1. INTRODUCTION
Electrical energy is a major requirement for the economic and industrial growth of any country. Most of the electrical energy is generated from the combustion of fossil fuels (coal, oil, gas). The fossil fuels are not only limited in nature, but generating electricity with these fuels have serious environmental, economical and safety consequences.
Energy from the sun, water, wind biomass and the ocean is renewable, biomass clean and environment friends. India has sufficient potential to develop hydro-el ....etc

[:=Read Full Message Here=:]

Definition

Hydro Forming uses water pressure to form complex shapes from sheet or tube material. The pressure may go up about 60,000 psi depending on the component.

As the automobile industry strives to make car lighter, stronger and more fuel efficient, it will continue to drive hydro forming applications. Some automobile parts such as structural chassis, instrument panel beam, engine cradles and radiator closures are becoming standard hydro formed parts.

The capability of hydro forming can be more fully used to create complicated par ....etc

[:=Read Full Message Here=:]

HYDRO POWER PLANT

Presented by:
RITEE

CHHATTISGARH SWAMI VIVEKANAND TECHINICAL UNIVERSITY , BHILAI

INTRODUCTION
HYDRO POWER
1) One of the most widely used renewable source of energy for generating electricity on large scale basis is hydropower
2) The power obtained from river or ocean water is called as hydropower
3) Hydropower is the renewable source of energy since water is available in large quantities from rain, rivers, and oceans and this is ....etc

[:=Read Full Message Here=:]

During the last 12 years, general awareness of hydro forming has grown steadily . Although interest in hydroforming is wide ranging , the vast majority of application are in automobile industry .
Hydro forming is the process by which water pressure is used to form complex shapes from sheet or tube material.Applications of hydro forming in automotive industry are gaining globally in popularity. The trend in auto manufacturing of making parts lighter and more complicated with necessary strength reinforcement only where required is ....etc

[:=Read Full Message Here=:]

i want information regarding micro hydro power plant ....etc

[:=Read Full Message Here=:]

Definition

Hydro Forming uses water pressure to form complex shapes from sheet or tube material. The pressure may go up about 60,000 psi depending on the component.

As the automobile industry strives to make car lighter, stronger and more fuel efficient, it will continue to drive hydro forming applications. Some automobile parts such as structural chassis, instrument panel beam, engine cradles and radiator closures are becoming standard hydro formed parts.

The capability of hydro forming can be more fully used to create complicated par ....etc

[:=Read Full Message Here=:]

Hydro Drive is a drive or transmission system that uses hydraulic fluid under pressure to drive machinery. The term hydrostatic refers to the transfer of energy from flow and pressure, not from the kinetic energy of the flow.consists mainly of three parts. The generator (e.g. a hydraulic pump, driven by an electric motor, a combustion engine or a windmill); valves, filters, piping etc. (to guide and control the system); the motor (e.g. a hydraulic motor or hydraulic cylinder) to drive the machinery ....etc

[:=Read Full Message Here=:]

Among all the substances in the universe, water holds unique incomparable positions. Much more than being a major source of energy, it is the primary cause of all life on earth. Also non-traditional and industrial applications of water such as hydraulic transportation of coal and minerals in slurry form, dredging, sprinkler irrigation, cooling and refrigeration etc. are gradually increasing. So much so that availability of water plays primary role in location of an industry today over all other considerations.


Technological adv ....etc

[:=Read Full Message Here=:]

Hydro Drive

Hydro Forming uses water pressure to form complex shapes from sheet or tube material. The pressure may go up about 60,000 psi depending on the component.

As the automobile industry strives to make car lighter, stronger and more fuel efficient, it will continue to drive hydro forming applications. Some automobile parts such as structural chassis, instrument panel beam, engine cradles and radiator closures are becoming standard hydro formed parts.

The capability of hydro forming can ....etc

[:=Read Full Message Here=:]

Hi...
Im urgently in need of seminar topics of related turbomachinery .... So i selected these topics which are placed topics in this site. If u people hav anymore related topics to turbomachinery please send it to me..:-/ ....etc

[:=Read Full Message Here=:]