-on-chip (SoC) integrated circuits contain embedded cores with different scan frequencies. To better meet the test requirements for such heterogeneous SoCs, leading tester companies have recently introduced port-scalable testers, and Many IP core design software like Xilinx, Leonardo Spectrum, and Modelsim etc which can used to design ip core like DMA ,Interrupt Controller etc .These Ip core can be Power aware an Implement on soc by choosing different design tech ....etc

[:=Read Full Message Here=:]

Integrating Structural Design and Formal Methods in RealTime System Design

Formal methods have been advocated as one of those techniques that can produce highquality software and hardware systems that has been demonstrated to come in ontime, within budget, and satisfy procurer requirements. They are, however, perceived to be difficult to use and unsuitable for presentation to nonspecialists. In addition, they have been criticized for paying too little attention to the system development process.
....etc

[:=Read Full Message Here=:]

Formal methods have been advocated as one of those techniques that can produce highquality software and hardware systems that has been demonstrated to come in ontime, within budget, and satisfy procurer requirements. They are, however, perceived to be difficult to use and unsuitable for presentation to nonspecialists. In addition, they have been criticized for paying too little attention to the system development process.

Traditional structured (bubblesandarrows) methods, however, do excel at supporting the development process, but do not ....etc

[:=Read Full Message Here=:]

how to use the chart SELECTION OF MODULE & FACE WIDTH CHART OF SPUR GEAR
in gear design ....etc

[:=Read Full Message Here=:]

DEPARTMENT OF ELECTRONICS & COMMUNICATION ENGG.

KURUKSHETRA INSTITUTE OF TECHNOLOGY & MANAGEMENT
KURUKSHETRA- 136119



Microelectromechanical systems
Microelectromechanical systems (MEMS) (also written as micro-electro-mechanical, MicroElectroMechanical or microelectronic and microelectromechanical systems) is the technology of very small mechanical devices driven by electricity; it merges at the nano-scale into nanoelectromechanical systems (NEMS) and nanote ....etc

[:=Read Full Message Here=:]

Common Emitter BJT Amplifier Design Current Mirror Design


Some Random Observations
● Conditions for stabilized voltage source biasing
● Emitter resistance, RE, is needed.
● Base voltage source will have finite resistance, RB.
● needs to be much larger than RB.
● Small RB - relative to RS - will attenuate input signal.
● Larger RE permits larger RB, but results in lower gain.
● Gain = -RC/RE for RE >> re.
● Split RE with bypassing increa ....etc

[:=Read Full Message Here=:]

blockdiagram of electronic voting machine..
and implementation

block diagram and implementation of electronic voting machine ....etc

[:=Read Full Message Here=:]

This article is presented by:
Sapana Mehta


Design Patterns


A pattern is a proven solution to a problem in a context.
Christopher Alexander says each pattern is a three-part rule which expresses a relation between a certain context, a problem, and a solution.
Design patterns represent a solutions to problems that arise when developing software within a particular context.
i.e Patterns = problems.solution pairs in a context

Background

Started in 1987 by Ward Cunningham and Ken Beck who were workin ....etc

[:=Read Full Message Here=:]