A STUDY ON CUSTOMER SATISFACTION FOR BSNL PRODUCTS AND SERVICES AND ITS ROLE IN BUILDING BRAND EQUITY FOR THE COMPANY.
Project Report submitted by
SARAVANA PERUMAL.G
Register No: 010771037
Batch: 2005-07

SYNOPSIS
The Telecom industry is one of the leading and fastest growing in the world as communication plays a vital role in the world and especially in India. It acts as a major catalyst for the economic growth.
BSNL has good brand awareness among the people. This could be attributed to its long history in the market ....etc

[:=Read Full Message Here=:]

Electrical Characteristics of n-ZnO/p-Si Heterojunction Diodes
4
Grown by Pulsed Laser Deposition at Different Oxygen
5
Pressures
6
7
R.S. AJIMSHA,
1
M.K. JAYARAJ,
1,3
and L.M. KUKREJA
2
8
1.”Optoelectronics Devices Laboratory, Department of Physics, Cochin University of Science and
9
Technology, Kochi 682022, India. 2.”Laser Materials Processing Division, Raja Ramanna Centre
10
for Advanced Technology, Indore 452013, India. 3.”e-mail: [email protected]
11
Heterojunction diodes of n-type ZnO/p-type silicon (1 ....etc

[:=Read Full Message Here=:]

i looking this paper every week karmasangsthan e paper
....etc

[:=Read Full Message Here=:]

what is fdi in hindi ....etc

[:=Read Full Message Here=:]

The file system must be user friendly as far as possible. Hence the operation on the system by tfie costumers must be limited. Thus the procedure for a search can be settled as follows. 'First of all the system displays a message Search:- to the costumer. The costumer must enter the first few letters of the name of the tram or the product or the patient. Then he must close the enter hey. Then the soft key 'FT' can be keyed to start the search. The system displays the details of if any match occurs. The Tsc %ey can 6 ....etc

[:=Read Full Message Here=:]

Electrical Characteristics of n-ZnO/p-Si Heterojunction Diodes
4
Grown by Pulsed Laser Deposition at Different Oxygen
5
Pressures
6
7
R.S. AJIMSHA,
1
M.K. JAYARAJ,
1,3
and L.M. KUKREJA
2
8
1.”Optoelectronics Devices Laboratory, Department of Physics, Cochin University of Science and
9
Technology, Kochi 682022, India. 2.”Laser Materials Processing Division, Raja Ramanna Centre
10
for Advanced Technology, Indore 452013, India. 3.”e-mail: [email protected]
11
Heterojunction diodes of n-type ZnO/p-type silicon (1 ....etc

[:=Read Full Message Here=:]

INTRODUCTION
Rapid prototyping automates the fabrication of a prototype part from a three- dimensional (3D) CAD drawing. This physical model conveys more complete information about the product earlier in the development cycle. The turnaround time for a typical rapid prototype part can take a few days. Conventional prototyping may take weeks or even months, depending on the method used. Rapid prototyping can be quicker more cost effective means of building prototypes as opposed to conventional methods.
F ....etc

[:=Read Full Message Here=:]

DESIGN OF BOILER STACK
ABSTRACT
Chimney, which form the last component of a system using a flue gas such as feoiler, IC engines, play a vital role in maintaining efficiency, draft, etc, of a system and also in minimizing the atmospheric pollution.
The boiler plant of HOCL had used LSHS (low Sulphur heavy stock) as a fuel. Recently they changed the fuel to LSFO (low Sulphur furnace oil). As a combined effect of increased corrosion rate and natural calamities the stack had undergone failure. As per the Kerala State Polluti ....etc

[:=Read Full Message Here=:]

COST EFFECTIVENESS OF MINERAL WOOL INSULATION Vs PERLITE INSULATION
PROJECT REPORT
Submitted by
DIPU.K.SHAJI GITHU BABU VARUN KUMAR. T.K VIMAL MENON
ABSTRACT
The main objective of this project is to make the cost effectiveness analysis of the system of the thermal insulation of the pipe lines in petrochemical plant which carries steam. In a chemical plant maintaining temperature of fluids in different pipe lines assume greatest importance as each process is performed at particular temperature.
The project work was car ....etc

[:=Read Full Message Here=:]

hi boss
i wanted a report and ppt on abrasive jet machining
plz can u help me........ ....etc

[:=Read Full Message Here=:]