20-04-2017, 11:11 AM
DEPUTY ENGINEER - GENERAL AND SOCIETY CATEGORY - KERALA CO-OPERATIVE MILK MARKETING FEDERATION LTD.pdf (Size: 1.45 MB / Downloads: 1)
1.Zeroth law of thermodynamics defines :
(A)internal energy(B) temperature
(C ) enthalpy(D) pressure
2.Otto cycle is also known as :
(A)constant temperature cycle
(B)constant temperature and pressure cycle
(C )constant volume Cycle
(D)constant pressure cycle
3.The Kinematic viscosity can be defined as the :
(A)ratio of absolute viscosity to the density of the liquid
(B)ratio of density of the liquid to the absolute viscosity
(C )product of absolute viscosity and density of the liquid
(D)product of absolute viscosity and mass of the liquid
4.The action of a centrifugal pump is the :
(A)reverse of a mixed flow type turbine
(B)reverse of propeller type turbine
(C )reverse of a radially inward flow' reaction turbine
(D)reverse of a reciprocating pump
5.Basic closed cycle for Gas Turbine is :
(A) Carnot cycle(B)Rankine cycle
(C ) Stirling cycle(D)Bray ton cycle
6.The quantity of radiation heat flux depends on
(A) The shape of the body only(B)Temperature of the body only
(C ) Area of the body only(D)All of the aboveAll of the above
7.Interior wall is at 1000°C The wall thicknessis 0.6m, it is 1 m wide and 1.5 m broad of
material with thermal conductivity 0.4 W/m ° Then the thermal resistance is :K. The temperature of-outside wall is 200°C
(A) 1°KAV(B)2°KAV
(C ) 1.8°K/W(D)1.5°KAV
8. According to Stefan-Boltzmann law, the total radiation from a black body per second per unit area is______________fourth power of the absolute temperature.
(A) equal to(B)directly proportional todirectly proportional to
(C ) inversely proportional to(D)exponential to
9.Forging results in the following :
(A) reduces the mechanical properties(B)improves the grain flow
(C ) creates internal defects(D)all of the aboveall of the above
10.In Electrical discharge machining :
(A)the work piece and tool must both conduct electricity (13) only the work piece conducts electricity
(C )only the tool conducts electricity
(D)both tool and work piece should not conduct electricity
11. In a tensile test, necking starts at:
(A)lower yield stress(B)upper yield stressupper yield stress
(C )ultimate tensile stressultimate tensile stress(D)just before fracturejust before fracture
12.The fatigue strength of mild steel is :
(A)equal to its tensile strength(B)more than its tensile strength
(C )equal to its yield strengthequal to its yield strength(D)lower than its yield strengthlower than its yield strength
13.The power transmitted by belt drive is designed on thebasis of:
(A)angle of contact on the larger pulley
(B)angle of contact on the smaller pulley
(C )average angle of contact on the two pulleys
(D)angle of contact on the driver pulley, whether smaller or larger
14.Dynamometer is a device for measuring :
(A)torque exerted by the machine
(B)power developed by the machinepower developed by the machine
(C )power absorbed by the machine
(D)all of the aboveall of the above
15.The typeof gears used to connect two non-parallel non-intersecting shafts are :
(A)straight spur gears(B)straight bevel gearsstraight bevel gears
(C )cross helical gearscross helical gears(D)spiral gearsspiral gears
16.Ammonia, which is used as a common refrigerant, has a normal boiling point of:
(A)-39.6°C(B) 31.7°C
(C ) -3.1°C(D) -33.3°C
17.Specific humidity (humidity ratio) is the ratio of:
(A)Mass of water vapour present per kg of dry air
(B)Mass of water vapour present in unit volume of air
(C )Actual mass of water vapour in a given volume to the mass of water vapour if the air is saturated at the same temperature
(D)None of the above
18.Calorific value of dry wood is
(A)3400 kcal/kg
(C )9100 kcal/kg
19.Reciprocating pump falls under the category' of:
(A)Rotodynamic pumps
(B)Dynamic-pressure pumps
(C )Positive displacement pumps
(D)All of the above
20.In reaction turbines, the pressure at the inlet of the turbine :
(A)is much higher than that at the outlet
(B)is much lower than that at the outlet
(C )is equal to the outlet pressure
(D)is initially lower than the outlet and then increases
21.Hysteresis loss in electrical systems is directly proportional to the :
(A)Frequency and flux density
(B)Frequency, and flux density to the power 1.6
(C )Square of frequency, and flux density to the power 1.6
(D)Square of frequency, and square of flux density
22.If speed of dc motor increases with load torque, then it is a :
(A) Series motor(B) Brushless motor
(C ) Cumulatively compounded motor(D) Differentially compounded motor
(B)1300 kcal/kg
(D)2500 kcal/kg
23.The power electronic switch used for a Sine-PWM inverter can be :
(A) SCR(B) TRIAC
(C ) IGBT(D) All of these
24.Which of the following statement is correct for a common base transistor amplifier?
(A)High current gain and high output impedance
(B)Low input impedance and high output impedance
(C )High input impedance and low output impedance
(D)High voltage gain and low output impedance
25.If common base current gain a = 0.99, ICBO = 5juA, IB = 50 juA for a bipolar transistor, then value or collector current Ic will be :
(A) 5.5 mA(B) 4.5 mA
(C ) 5.0 mA(D) 2.5 mA
26.A second order RLC series circuit behaves like an inductive circuit:
(A)At resonant frequency
(B)Below resonant frequency
(C )Above resonant frequency
(D)At lower half power frequency
27.3- phase transformer combinations which cannot be operated in parallel are :
(A)Star- star & delta- delta
(B)Star-delta & delta-star
(C )Star-star & star-delta
(D)Delta-delta & star-star
28.Mho relay is normally used for the protection of:
(A)Long transmission line
(B)Short transmission line
(C )Transformer
(D)DC motors
29.A 1 mA d’ Arsonval ammeter has required to convert it to a (0-50) V
(A)1 k Ω
(C )4.9 k Ω
(B)49.9 k Ω
(D)10 k Ω
30.During frequency measurement Lissajous pattern on oscilloscope has 2 horizontal tangencies and 5 vertical tangencies when the frequency of the horizontal input is 1 kHz. Then the vertical frequency will he :
(A)5.0 kHz(B)2.5 kHz
(C )4.0 kHz(D)400 Hz
31.A two port network is defined by the following equations, IL = Vq-O.oV^, /2 =-Iq I V2, Z parameters are given by Z = :
(A)[1 -0.5;-1 1](B)[2 1; 22]
(C )[1 -2;-11](D)[1 2; 2l]
32.A capacitor of 10 /jF is connected to a 100 V dc source through a series resistance of 10 kΩ It will be fully charged in :
(A)0.01 s(B)0.1 s
(C )0.158 s(D)0.5 s
33.A step up chopper supplying a load at 500V and input is 200V. The off time of switch is 20pusec, inductor current is continuous and ripple free. The frequency of chopper in kHz is :
(A)20 kHz(B)25 kHz
(C )50 kHz(D)100 kHz
34.The two windings of a 200/100 V transformers are connected in series and results in net inductances of 70 mH and 30 mH in different connections Assuming Ll = 4L2, the coupling coefficient is :
(A)1(B) 0.5
(C ) 0.25(D) 0.128
35.Among the following materials cable glands are made from:
(i)plastic(ii)Brass
(iii)Aluminium(iv)Stainless steel
(A)All theabove(B)(ii) & (iv)
(C )(ii) (iii)& (iv)(D)(iv) only
36.A voltage source with source impedance Zs = 0.3 + y’0.4Ω2is connected to a resistive load. Then the load resistance for maximum power transfer is :
(A) 0.3 Ω(B) 0.4 Ω
(C ) 0.7 Ω(D) 0.5 Ω
37.The maximum allowable earth resistance for major substations is :
(A)1 Ω(B) 5 Ω
(C ) 25 Ω(D) OΩ
38.The line voltage Vky is 400Z0 V for a balanced 3-ph star-connected load with phase sequence RYB. Then the phase voltage Vbn is given by :
(A)230<90(B)230< -120
(C )230<-90(D)100<30
39.A 50 MV A, 22 kV synchronous generator has 0.2 Pu synchronous reactance. The pu synchronous reactance on the base values of 100 MVA and 11 kV is :
(A)1.6(B)0.1
(C )4.0(D)0.2
40.A thyrite type lightning arrestor :
(i)uses a Silicon Carbide basedmaterial
(ii)acts as a nonlinear resistor
(iii)offers a low resistance path to the surge appearing in the line
(iv)returns surge back to the source Among the above four statements.
(A) All are correct(B) (i) and (iv) are correct
(C ) (i), (ii), and (iii) are correct(D) (ii), (iii) and (iv) are correct
41.Which of the following wood is more resistant to white ants?
(A)Teak(B)Sal
(C )Deodar(D)Chir
42.A steel rod of 2cm2 area and lm in height is subjected to a pull of 40000 N. If Young’s modulus is 2 x 106 N/mm2, the elongation of the rod will be :
(A)10 mm
(C ) 1 mm
(B)100 mm
(D)0.1 mm
43.The elastic constant which gives the relation between pressure and change in volume
(A) Young’s modulus(B) Rigidity modulus
(C ) Bulk modulus(D) Poisson’s Ratio
44.Where the intensity of load is constant, Bending Moment will vary :
(A)Constant(B)Linearly
(C )Parabolically(D)Cubically
45.Moment of Inertia of triangular section with base b and height h about base will be :
(A)bh3/3(B)bh3/i2
(C )bh*/36(D)bh3/6
46.The shear stress in a circular shaft of radius r subjected to torsion is maximum :
(A)at centre of shaft(B)at a distancer/2 fromcentre of shaft
(C )at surface of shaft(D)at a distancer/2 fromsurfaceof shaft.
47.A simply supported rectangular beam is loaded transversely, the maximum tensile stress develops at:
(A)bottom fibre(B)top fibre
(C )neutral axis(D)no tensile stress
48.A surface vibrator for concrete compaction is preferred for all the following except:
(A)raft foundation(B)columns
(C )road pavements(D)R.C.C. slabs
49.Maximum gross pressure which the soil can carry safely without shear failure :
(A)Gross safe bearing capacity(B)Net safe bearing capacity
(C )Ultimate Bearing capacity(D)Net ultimate bearingcapacity
50.Type of foundation suitable when the load is heavy and the soil is highly compressible :
(A)Mat foundation(B)Pile foundation
(C )Pier foundation(D)Well foundation
51.The property of cement tested by using Lechatelier apparatus :
(A)consistency(B)setting time
(C )compressive strength(D)soundnesssoundness
52.The discharge through a V-notch varies as :
(A)H(B)H1/2
(C )H3/2(D)H3/2
53.Hydraulic jump is used for :
(A)increasing the depth of flow(B)reducing the energy of flow
(C )decreasing the velocity of flow(D)reducing the turbulencereducing the turbulence
54.An example of steady non-uniform flow is :
(A)motion of a river around bridge piers
(B)steadily increasing flow through a pipe
(C )steadily decreasing flow through a reducing sectionsteadily decreasing flow through a reducing section
(D)constant discharge through a long,straight tapering pipeconstant discharge through a long, straight tapering pipe
55. For steady rotational flow of a fluid Bernoulli’s equation :
(A)cannot be derived
(B)can be derived for the entire flow field
(C )can be derived only if the fluid is incompressible
(D)can be derived only for the points lying on the same stream
56. As per ISI, concrete should be cured under a humidity of:
(A) 20%(B)98%
(C ) 50%(D)90%90%
57.Low heat cement is suitable for :
(A) thin structure(B)thick structurethick structure
(C ) R.C.C. structure(D)underwater structureunderwater structure
58.For construction of structures under water, the lime used is :
(A) fat lime(B)quick limequick lime
(C ) hydraulic lime(D)pure limepure lime
59.Efflorescence is caused by :
(A) low silica content of bricks(B)presence of alkali saltspresence of alkali salts
(C ) high pH of water used for pugging(D)all the aboveall the above
60Stone generally preferred for railway ballast is :
(A) basalt(B)marble
(C ) slate(D)sand stonesand stone
61.Fluid milk plants should be located near the :
(A) Dairy Farm(B)Milk consumption area
(C ) Industrial area(D)None of theseNone of these
62.Which among the following is the most suited material for the floor of the dairy plant?
(A) Mandana Tiles(B)concrete TilesConcrete Tiles
(C ) Marble(D)Stainless steel
63.Which type of pump is suited for transfer of rawmilk from reception dock to storage silos?
(A) Rotary(B)Reciprocating
(C ) High pressure(D)Centrifugal
64.ne separators are associated with :
(A) Cream separator(B)Drum drier
(C ) Spray drier(D)Tray drierTray drier
65.In evaporators used in food industry, the heating medium used is mainly :
(A) Hot water(B)Steam
(C ) Hot air(D)Hot oil
66.Reverse osmosis technique is mainly used for :
(A) Concentration(B)Filtration
(C ) Separation(D)None of theseNone of these
67.In GIF system, protein residue is best cleaned by
(A) Alkali(B)Steam
(C ) Acid(D)Hot water
68.Final stage of treatment in a Mechanical can washer is treatment with :
(A) Cold water(B)Sanitizer
(C ) Warm water(D)Steam
69.The leak proofness of milk pouches are tested by:The leak proofness of milk pouches are tested by
(A) Squeeze test(B)Tear Test
(C ) Drop test(D)All of theseAll of these
70.Homogenization divides the fat globules to the size :
(A)1 o *(B)< 10 puM
(C ) >10 puM(D)< 1 puM
71.The process of removal of bacteria from milk by centrifugal force is called :
(A) Centrifugation(B)Bactofugation
(C ) Fumigation(D)None of theseNone of these
72.Ice thickness controller is used in :
(A) Ice Bank Tank(B)Butter cold store
(C ) Ice cream Freezer(D)Milk chilling roomMilk chilling room
73.Milk cold room is maintained at:
(A) 1°C(B)- 50°C
(C ) -20°C(D)20°C
74.Double ‘O’ vat is related to :
(A) Butter making(B)Cheese making
(C )Cream separationCream separation(D)Sterilization
75.A device widely used for removing condensate is:
(A)Condenser(B)Evaporator
(C )Steam trap(D)Filter
76.The optimum temperature for efficient homogenizationis :
(A)10°C(B)45 °C
(C )25 °C(D)65 °C
77. The steam required to evaporate one kg of water from milk is around triple effect evaporator.
(A) 0.4 kg(B)1.0 kg
(C ) 1.2 kg(D)2.0 kg
78.AISI 304 steel consists of:
(A) 18% Nickel and 80% Chromium(B)18% Chromium and 8% Nickel
•(C ) 10% Nickel and 10% Chromium(D)None of these
79The speed of rotation in a centrifugal atomizer is:
(A) 1000 - 2000 rpm(B)30,000 rpm
(C ) 50,000 rpm(D)6,000 - 20,000 rpm
80.The time - temperature combination for HTST pasteurization is :
(A) 63 °C / 15 seconds(B)63 °C/30 minutes
(C ) 72 °C/ 15 seconds(D)72°C/30 minutes
81.Recently, WHO - India has launched IVR 2020 programme to protect and increase number of:
(A) Tigers(B)One -horn Rhinos
(C ) Indian Bustard(D)Asiatic lions
82.Which among the following dates is observed as Anti -Leprosy Day in India?
(A) January 30(B)February 15
(C ) March 11(D)April 6April 6
83.Who among the following was first cinematographer to be chosen for the prestigious Dhada Saheb Phalke award?
(A) Govind Nihalani (C ) B.C. Gowrishankar
(B) B.S. Lokanath (D) V.K Murthy
84.The inventor of the World Wide Web has marked the 25th anniversary of his creation by calling for a ‘Magna Carta’ bill of rights to protect its users. Identify him from the given options :
(A) Tim — Berners - LEE(C ) Robert Taylor
(B) Stuart Harris (D) Claude Shannon
85.Wisden’s Five Cricketer of the year of 2013 has been awarded to :
(A) Vi rat Kohli(B) Rohit Sharma
(C ) Shikar Dhawan(D) Suresh Raina
86.Lee Run—hee, who is facing an arrest warrant in a 1.4 million dollar cheating case is chairman of:
(A) Nokia (C ) LG
(B)Samsung
(D)IBM
87.“Jens stoltenberg” who has been elected as NATO chief is the former Prime Minister of:
(A)Norway(B)Russia
(C )Germany(D)USA
88.In context to astronomy, “Charkilo” which is in news recently is :
(A)comet(B)miniatureplanet
(C )meteorite(D)asteroid
89.Who shared the Best actor National Award of the year for 2013?
(A)Fahed Fazil(B)Lal
(C )Suraj Venjaramoodu(D)Jayaram
90.The state which is known as ‘Jw'el of India’:
(A)Meghalaya(B)Arunachal Pradesh
(C )Assam(D)Manipur
91.Who was considered as father of Demography?
(A)Dr. Montek Singh(B)Jim yong kim
(C )Shyam Prasad Gupta(D)John Graund
92.Who was the viceroy of India When Congress formed?
(A) Lord Curzon(B)Lord Delhousie
(C ) Lord Dufferine(D)Lord Mayo
93.Jallianwallabag Tragedy was occurred in :
(A) 1919(B)19111911
(C ) 1909(D)19211921
94.The river called as Ganga of Kerala :
(A) Kahani(B)Kaveri
(C ) Bharathappuzha(D)Periyar
95.The colour of Red soil is due to the presence of:
(A) Carbon Sulphate(B)Iron oxideIron oxide
(C ) Methanol(D)Copper oxide Copper oxide
96.Inhabitants of Kurinji during Sangam period is knows as:
(A) Uzhavar(B)Idayar
(C ) Meenavar(D)Vettuvar
97.The amendment of our constitution that made education as a fundamental
(A) 86(B)84
(C ) 68(D)7272
98.The only congress session presided by Mahatma Gandhi:
(A) Nagpur(B)Belgam
(C ) Poona(D)BombayBombay
99.Dharsanamala was the famous work of:
(A) Kumaranasan(B)Dr. Palpu
(C ) Sree Narayana Guru(D)Ayyankali
100.Pallivasal Hydro Electric scheme was inaugurated during the period of:
(A) Chithira Thirunal Balarama Varma(B)Dharma Raja
(C ) Swathi Thirunal(D)Moolam Thirunal