|
| Thread / Post | Tags |
Title: fabrication of rotary kaller
Page Link: fabrication of rotary kaller -
Posted By:
Created at: Friday 24th of May 2013 11:58:01 AM
| fabrication of rotary k,
favrication of rotory killr,
fabrication rotry kaller,
what is rotary kaller,
rotary kaller block diagram,
rotary kaller,
fabrication of rotary kalle,
|
we are doing project on fabrication of rotary kaller so we need some information about that topic
....etc
[:=Read Full Message Here=:]
|
|
|
Title: FOREMAN - SERVICE WORKSHOP - kerala psc previous question paper
Page Link: FOREMAN - SERVICE WORKSHOP - kerala psc previous question paper -
Posted By: amrutha735
Created at: Thursday 20th of April 2017 07:10:22 PM
| |
236/2015
Maximum : 100 marks
Time : 1 hour and 15 minutes
1. The most preferred process for casting gas turbine blades is
(A) die moulding
(B)shell moulding
(C ) investment moulding
(D)sand casting
2.By which one of the following methods gray cast iron is usually welded?
(A) TIG welding
(B)MIG welding
(C ) Gas welding
(D)Arc welding
3.Submerged arc welding takes place :
(A) Under water
(B)In a cloud of gas
(C ) Between work surfaces
(D)Under a blanket of granular flux
4.Silicon is added to electrod ....etc
[:=Read Full Message Here=:]
|
|
|
Title: TURNER - STATE WATER TRANSPORT-kerala psc previous question paper
Page Link: TURNER - STATE WATER TRANSPORT-kerala psc previous question paper -
Posted By: anusree
Created at: Tuesday 25th of April 2017 03:46:35 PM
| |
1.The vernier bevel protractor is able to read the angle to an accurancy of _____degrees. The vernier bevel protractor is able to read the angle to an accuracy of
(A)1°
_r
12
(C )1°/2
(B)1/2
(D)11°/2
2.------------method is used in mass production for producing a small length of taper where
accuracy is not the criserion.
(A)Form Tool(B) Tail Stock Offset
(C ) Swivelling Compound rest(D) None of these
3.In tailstock offset taper turning method, the amount of offset is found by the formula :
(A)
(C )
(.D-d) ....etc
[:=Read Full Message Here=:]
|
Title: ROTORY HIGH EFFIENCY HYBRID CYCLE ENGINE
Page Link: ROTORY HIGH EFFIENCY HYBRID CYCLE ENGINE -
Posted By: smart paper boy
Created at: Saturday 30th of July 2011 07:07:15 PM
| |
INRODUCTION
Cycles
Comparison
Need
Conclusion
In this work we presented a rotary engine design which is capable of implementing the High Efficiency Hybrid Cycle. It is expected that this engine will demonstrate superior volumetric efficiency, as well as fuel efficiency across a broad range of loads. The result is an engine which may offer up to 57% peak efficiency & above 50% sustain efficiency across typical driving loads. The engine is currently being prototyped, with a functioning compressor already wor..............etc
[:=Read Full Message Here=:]
|
Title: LINEAR MOTORS AND ITS USE IN MAGLEV TRAIN
Page Link: LINEAR MOTORS AND ITS USE IN MAGLEV TRAIN -
Posted By: seminar class
Created at: Saturday 23rd of April 2011 01:51:29 PM
| |
PRESENTED BY
ABHISHEK KUMAR
LINEAR MOTORS AND IT’S USE IN MAGLEV TRAIN
INTRODUCTION
A LINEAR MOTOR OR LINEAR INDUCTION MOTOR IS AN AC ELECTRIC MOTOR THAT HAS ITS STATOR UNROLLED SO THAT INSTEAD OF PRODUCING A TORQUE(ROTATION) IT PRODUCES A LINEAR FORCE ALONG ITS LENGTH.
HOW LINEAR MOTORS WORK
SPLIT A ROTORY MOTOR RADIALLY ALONG ITS AXIS OF ROTATION
FLATTEN IT OUT:
RESULT: A FLAT LINEAR MOTOR THAT PRODUCES A DIRECT LINEAR FORCE INSTEAD OF TORQUE.
ANALYSIS METHO ....etc
[:=Read Full Message Here=:]
|
|
|
|
|
Title: fabrication of rotary kaller
Page Link: fabrication of rotary kaller -
Posted By:
Created at: Friday 24th of May 2013 11:58:01 AM
| fabrication of rotary kaller,
fabrication of rotart kaller,
what is rotary kaller,
fabrication of rotary kaller project,
yhs ddc bd,
fabricatiom of rotatry koller,
favrication of rotory killr,
|
we are doing project on fabrication of rotary kaller so we need some information about that topic
....etc
[:=Read Full Message Here=:]
|
|
|
|
|