RESILIENT PACKET RING TECHNOLOGY
#1
Star 

INTRODUCTION!!!
Over the past few years, new promising protocols have emerged at the forefront of Metro networking. One among them is the Resilient Packet Ring (RPR). Today, as the standard slowly settle, it is finally reaching the stage beyond speculation, and into network deployment. Pundits and vendors have pinned exceptional hopes on this technology, particularly for effecting a long-awaited transformation of Metro Area Networking.
The Metro remains the last geographical section of the network still largely dependent on late 1980s and early 1990s technology (low to mid-capacity SONET rings), and is clearly in need of data-focused improvements. RPR technology, on their own, adds features to Metro Area Networks that are currently lacking.
A protocol is a set of rules that governs the communications between computers on a network. These rules include guidelines that regulate the following characteristics of a network: access method, allowed physical topologies, types of cabling, and speed of data transfer etc.
commonly used protocols are:
The most common protocols in use today include:
¢ Ethernet
¢ Token Ring
¢ FDDI
¢ ATM etc


METROPOLITAN AREA NETWORKS
Metropolitan Area Network (MAN) is a computer network usually spanning a campus or a city, which typically connect a few local area networks using high speed backbone technologies. There are three important features, which discriminate MANs from LANs or WANs:
1. A MAN typically covers an area of between 5 and 50 km range (between LANs and WANs)
2. The MAN, its communications links and equipment are generally owned by either a consortium of users or by a network service provider.
3. A MAN is frequently used to provide a shared connection to other networks using a page link to a WAN and to share regional resources.
An important trend in networking is the migration of packet-based technologies from Local Area Networks to Metropolitan Area Networks (MANs). The MAN protocols are mostly at the data page link level. Some legacy technologies presently used for for Metropolitan Area Networks (MANs) include :
¢ Asynchronous Transfer Mode (ATM)
¢ Synchronous Optical NETwork (SONET)
¢ Fiber Distributed Data Interface (FDDI)
¢ DQDB
¢ SMDS.
¢ Gigabit Ethernet MANs & 10 Gigabit Ethernet

Asynchronous Transfer Mode (ATM)
The ATM composes a protocol suite, which establishes a mechanism to carry all traffic on a stream of fixed packets called cells. A fixed-size packet can ensure that the switching and multiplexing function could be carried out quickly and easily. ATM is a connection-oriented technology. ATM offers multiservice focus - remedy for carrying data, voice and video.
2.2 Synchronous Optical NETwork (SONET)
SONET is a synchronous system and is controlled by a master clock. The sender and the receiver are connected to the common clock.
2.3 Fiber Distributed Data Interface (FDDI)
FDDI is a set of ANSI protocols for sending digital data over fiber optic cable. FDDI networks are token passing and dual-ring networks, and support data rates of up to 100 Mbps. FDDI uses dual-ring architecture with traffic on each ring flowing in opposite directions (called counter-rotating). FDDI specifies the physical and media-access portions of the OSI reference model.
2.4 Distributed Queue Dual Bus (DQDB)
DQDB is a Data-link layer communication protocol for Metropolitan Area Networks (MANs). DQDB is designed for data as well as voice and video transmission based on cell switching technology (similar to ATM). DQDB permits multiple systems to interconnect using two unidirectional logical buses.

2.5 Switched Multimegabit Data Service (SMDS)
SMDS is a broadband networking technology developed based on the DQDB MAN technology. SMDS can use fiber- or copper-based media; SMDS operates by accepting high-speed customer data in increments of up to 9,188 octets, and divides it into 53-octet cells for transmission through the service providerâ„¢s network, which are reassembled at the receiving end into the customer data.
2.6 10-Gigabit Ethernet
10-Gigabit Ethernet, built on the Ethernet technology, offers data speeds up to 10 billion bits per second. It is used to interconnect LANs, WANs, and MANs. It uses the Ethernet MAC protocol and its frame format and size. It only functions over optical fiber. So it does not need the carrier-sensing multiple-access with Collision Detection (CSMA/CD) protocol as it is used in other Ethernet standards.
Reply
#2
[attachment=3450]
ABSTRACT
Resilient packet ring or RPR is a new MAC layer technology being standardized in the IEEE 802.17 workgroup, optimized for robust and efficient packet networking over a fiber ring topology. Rapidly increasing volume of data traffic in Metropolitan Area Networks is challenging the capacity limits of existing transport infrastructures based on circuit oriented technologies like SONET and ATM. The emerging solution for metro data transport application is packet ring technology. RPR incorporates main features that have been exclusive to SONET such as efficient support for ring topology, fast recovery from fiber cuts and page link failures. Also, RPR can provide features of Ethernet like data efficiency, simplicity and cost advantages.


INTRODUCTION
An important trend in networking is the migration of packet-based technologies from local Area Networks to Metropolitan Area Networks. The rapidly increasing volume of data traffic in metro networks is challenging the capacity limits of existing transport infrastructures based on circuit-oriented technologies like SONET and ATM. Inefficiencies associated with carrying increasing quantities of data traffic over voice-optimized circuit-switched networks makes it difficult to provision new services, and increases the cost of building additional capacity beyond the limits of most carriers' capital expense budgets. Packet-based transport technology, a natural fit with the now ubiquitous IP protocol, is considered by many to be the only alternative for scaling metro networks to meet the demand.
The emerging solution for metro data transport applications is Packet Ring technology. It offers two key features that have heretofore been exclusive to SONET: efficient support for ring topology and fast recovery from fiber cuts and page link failures. At the same time, Packet Ring technology can provide data efficiency, simplicity, and cost advantages that are typical to Ethernet. Even though there is currently no standard for Packet Rings operating at Gigabit speeds and higher, many vendors are developing and introducing Packet Ring technologies to address this emerging market.
To be a viable contender for data transport in the MAN, Packet Ring technology should provide support for multi-Gigabit data speeds and integrate seamlessly with existing Ethernet and SONET networks. Packet Ring solutions should be available in various form factors and page link speeds, and at prices that are competitive with Ethernet. Finally, an industry standard that defines the page link layer for Packet Rings needs to be developed to achieve vendor interoperability and customer acceptance.
LIMITATIONS OF SONET AND ETHERNET
SONET
Most metro area fiber is in ring form. Ring topology is a natural match for SONET-based TDM networks that constitute the bulk of existing metro network infrastructure. However, there are well-known disadvantages to using SONET for transporting data traffic (or point-to-point SONET data solutions, like Packet over SONET [POS]). SONET was designed for point-to-point, circuit-switched applications (e.g. voice traffic), and most of limitations stem from these origins. Here are some of the disadvantages of using SONET Rings for data transport:
Figure 2: SONET Access and Fully Meshed Networks
SONET provisions point-to-point circuits between ring nodes. Each circuit is allocated a fixed amount of bandwidth that is wasted when not used. For the SONET network that is used for access in Figure 2 (left), each node on the ring is allocated only one quarter of the ring's total bandwidth (say, OC-3 each on an OC-12 ring). That fixed allocation puts a limit on the maximum burst traffic data transfer rate between endpoints. This is a disadvantage for data traffic, which is inherently bursty.
¢ Waste of Bandwidth for Meshing.
If the network design calls for a logical mesh, (right), the network designer must divide the OC-12 of ring bandwidth into 10 provisioned circuits. Provisioning the circuits necessary to create a logical mesh over a SONET Ring is not only difficult but also results in extremely inefficient use of ring bandwidth. As the amount of data traffic that stays within metro networks is increasing, a fully meshed network that is easy to deploy, maintain and upgrade is becoming an important requirement.
¢ Multicast Traffic.
On a SONET Ring, multicast traffic requires each source to allocate a separate circuit for each destination. A separate copy of the packet is sent to each destination. The result is multiple copies of multicast packets traveling around the ring, wasting bandwidth.
¢ Wasted Protection Bandwidth.
Typically, 50 percent of ring bandwidth is reserved for protection. While protection is obviously important, SONET does not achieve this goal in an efficient manner that gives the provider the choice of how much bandwidth to reserve for protection.
Ethernet
How about Ethernet over a ring? Ethernet does make efficient use of available bandwidth for data traffic, and does offer a far simpler and inexpensive solution for data traffic. However, because Ethernet is optimized for point-to-point or meshed topologies, it does not make the most of the ring topology.
Unlike SONET, Ethernet does not take advantage of a ring topology to implement a fast protection mechanism. Ethernet generally relies on the spanning tree protocol to eliminate all loops from a switched network. Even though spanning tree protocol can be utilized to achieve path redundancy, it recovers comparatively slowly from a fiber cut since the recovery mechanism requires the failure condition to be propagated serially to each upstream node. Link aggregation (802.1ad) can provide a page link level resiliency solution, but it is comparatively slow (~500ms vs. ~50ms) and not appropriate for providing path level protection. Ethernet is also not good at implementing global "fairness" policies for sharing ring bandwidth. Ethernet switches can provide link-level fairness, but this does not necessarily or easily translate into global fairness.
RPR OPERATION
RPR technology uses a dual counter rotating fiber ring topology. Both rings (inner and outer) are used to transport working traffic between nodes. By utilizing both fibers, instead of keeping a spare fiber for protection, RPR utilizes the total available ring bandwidth. These fibers or ringlets are also used to carry control (topology updates, protection and bandwidth control) messages. Control messages flow in the opposite direction of the traffic that they represent. RPR has the ability to differentiate between low and high priority packets In addition, RPR nodes also have a transit path, through which packets destined to downstream nodes on the ring flow.
RPR Terminology
With a transit buffer capable of holding multiple packets, RPR nodes have the ability to transmit high priority packets while temporarily holding other low priority packets in the transit buffer.
The RPR MAC
As a Layer-2 network protocol, the MAC layer contains much of the functionality for the RPR network. The RPR MAC is responsible for providing access to the fiber media. The RPR MAC can receive, transit, and transmit packets.
Receive Decision
Every station has a 48-bit MAC address. The MAC will receive any packets with a matching destination address. The MAC can receive both unicast and multicast packets. Multicast packets are copied to the host and allowed to continue through the transit path. Matching unicast packets are stripped from the ring and do not consume bandwidth on downstream spans. There are also control packets that are meant for the neighboring node; these packets do not need a destination or source address.
Transit Path
Nodes with a non matching address are allowed to continue circulating around the ring. Unlike point-to-point protocols such as Ethernet, RPR packets undergo minimal processing per hop on a ring. RPR packets are only inspected for a matching address and header errors.
Transmit And Bandwidth Control
The RPR MAC can transmit both high and low priority packets. The bandwidth algorithm controls whether a node is within its negotiated bandwidth allotment for low priority packets. High priority packets are not subjected to the bandwidth control algorithm.
Topology Discovery
RPR has a topology discovery mechanism that allows nodes on the ring to be inserted/removed without manual management intervention. After a node joins a ring, it will circulate a topology discovery message to learn the MAC addresses of the other stations. Nodes also send these messages periodically (1 to 10 seconds). Each node that receives a topology message appends its MAC address and passes it to its neighbor. Eventually, the packet returns to its source with a topology map (list of addresses) of the ring.
THE ADVANTAGES OF PACKET RING NETWORKING
As we've seen, neither SONET nor Ethernet is ideal for handling data traffic on a ring network. SONET does take advantage of the ring topology, but does not handle data traffic efficiently, wasting ring bandwidth. Ethernet, while a natural fit for data traffic, is in fact difficult to implement on a ring, and does not make the most of the ring's capabilities. Packet Ring protocols, on the other hand, promise the best of both worlds. Packet Ring protocols create a full, packet-based networking solution that avoids the provisioning complications and inflexibility of SONET and provides the ring protection and global fairness features missing from Ethernet. Here are the general and specific advantages of Packet Ring networking.
The basic advantage of a Packet Ring is that each node can assume that a packet sent on the ring will eventually reach its destination node regardless of which path around the ring has taken. Since the nodes "know" they are on a ring, only three basic packet-handling actions are needed: insertion (adding a packet into the ring), forwarding (sending the packet onward), and stripping (taking the packet off the ring). This reduces the amount of work individual nodes have to do to communicate with each other, especially as compared with mesh networking where each node has to make a forwarding decision about which exit port to use for each packet.
Resiliency
Packet Rings have a natural resiliency advantage. A ring that is built using switches needs to distribute failure information across an entire network to recover fully from a fiber cut. In the Ethernet case, this can be accomplished using a spanning tree protocol. On the other hand, a Packet Ring protocol can use a "ring wrap" at the nodes surrounding the cut (see Figure 5).
In this case, only nodes that are adjacent to the failure need to take any action. Wrapped traffic can reach the original destination by going around the ring in the opposite direction. Ring fail-over is often described as "self-healing" or "automatic recovery." In practice, ring-based transport systems have reliably achieved <50ms fail-over periods.
Bandwidth Fairness
Packet Rings also have an inherent advantage for implementing fairness algorithms to regulate bandwidth usage. Ring bandwidth is a shared resource, and is vulnerable to exploitation by individual users or nodes, in the network version of the "the tragedy of the commons." A fairness algorithm is a mechanism that gives every node on the ring a predetermined "fair" share of the ring bandwidth, ideally without the straitjacket of a provisioned circuit. A ring-level fairness algorithm can and should allocate ring bandwidth as one global resource. Bandwidth policies that can allow maximum ring bandwidth to be utilized between any two nodes when there is no congestion can be implemented without the inflexibility of a fixed circuit based system like SONET, but with greater effectiveness than point-to-point Ethernet. For example, a Packet Ring can simply control the rate of packet forwarding relative to packet sourcing. This is an easy method of preventing neighboring nodes from acting as "bandwidth hogs." SONET also implements point-to-point circuits that allocate and reserve a fixed amount of bandwidth for each connection, but lack of flexibility is the problem. Adding or subtracting bandwidth requires manual configuration of new circuits, and the reservation of such circuits wastes bandwidth.
Example 1: Global Fairness and the Tragedy of the Commons
mternet”( E) A B
Li, Packet Ring
Ethernet

5 c
D <<^^^^~ C
In Example 1, the chain of switches on the left, we can see that Node D is vulnerable to the bandwidth usage patterns of Nodes A, B, and C. Ethernet switches typically allocate output port bandwidth fairly among all input ports. If each node, for example, is trying to send 2Gbs traffic to the Internet between the hours of 8pm to 12pm, Node A will be able to send 1Gbs, Node B will be able to send 500Mbs and nodes C and D will only be able to send 250Mbs each. As the number of nodes in the chain grows, the unfairness of Ethernet switches to nodes further upstream becomes even more significant.
One solution is to implement link-level rate limits on each node. For example, the ingress traffic at each switch might be rate limited to 500Mbs. But link¬level rate limiting policies don't translate into a global fairness policy and create a provisioning and efficiency problem for best effort data traffic similar to SONET circuits. If at 4am no one else is using any bandwidth, traffic from D need not be
limited to 500Mbs.
On the Packet Ring on the right, it is much easier to implement a global fairness policy, because the Packet Ring implements fairness policies at the level of the entire ring, not individual links. The service provider can set rules that govern the rate at which packets are forwarded from upstream or downstream nodes in relation to packets sourced by the node. That way, if none of the ring bandwidth is being used, Node D is free to source as many packets as needed. On the other hand, if Nodes A-C are each using 100Mbs, a Packet Ring can then automatically limit the amount of packets D is allowed to put on the ring, by controlling the source/forward relationship.
Broadcast or Multicast Traffic
Packet Rings are a natural fit for broadcast and multicast traffic. As detailed above, for unicast traffic, nodes on a Packet Ring generally have the choice of stripping packets from the ring or forwarding them. However, for a multicast, the nodes can simply receive the packet and forward it, until the source node strips the packet. This makes it possible to multicast or broadcast a packet by sending only one copy around the ring.
In Example 2, Source Node S wants to broadcast a packet to destination Nodes D1-D4. Using a POS network, S must replicate the packet and send a separate copy to each provisioned circuit. On a Packet Ring, Source Node S simply sends a single packet onto the ring that is received in turn by each D Node, and forwarded. The Packet Ring, in this example, uses one quarter the bandwidth as the SONET Ring for the same multicast.
The Packet Ring standards now in development create only a new Media Access Control (MAC) addressing scheme designed for ring-based topologies. This has the advantage of leaving Layer 1 open. Hence, Packet Ring technologies will be compatible with Ethernet, SONET, and DWDM physical layer standards.
Figure 6: Packet Rings are Physical and Network Layer Independent
(IP, MPLS, Others)
802.17 Packet Ring
Optical Transmission^ ONE T, Ethernet, WDM or new)
This means that Packet Rings can operate over an existing SONET configuration, creating better data capabilities without the need to replace SONET equipment or abandon SONET for TDM voice traffic. Similarly, a DWDM configuration can make use of Packet Ring at Layer 2 for some or all wavelengths. Finally, where dark fiber is available, a Packet Ring can operate without the need to purchase expensive Layer 1 gear.
Packet Rings in Application
Packet Rings suit the needs of many types of service providers in the metro area. A Packet Ring is useful anywhere that data transport over a fiber ring is needed. Resiliency and bandwidth sharing are important, but the cost or provisioning complexity of SONET is undesirable.
Let's focus first on a metro access/aggregation solution that might be used by a Metro Service Provider (i.e., an ILEC, CLEC, or BLEC) or (in modified form) a Broadband cable/DSL carrier. These carriers are typically looking to provide data transport services, preferably without the SONET overhead. Packet Ring technology is a perfect fit for these needs.
Figure 7: A Packet Ring Metro Access & Aggregation Solution
In this solution, a single Packet Ring serves the needs of multiple buildings in a metro area, over dark fiber (only three buildings are pictured, but in practice a single ring will be capable of supporting dozens of nodes/buildings). This solution has several notable features:
1. The Packet Ring at the center of this solution will allow the service provider to sell true protected bandwidth to the end-users, with a promise of <50 ms fail-over on all services. Each access node provides bandwidth to be added/dropped as desired. Higher layer protocols such as IP or MPLS can be used for service creation, while the resilient transport serves to guarantee service levels.
2. The fairness algorithms built into the Packet Ring will prevent any single node of the ring from "starving" other nodes, or imposing excessive delays.
3. Small form-factor Packet Ring routers will mean node equipment that can easily fit into existing configured spaces, such as a building basement (Node B), or a vault (Node C and D). In general, a small form factor will also mean a less expensive Packet Ring solution.
4. The presented solution demonstrates a healthy integration of Ethernet and Packet Ring technologies. Ethernet is used here for access and uplink, either in 10/100 (Node B), Gigabit (Node C), or 10 Gigabit (Node A) forms. In addition, for customers reachable only by TDM technologies (Node D), Riverstone's integration of WAN and Packet Ring technologies in a single platform means access for customers in every environment.
STANDARDIZATION
Efforts are underway to create a Resilient Packet Ring (RPR) standard. The IEEE 802.17 RPR working group is developing a standard that will define a Resilient Packet Ring Access Protocol for use in Local, Metropolitan, and Wide Area Networks. The 802.17 working group has been approved and had its first meeting in January 16-17, 2001. An 802.17 plenary meeting was held March 12-16, 2001 with 166 attendees from 89 organizations. At the end of this meeting, 21 objectives and requirements for the 802.17 RPR standard was accepted; acceptance of technical issues requires a 75 percent vote in IEEE standards groups.
Some of the goals of the 802.17 working group are:
(1) Support for dual counter rotating ring topology;
(2) Full compatibility with IEEE's 802 architecture as well as 802.1D, 802.1Q and 802.1f;
(3) Protection mechanism with sub 50ms fail-over;
(4) Destination stripping of packets;
(5) Adoption of existing physical layer medium to avoid technical risk.
The 802.17 working group plans to achieve a standard by March 2003. This preliminary schedule, and the clear benefits of RPR technologies, suggests that pre-standard products will be in widespread use before the standard is finished.
CONCLUSION
Fiber Rings are extremely common in the metro and other networking environment. The time is ripe for a transport technology that both fully exploits the potential of ring networking, and is also easy to integrate with existing Ethernet and SONET technology. RPRs provide a reliable, efficient, and service-aware transport for both enterprise and service-provider networks. Combining the best features of legacy SONET/SDH and Ethernet into one layer, RPR maximizes profitability while delivering carrier-class service. RPR will enable the convergence of voice, video and data services transport.
GLOSSARY
10 Gigabit Ethernet (10GbE) ” The emerging IEEE standard for Ethernet operation at 10 Gbps.
Add/Drop Multiplexer (ADM) ” A multiplexer capable of extracting or inserting lower-rate signals from a higher-rate multiplexed signal without completely demultiplexing the signal.
Asynchronous Transfer Mode (ATM) ” A cell-based, fast packet technology that provides a protocol for transmitting voice and data over high-speed networks. ATM is a connection oriented technology used in both LAN and WAN environments. It is asynchronous in that the recurrence of cells depends on the required or instantaneous bit rate.
Border Gateway Protocol (BGP) ” Protocol for communications between a router in one autonomous system and routers in another.
Carrier Sense Multiple Access/Collision Detection (CSMA/CD) ” A channel access mechanism wherein devices wishing to transmit first check the channel for a carrier. If no carrier is sensed for some period of time, devices can transmit. If two devices transmit simultaneously, a collision occurs and is detected by all colliding devices, which subsequently delays their retransmissions for some random length of time. CSMA/CD access is used by Ethernet and IEEE 802.3.
Data Link Layer”Layer 2 of the OSI reference model. This layer takes a raw transmission facility and transforms it into a channel that appears, to the network layer, to be free of transmission errors. Its main services are addressing, error detection, and flow control.
Ethernet ” (1) A baseband LAN specification invented by Xerox Corporation and developed jointly by Xerox, Intel, and Digital Equipment Corporation. Ethernet networks operate at 10 Mbps using CSMA/CD to run over coaxial cable. Ethernet is similar to a series of standards produced by IEEE referred to as IEEE 802.3.
(2) A very common method of networking computers in a local area network (LAN). Ethernet will handle about 10,000,000 bps and can be used with almost any kind of computer.
Fast Ethernet” Term given to IEEE 802.3u (called Fast Ethernet) for Ethernet operating at 100 Mbps over Cat-3 or 5 UTP.
Fiber Distributed Data Interface (FDDI)”An emerging high speed networking standard. The underlying medium is fiber optics, and the topology is a dual-attached, counter-rotating Token Ring. FDDI networks can often be spotted by the orange fiber "cable." The FDDI protocol has also been adapted to run over traditional copper wires. An ANSI-defined standard specifying a 100 Mbps token-passing network using fiber-optic cable. Uses a dual-ring architecture to provide redundancy.
Fiber Optic Cable”A transmission medium that uses glass or plastic fibers, rather than copper wire, to transport data or voice signals. The signal is imposed on the fiber via pulses (modulation) of light from a laser or a light-emitting diode (LED). Because
of its high bandwidth and lack of susceptibility to interference, fiber-optic cable is used in long-haul or noisy applications.
Fiber Optics”A method for the transmission of information (sound, pictures, data). Light is modulated and transmitted over high purity, hair-thin fibers of glass. The bandwidth capacity of fiber optic cable is much greater than that of conventional cable or copper wire.
Gigabit Ethernet”A 1Gbps standard for Ethernet.
Gigabits Per Second (Gbp/s)”Billion bits per second. A measure of transmission speed.
IEEE 802.1p”An IEEE draft standard that extends the 802.1D Filtering Services concept to provide both prioritized traffic capabilities and support for dynamic multicast group establishment.
IEEE 802.2”IEEE LAN protocol that specifies an implementation of the logical page link control sub layer of the page link layer. IEEE 802.2 handles errors, framing, flow control, and the Layer 3 service interface.
IEEE 802.3u”IEEE LAN protocol that specifies an implementation of the physical layer and MAC sub layer of the page link layer. IEEE 802.3 uses CSMA/CD access at a variety of speeds over a variety of physical media. One physical variation of IEEE 802.3 (10Base5) is very similar to Ethernet.
IEEE 802.5”The Token Ring protocol. IEEE 802.5 uses token passing access at 4 or 16 Mbps over shielded twisted pair wiring and is very similar to IBM Token
Ring.
IEEE 802.17 ” IEEE standard to create a resilient packet ring technology.
Institute of Electrical and Electronic Engineers (IEEE)” Professional organization that defines network standards. IEEE LAN standards are the predominant LAN standards today, including protocols similar or virtually equivalent to Ethernet and Token Ring.
Media Access Control (MAC)”IEEE specifications for the lower half of the data page link layer (layer 2) that defines topology dependent access control protocols for IEEE LAN specifications.
Media Access Control Sub Layer (MAC Sub layer) ” As defined by the IEEE, the lower portion of the OSI reference model data page link layer. The MAC sub layer is concerned with media access issues, such as whether token passing or contention will be used.
Media Independent Interface (MII)”The standard in Ethernet devices to transparently interconnect the MAC sublayer and the PHY physical layer, regardless of media.
Media Interface Connector (MIC)”FDDI de facto standard connector. Megabit (Mb/s) ” One million bits per second.
Megabits per Second (Mbps)”A digital transmission speed of millions of bits per second.
Metropolitan Area Network (MAN)”A data communication network covering the geographic area of a city (generally, larger than a LAN but smaller than a WAN).
Multiple Protocol Label Switching (MPLS)”A set of IETF standards that are designed to allow packet flows to be switched on the basis of labels instead of the full destination addresses, thereby promoting higher performance and allowing traffic engineering.
Multicast ” General term referring to a message intended for receipt by multiple parties.
Open Shortest Path First (OSPF) ” A routing protocol used in IP networks.
Operations Administration Maintenance and Provisioning (OAM&P)”Tasks
performed by the management and administrative systems in a network, especially with reference to public networks.
Optical Add Drop Multiplexer (OADM)”An ADM used with fiber optics.
Optical Cable Level 3 (OC-3)”Defined standard for the optical equivalent of Synchronous Transport Signal 3 (STS 3) transmission rate or STS 3c Synchronous Optical Network Transport Systems (SONET) transmission rate. The signal rate for these standards is 155.52 Mbps.
Optical Carrier 1 (OC-1)”ITU-ISS physical standard for optical fiber used in transmission systems operating at 51.84 Mbps.
Optical Carrier 3 (OC-3)”Optical Carrier level 3, SONET rate of 155.52 Mbit/s, matches STS-3.
Optical Carrier- N (OC-N)”Higher SONET level, N times 51.84 Mbit/s.
Physical Coding Sublayer (PCS) ” One of the sublayers defined for the Ethernet protocol stack.
Physical Layer (PHY) ” The bottom layer of the OSI and ATM protocol stack, which defines the interface between ATM traffic and the physical media. The PHY consists of two sublayers: the transmission convergence (TC) sublayer and the physical medium-dependent (PMD) sublayer.
Points of Presence (POP) ” A term used by Internet service providers to indicate the number of geographical locations from which they provide access to the Internet.
Protocol Data Unit (PDU)”A discrete piece of information like a frame or a packet in the appropriate format for encapsulation and segmentation in the payload of a cell.
Packet Ring ” Refers generally to technologies which transmit information in packet form but are optimized for a ring topologies. Examples include the emerging RPR / 802.17 standard, and Token Ring technology.
Resilient Packet Ring (RPR) ” A term that refers to the specific efforts of the IEEE 802.17 working group to generate a resilient packet ring protocol for Wide and Metro Area networks.
Quality of Service (QoS) ” Term for the set of parameters and their values which determine the performance of a given virtual circuit.
Shared Ethernet”Conventional CSMA/CD Ethernet configuration to which all stations are attached by a hub and share 10 or 100 Mbps of bandwidth. Only one session can transmit at a time. This is the most popular network type today
Spatial Reuse Protocol (SRP) ” A proprietary Cisco packet ring technology.
Synchronous Digital Hierarchy (SDH) ” ITU-TSS international standard for transmission over optical fiber.
Synchronous Optical Network (SONET) ” A set of standards for transmitting digital information over optical networks. "Synchronous" indicates that all pieces of the SONET signal can be tied to a single clock. A CCITT standard for synchronous transmission up to multigigabit speeds
Time Division Multiplexing (TMD)”A form of transmission in which different flows are combined on the basis of time slots.
Token Ring ” Refers to the packet ring technology defined in IEEE 802.5 and elsewhere, intended for use in local area networks. On a token ring, transmission on the ring is mediated by nodes sequentially passing a token which allows the possessor to broadcast on the ring.
Transport Control Protocol/Internet Protocol (TCP/IP)”A protocol (set of rules) that provides reliable transmission of packet data over networks.
Wide Area Network (WAN)”A network which encompasses interconnectivity between devices over a wide geographic area. Such networks would require public rights-of-way and operate over long distances.
Wave Division Multiplexing (WDM)”A technology that allows multiple wavelengths to be multiplexed over a single strand of fiber. Comes in various forms including Dense and Wide depending on the number of wavelengths involved.
REFERENCES
¢ rpralliance.com
¢ iec.org
¢ itpapers.com
¢ techguide.com
¢ howstuffworks.com
CONTENTS
1. INTRODUCTION
2. LIMITATIONS OF SONET AND ETHERNET
3. RPR OPERATIONS
4. ADVANTAGES OF PACKET RING NETWORK
5. STANDARDIZATION
6. CONCLUSION
7. GLOSSARY
8. REFERENCE
Reply
#3
i want effective methods of software testing ebook by e.perry 2nd edition
Reply
#4
i want effective methods of software testing ebook by e.perry 2nd edition
Reply
#5
[attachment=6531]
PRESENTED BY:-

APARNA.N
M.C.A.III YEAR
ROLLNO : 1
B.E.C
BAPATLA

LAN TOPOLOGY


INTRODUCTION:



Data communication is the active process of transferring data from one point to another. A "LINK" is a physical communication pathway that transfers data from one device to another.

A "COMPUTER NETWORK" is a collection of computers and perpheral devices (network components) connected by a communication links that allows the network components to work together. The network components may be located at any remote location or in the same location. In any case data communication is the glue that holds the network together.

One such network is a "LOCAL AREA NETWORK" a communication system which permits the inter connection of networks. The computers in a network may be connected in various ways. A LAN is inter-linked system where personal computers share common resources like disks, printers etc...

"TOPOLOGY" can be defined as the geometric arrangement of wofkstations and the links among them. Various topologies include Bus, Ring, Star, Tree, Mesh and Hybrid topologies. It is called the structure of the network.

Line Configuration:

It refers to the way wo or more devices attach to a disk.

Point-to-Point Line Configuration:

It provides a dedicated page link between tow devices. The entire capacity of the channel is reserved for transmission between those two devices.

Multi Point Line Configuration:

It is the one in which more than two devices share a common link.

Work Station:

A workstation is any personal computer capable of supporting the hardware and software necessary to connect in a LAN.

User work station or Client:

These are the micro computers on the network, which have a primary responsibility to an individual user.

Server work station:

Resources attached to server are shared by all users. They serve to other workstation.



Reply
#6
[attachment=9444]
1. INTRODUCTION
Over the fast few years, new promising protocols have emerged at the forefront of Metro Networking. One among them is the Resilient Packet Ring Technology (RPR). Today, as the standards slowly settle, it is finally reaching the stage beyond specification, and into network deployment.
RPR is a MAC layer technology standardized by the IEEE 802.17 workgroup. It is independent of the physical layer and can run on SONET/SDH, Ethernet and Dense Wavelength Division Multiplexing.
Integrating the high reliability of SDH self-healing and Ethernet advantages such as low cost, large bandwidth, flexibility, and scalability, the RPR technology provides bandwidth management with data optimization capability and high performance multiservice transmission on a ring topology. RPR technology, on their own, adds features to Metro Area Networks that are currently lacking.
2. RPR TECHNOLOGY
The rapidly increasing volume of data traffic in metro networks is challenging the capacity limits of existing transport infrastructures that are based on circuit-oriented technologies like SONET and ATM. Packet-based transport technology is considered by many to be the likely alternative for scaling metro networks to meet traffic demands.
2.1. Overview of RPR Technology
RPR Technology is an emerging solution for metro data transport applications that can fully exploit fiber rings. It retains all the inherent advantages of a packet-based transport mechanism like Ethernet. This latest technology is suitable for data, voice, and video applications. The adoption of RPR technology is particularly critical to handle the rapid growth of data traffic in metropolitan networks.
RPR technology reduces operational and equipment costs, increases resiliency to faults and provides higher throughput, while allowing for rapid deployment and efficient bandwidth allocation. RPR technology is being designed specifically for metropolitan area networks of fiber optic rings and will be an important part of new metropolitan data networks. This new protocol will allow metropolitan area service providers to create high-speed, survivable ring networks optimized for IP and other packet data.
Structure Overview
RPR is a reciprocal dual-ring topology, with each optical span working at the same rate. The difference is that both the two rings of RPR can transmit data. These two rings are referred to as Ringlet0 and Ringlet1 respectively.
Data are transmitted clockwise on Ringlet0 while anti-clockwise on Ringlet1.
Each RPR station uses a 48-bit MAC address used in Ethernet as its address ID. From the perspective of the page link layer of the RPR station, these two pairs of physical optical ports of transmission/reception are only one page link layer interface. From the perspective of the network layer, only one IP address needs to be allocated.
The page link between two adjacent RPR stations is refereed to as a span, and multiple continuous spans and the stations on them constitute a domain.
From the perspective of a station, its packet switching structure has changed immensely in comparison with the traditional packet switching structure.
This structure is similar to the ring road of a city, where the stations on the ring are directly connected, with barely any traffic lights needed, and hence higher efficiency. One RPR station has one MAC entity and two physical layer entities. The physical layer entities are associated with the links. Referred to as the access point, the MAC entity includes one MAC control entity and two MAC service page link entities. Each access point is associated with a loop. By direction, physical layer entities are divided into east physical layer and west physical layer. The east and west are based on the assumption that the station is to the north of RPR. The “Tx interface” of the east physical layer and the “Rx interface” of the west physical layer are connected via the MAC entity into the Ringlet0 of RPR. Similarly, the “Rx interface” of the east physical layer and the “Tx interface” of the west physical layer are connected into the Ringlet1 of RPR.
2.2. Key Features of RPR Technology
• Efficient support for ring topology.
• Increases resiliency to faults and provides higher throughput. Fast recovery from fiber cuts and page link failures.
• Data efficiency, simplicity, and cost advantages.
• Problems such as fairness and congestion control solved.
• Efficient bandwidth allocation.
2.3. Basic Ring Operation
Resilient Packet Rings (RPR) are data optimized networks, with at least two counter-rotating fiber ringlets in which multiple nodes share the bandwidth without the requirement of provisioning circuits.
In agreement with the ring, the stations are designed with ADM data switching for various data operations. Common basic data operations are:
Insert: It is the process that the station equipment inserts the packets forwarded from other interfaces into the data stream of the RPR ring;
Copy: It is the process that the station equipment receives data from the data stream of the RPR ring and gives them to the upper layer for processing;
Transit: It is the process that the data stream passing a station is forwarded to the next station;
Strip: It is the process that the data passing a station is stopped from further forwarding.
The data operation for “transit” is similar to that of the SDH ADM equipment, in that the “transit” data streams are not processed by the upper-layer equipment, which greatly enhances the processing performance of the equipment. Such ADM switching of packets can easily support various high-speed page link interfaces.
The stations use one or any combination of these basic data operations to implement unicast, multicast and broadcast traffic.
Reply
#7
presented by:
Anusha P Vijayan

[attachment=9450]
RPR Introduction
 Packet based ring network for Metropolitan Area Networks (MANs)
 Support up to 255 station attachments
 Optimized for rings with maximum circumference of 2000 kilometers
SONET in MAN
 SONET is designed for point-to-point, circuit-switched applications
Some of the disadvantages are
 Fixed Circuits
 Wasted Bandwidth for Meshing
 Multicast Traffic
 Wasted Protected Bandwidth
 Ethernet in MAN
 Ethernet over a ring
 Make efficient use of available bandwidth
 Far simpler and inexpensive solution for data
 Optimized for point-to-point or meshed topologies
 Disadvantages
 Not take advantage of ring topology to implement fast protection mechanism
 Slow recovery from fiber cuts
 No global fairness policy
RPR Operation
 Uses a dual counter rotating fiber ring topology
 Utilizes the total available ring bandwidth
 The fibers or ringlets are used to carry the control messages
 RPR has the ability to differentiate between low and high priority packets
The RPR MAC
 The MAC layer contains much of the functionality for the RPR network
 It is responsible for providing access to the fiber media
 It can receive, transit and transmit packets
MAC Frame format
Advantages of Packet Ring

 Each node can assume that a packet sent on the ring will eventually reach it’s destination node regardless of the path taken
 Only three basic packet-handling actions are needed:
Insertion
Forwarding
Stripping
 Reduces the amount of work individual nodes have to do
RPR Characteristics
 Resiliency
 Bandwidth fairness
 Broadcast or multicast traffic
 Physical layer versatility
Resiliency
 Ring built using switches needs to distribute failure information across an entire network to recover fully from fiber cuts
 Packet ring protocol can use a “ring wrap” at the nodes surrounding the cut
 Ring failure is often described as “self healing” or “automatic recovery”
Bandwidth Fairness
 Implement fairness algorithms to regulate bandwidth usage
 A fairness algorithm is a mechanism that gives every node on the ring a predetermined “fair” share of the ring bandwidth
 A ring level fairness algorithm can and should allocate ring bandwidth as one global source
Broadcast or Multicast Traffic
 Packet rings are natural fit for the broadcast and multicast traffic.
Physical layer versatility
 Packet ring standards in development create only a new MAC addressing scheme, that has the advantage of leaving layer 1 open
 Packet ring technologies will be compatible with Ethernet, SONET and DWDM physical layer standards
 A dark fiber is available, a packet ring can operate without the need to purchase expensive layer 1 gear
Disadvantages of RPR
 Higher system cost due to the additional MAC layer
 Without a cross-ring standard, RPR information cannot be transferred from one ring to another
 RPR uses a shared access mode, and has only one layer of MAC address forwarding. Therefore, network and service expansibility is somewhat limited.
Packet rings in application
 Packet rings suit the needs of many types of service providers in the metro area
 A single packet ring serves the needs of multiple buildings in a metro area
 This solution has several notable features
1. the packet ring at the centre of this solution will allow the service provider to sell true protected bandwidth to the end users
2. Prevent any single node “starving” other nodes
3. Small form-factor packet ring routers will mean mode equipment that can easily fit into existing configured spaces
4. The presented solution demonstrates a healthy integration of Ethernet and packet ring technologies
Standardization
Some of the goals of the 802.17 working groups are:
1) Support for dual counter rotating ring topology
2) Full compatibility with IEEE’s 802 architecture as well as 802.1D,802.1Q and 802.1f
3) Protection mechanism with sub 50ms fail-over
4) Destination stripping of packets
5) Adoption of existing physical layer medium to avoid technical risk
Conclusion
 RPR is a MAC protocol and operates at Layer 2 of the OSI protocol stack
 By design RPR is a Layer 1 agnostic, which means that RPR can run over either SONET or Ethernet
 RPR enables service providers to build more scalable and efficient metro networks using SONET or Ethernet as physical layers
The time is ripe for a transport technology that both fully exploits the potential of ring networking and is also easy to integrate with existing Ethernet and SONET
Reply
#8
to get information about the topic Resilient Packet Ring Technology full report ppt and related topic refer the page link bellow

http://studentbank.in/report-resilient-p...logy--5301

http://studentbank.in/report-resilient-p...logy--4224

http://studentbank.in/report-resilient-p...ogy--28206

http://studentbank.in/report-resilient-p...301?page=2

http://studentbank.in/report-resilient-p...ull-report
Reply

Important Note..!

If you are not satisfied with above reply ,..Please

ASK HERE

So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page
Popular Searches: congestion control in resilient packet rings, rpr abbreviation, resilien packet ring technology ppt free download, resilient packet ring network ppt, resilent packet ring technology abstract, what was the mans, most resilient animal,

[-]
Quick Reply
Message
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  5G technology dhanya1987 8 12,932 11-04-2016, 11:21 AM
Last Post: dhanabhagya
  FinFET Technology computer science crazy 13 11,637 10-03-2015, 04:38 PM
Last Post: seminar report asees
  Cellonics Technology computer science crazy 3 3,539 05-09-2014, 09:45 PM
Last Post: seminar report asees
  Latest Invention: Acoustic Ear-scanning Technology to Help Avoid Theft project report helper 10 8,681 20-08-2014, 09:02 PM
Last Post: preethikrishna
  RFID Technology computer science crazy 4 4,634 09-08-2014, 07:10 PM
Last Post: Guest
  Seminar Report On Optical Computing Technology mechanical wiki 3 5,887 27-07-2013, 12:41 PM
Last Post: computer topic
Question Sixth Sense Technology nitins60 43 76,220 22-06-2013, 10:46 AM
Last Post: Guest
  Blue Eyes Technology sprity 21 31,226 30-01-2013, 12:54 PM
Last Post: seminar details
  3G MOBILE COMMUNICATION TECHNOLOGY full report seminar presentation 22 31,253 29-01-2013, 11:06 AM
Last Post: seminar details
  Cellonics Technology computer science crazy 25 28,446 10-01-2013, 03:34 PM
Last Post: seminar details

Forum Jump: