INTRODUCTION

1.1 INTRODUCTION

ABSENTEEISM
Absenteeism is one of the most important wide spread obstacle to productivity. The absence may be due to personal problems, sickness, sickness of family members, or any other reason.The absenteeism can be divided as any other reason. The absenteeism can be divided as authorized and unauthorized absenteeism. In the authorized absenteeism the employee notifies the reasons at a reasonable time to the supervisors.

The absenteeism may be due to some uncontrollable eve ....etc

[:=Read Full Message Here=:]

ABSTRACT
When objects move through air, forces are generated by the relative motion between the air and surfaces of the object. Aerodynamics is the study of these forces, generated by the motion of air, usually aerodynamics are categorized according to the type of flow as subsonic, hypersonic, supersonic etc.
It is essential that aerodynamics be taken in to account during the design of cars as an improved aerodynamics in car would attain higher speeds and more fuel efficiency. For attaining this ae ....etc

[:=Read Full Message Here=:]

Airframe
The airframe of an aircraft is its mechanical structure, which is typically considered to exclude the propulsion system. Airframe design is a field of engineering that combines aerodynamics, materials technology and manufacturing methods to achieve balances of performance, reliability and cost.
Modern airframe history began in the United States when a 1903 wood biplane made by Orville and Wilbur Wright showed the potential of fixed-wing designs. Many early developments were spurred by military needs during ....etc

[:=Read Full Message Here=:]

Weber carburetors were originally produced in Italy by Edoardo Weber as part of a conversion kit for 1920s Fiats. Weber pioneered the use of twin barrel carburetors with two barrels (or venturi) of different sizes, the smaller one for low speed running and the larger one optimised for high speed use.

In the 1930s Weber began producing twin barrel carburetors for motor racing where two barrels of the same size were used. These were arranged so that each cylinder of the engine has its own carburetor barrel. These carburetors found use in Maser ....etc

[:=Read Full Message Here=:]

Introduction


The swashplate engine (also sometimes called axial engine or barrel engine) is a type of reciprocating engine that replaces the common crankshaft with a circular plate (the swashplate). Pistons press down on the plate in sequence, forcing it to nutate around its center. This motion can be simulated by placing a CD on a ball bearing at its centre and pressing down at progressive places around its circumference. The plate, also known as a wobble plate, is typically ....etc

[:=Read Full Message Here=:]

Great Depression



Economic history

The timing and severity of the Great Depression varied substantially across countries.
The Depression was particularly long and severe in the United States and Europe; it was milder
in Japan and much of Latin America. Perhaps not surprisingly, the worst depression ever
experienced stemmed from a multitude of causes. Declines in consumer demand, financial
panics, and misguided government policies caused economic output to fall in the United States.
The gold standard, ....etc

[:=Read Full Message Here=:]

PRACTICAL TRAINING At Z-LED Light


Presented by:
Anirudh Vyas
SCHOOL OF ELECTRONICS & COMMUNICATION ENGINEERING
JODHPUR ENGINEERING COLLEGE AND RESEARCH CENTRE JODHPUR (RAJ.)
Rajasthan Technical University, Kota.


Light-Emitting Diode
Light-emitting diode
Red, green and blue LEDs of the 5mm type
Type
Passive, optoelectronic
Working principle Electroluminescence
Invented Nick Holonyak Jr. (1962)
Electronic symbol
Pin configuration Anode and Cathode
A light-emitting diode (LED) is an elect ....etc

[:=Read Full Message Here=:]

Please send me report on turbocharger. Please fast ....etc

[:=Read Full Message Here=:]

presented by:
K.L.PANDEY


WELDING
Welding is a fabricationprocess that joins materials, usually metals or thermoplastics, by causing coalescence. This is often done by melting the workpieces and adding a filler material to form a pool of molten material (the weld pool) that cools to become a strong joint, with pressure sometimes used in conjunction with heat, or by itself, to produce the weld. This is in contrast with soldering and brazing, which involve melting a lower-melting-point material between the work ....etc

[:=Read Full Message Here=:]

see the page link
http://en.wikipediawiki/Intelligent_Transportation_Systems
ieeeitss
civil.iitb.ac~b5kushal/EE%20002%20Project--final.ppt
its.dot.gov/
Interest in ITS comes from the problems caused by traffic congestion and a synergy of new information technology for simulation, real-time control, and communications networks. Traffic congestion has been increasing worldwide as a result of increased motorization, urbanization, population growth, and changes in population density. Congestion reduces efficiency of transportation infrastruc ....etc

[:=Read Full Message Here=:]