HYDRAULIC ROOF SUPPORT

A PROJECT REPORT ON
“HYDRAULIC ROOF SUPPORT”
SUBMITTED BY
Sachin D. Kongle Mithun A. Gore
Pramod B.Wadhai Arjun S. Maher
Rushikesh P. Patil Sarang B. Mahajan
(student’s of Third year Mechanical engineering)
GUIDED BY
Prof. G. R. Bhad
(Lect. In Mechanical Engg. Dept.)
DEPARTMENT OF MECHANICAL ENGINEERING,


INTRODUCTION

Roof support is a major problem affecting safety and productivity in underground mines.
Introduction of mechanization also cal ....etc

[:=Read Full Message Here=:]

Roof cooling techniques : a design handbook
.
ABSTRACT:

Natural heating and cooling of buildings helps to improve energy efficiency in the built environment. This book considers the principles of roof design and specific systems and cooling techniques.
Environmental function is considered in terms of protective strategies (solar control, thermal insulation, heat storage and thermal inertia) and selective strategies (radiative, evaporative and convective cooling and planting of roofs). Traditio ....etc

[:=Read Full Message Here=:]

i was working on a project with multi pitch roof so i was trying to find out similar design and analysis examples worked before, so please let me have it in pdf format ....etc

[:=Read Full Message Here=:]

Integrating Structural Design and Formal Methods in RealTime System Design

Formal methods have been advocated as one of those techniques that can produce highquality software and hardware systems that has been demonstrated to come in ontime, within budget, and satisfy procurer requirements. They are, however, perceived to be difficult to use and unsuitable for presentation to nonspecialists. In addition, they have been criticized for paying too little attention to the system development process.
....etc

[:=Read Full Message Here=:]

I wanted ppt& report Plz send me as soon as possible...... ....etc

[:=Read Full Message Here=:]

Submitted By
Vinit Tarey


ABSTRACT
Many system-on-chip (SoC) integrated circuits contain embedded cores with different scan frequencies. To better meet the test requirements for such heterogeneous SoCs, leading tester companies have recently introduced port-scalable testers, and Many IP core design software like Xilinx, Leonardo Spectrum, and Modelsim etc which can used to design ip core like DMA ,Interrupt Controller etc .These Ip core can be Power aware an Implement on soc by choosing different design tech ....etc

[:=Read Full Message Here=:]

Formal methods have been advocated as one of those techniques that can produce highquality software and hardware systems that has been demonstrated to come in ontime, within budget, and satisfy procurer requirements. They are, however, perceived to be difficult to use and unsuitable for presentation to nonspecialists. In addition, they have been criticized for paying too little attention to the system development process.

Traditional structured (bubblesandarrows) methods, however, do excel at supporting the development process, but do not ....etc

[:=Read Full Message Here=:]

Common Emitter BJT Amplifier Design Current Mirror Design


Some Random Observations
● Conditions for stabilized voltage source biasing
● Emitter resistance, RE, is needed.
● Base voltage source will have finite resistance, RB.
● needs to be much larger than RB.
● Small RB - relative to RS - will attenuate input signal.
● Larger RE permits larger RB, but results in lower gain.
● Gain = -RC/RE for RE >> re.
● Split RE with bypassing increa ....etc

[:=Read Full Message Here=:]

hi
i would like to know the reinforcement details of rcc folded plates roofing structure ....etc

[:=Read Full Message Here=:]

This article is presented by:
Sapana Mehta


Design Patterns


A pattern is a proven solution to a problem in a context.
Christopher Alexander says each pattern is a three-part rule which expresses a relation between a certain context, a problem, and a solution.
Design patterns represent a solutions to problems that arise when developing software within a particular context.
i.e Patterns = problems.solution pairs in a context

Background

Started in 1987 by Ward Cunningham and Ken Beck who were workin ....etc

[:=Read Full Message Here=:]