PROJECT GUIDE :
Dr.K.RAMANATHAN

Presented by:
K.KARTHIKEYAN




Abstract

Titanium nitride (TiN) is an extremely hard ceramic material, often used as a coating on titanium alloys, steel, carbide, and aluminium components to improve the substrate's surface properties.


Applied as a thin coating, TiN is used to harden and protect cutting and sliding surfaces, for decorative purposes (due to its gold appearance), and as a non-toxic exterior for medical implants.

TiN coating is for edge retention and corrosion ....etc

[:=Read Full Message Here=:]

SCATTERING PARAMETERS OF CIRCULATOR

SCATTERING PARAMETERS OF CIRCULATOR


AIM: To study the operation of ferrite circulator and hence measure
i. Insertion loss ii. Isolation iii. And to determining S parameters

EQUIPMENT: Microwave Source (RKO/GO), Isolator, Variable Attenuator, Frequency meter, Slotted line , Tunable probe with detector, detector mount with detector, VSWR meter, Circulator and Matched Terminations-2.

THEORY: The circulator is a multi port junction that permits transmission ....etc

[:=Read Full Message Here=:]

Abrasive Jet Machine

Introduction
Abrasive jet machining (AJM) is a non-traditional machining
process that can machine material without generating heat and
shock.
Abrasive jet machining (AJM) is commonly used for Cutting,
Cleaning, Drilling and Etching operation

Mechanism of AJM

Fine particles are accelerated in
gas stream .


The particles are directed towards
the focus of machining.

As the particle impacts the surface,
....etc

[:=Read Full Message Here=:]

Hello.
i need the step by step guideline for constructing the microwave isolator in HFSS software asap.
thanks ....etc

[:=Read Full Message Here=:]

BY:Kyaw Swar Win, Soe Win, Aung May Than



ABSTRACT

Field experiments were conducted in pre-monsoon and monsoon seasons, 2008 at Food Legumes Section, Department of Agricultural Research (DAR) to select the suitable lines for pre-monsoon and monsoon seasons, to estimate the genetic variability, heritability and genetic advance for yield and agronomic characters among the tested mungbean breeding lines and to study the association of yield and agronomic ch ....etc

[:=Read Full Message Here=:]

At present any consignment carried by a vehicle has to travel incommunicado till it reaches the destination. So, both the fleet owner and the persons sending or procuring the consignment have to sit keeping their fingers crossed till the fleet arrives. To track the path of the vehicle and to monitor the various parameters like fuel consumption, kilometers covered and the amount of load in the vehicle an intelligent device would come handy to solve the problem for the fleet operators and the clients. This paper aims at designing an intelligent d ....etc

[:=Read Full Message Here=:]

PERFORMANCE EVALUATION OF OPERATIONAL PARAMETERS ON RFID CONTROLLED CONVEYOR SYSTEM.

ABSTRACT: RFID has been taking great attention of industry for its various advantages. This technology enables to monitor and track items in production facilities, warehouse operations, and distributions. However, RFID system performance is dramatically affected from the operational setting of the system. In particular, identification of appropriate levels for each operational factor is not trivial. In this project, we demonstrate an effective methodology to ....etc

[:=Read Full Message Here=:]

Do you have an HFSS (V 13) tutorial on designing a coax ferrite circulator? ....etc

[:=Read Full Message Here=:]

EFFECT OF DIMENSIONAL PARAMETERS ON THE PERFORMANCE OF VORTEX TUBE


INTRODUCTION

Vortex tube is a simple device, which can cause energy separation. The principle of vortex tube is vortices produced by tangential velocity as a main driving force for the energy separation in the vortex tube.
It consists of nozzle, vortex chamber, separating cold plate, hot valve, and hot and cold end without any moving parts. In the vortex tube, when works, the compressed air expands in the nozzle ....etc

[:=Read Full Message Here=:]

ABSTRACT

This paper describes in detail, field experiments performed on a single-phase, distribution transformer to study the behavior of transformer terminal parameters during internal winding faults. A custom-built transformer provided with external taps was used for these tests. The taps were used to stage various internal winding faults in the transformer. Terminal values of voltages and currents were monitored and the results presented. A comparison of these results with simulation results is also presented


Presented By:
Palm ....etc

[:=Read Full Message Here=:]