I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I ne ....etc

[:=Read Full Message Here=:]

Please send ppt about it and as well as report for same. ....etc

[:=Read Full Message Here=:]

Kindly requesting u to give a brief seminar report on the topic reservoir induced seismicity

....etc

[:=Read Full Message Here=:]

I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I need reservoir sampling.I ne ....etc

[:=Read Full Message Here=:]

Presentatied by:
R.Bharathi Murugan




Storage capacity of reservoir:

The available Storage capacity depends upon the size and the height of dam.
Engineering surveys are usually conducted for preliminary estimation of the capacity.
Survey of Indian map can be used .Scale 1cm=500m(RF=1/50000)and1cm=2500
(RF=1/250000)

For accurate determination of the capacity a topographic survey of the area is usually conducted and a contour map of the area is prepared.
A Contour plan of the area is pre ....etc

[:=Read Full Message Here=:]

Study Of Ground Water Qualities in and around Byramangala Reservoir



INTRODUCTION

Byramangala is a scenic village in Bidadi taluk of Ramanagaram District in Karnataka, about 24 miles away from Bangalore.
The village with its panoramic landscape and lush greenery entices the visitors. This charming hamlet is very famous for a lake called Byramangala Tank which shelters a large number of aquatic birds including migratory and resident birds.
The nearest areas of attraction include an impressive dome at the ....etc

[:=Read Full Message Here=:]

DESIGN AND FABRICATION OF PULSE TUBE REFRIGERATION SYSTEM

ABSTRACT
Cooling effect at one end of a hollow tube with a pulsating pressure in the inside gas, was first observed by Gifford and Longsworth in early sixties. This marks the inception of one of the most promising cryogenic refrigerators known as 'pulse tube refrigerator' (PTR). Cryogenics is the science of low temperature. Cryogenics refers to the entire phenomenon occurring below -150°C or 123K. Cryogenic engineering involves the design and development of ....etc

[:=Read Full Message Here=:]

ABSTRACT


Enhanced Oil Recovery is a generic term for techniques for increasing the amount of crude oil that can be extracted from an oil field. Using EOR, 30-60 %, or more, of the reservoir's original oil can be extracted compared with 20-40% using primary and secondary recovery. Its purpose is not only to restore formation pressure, but also to improve oil displacement or fluid flow in the reservoir.
Enhanced oil recovery is achieved by gas injection, chemical injection, microbial injection, or thermal ....etc

[:=Read Full Message Here=:]

SYSTEM DESIGN & DEVOLOPEMENT IN CALCULATION OF RESPONSE TIME FOR AIR BRAKE SYSTEM
INTRODUCTION
COMPONENTS OF AN AIR BRAKE SYSTEM:
Air brake system consists of the following components:
Compressor:
The compressor generates the compressed air for the whole system.
Reservoir:
The compressed air from the compressor is stored in the reservoir.
Unloader Valve:
This maintains pressure in the reservoir at 8bar.When the pressure goes above 8 bar it immediately releases the pressurized air to bring the system to 8-bar press ....etc

[:=Read Full Message Here=:]

ABSTRACT
Hydraulic systems provide a means of remotely controlling a wide range of components by transmitting a force through a confined fluid.
Because hydraulics can transmit high forces rapidly and accurately along lightweight pipes of any size, shape and length, they are the prime source of power in aircraft systems such as flying controls, flaps, retractable undercarriages and wheel brakes.
Modern aircrafts include many different types of subsystems. These subsystems are very closely interlinked t ....etc

[:=Read Full Message Here=:]

Introduction to Engineering Seismology
Presented By:
Dr. G. Madhavi Latha
Dept. of Civil Engineering
Indian Institute of Science



Introduction:
Seismology is the branch of Geophysics concerned with the study and analysis of Earthquakes and the science of energy propagation through the Earth's crust.
Engineering Seismology is concerned with the solution of engineering problems connected with the Earthquakes. Seismology is extremely important because:
Study of earthquakes gives us important clu ....etc

[:=Read Full Message Here=:]

E-WASTE MANAGEMENT
SEMINAR REPORT
Submitted by
BINDU V.GOPAL
DEPARTMENT OF CIVIL ENGINEERING
COLLEGE OF ENGINEERING TRIVANDRUM


ABSTRACT


The electronic industry is the world’s largest and fastest growing manufacturing industry in the world. Discarded electronic and electrical equipment with all of their peripherals at the end of life is termed e-waste. The quantity of e-waste generated in developed countries equals 1% of total solidwaste on an average and is expected to grow to 2% by 2010 and i ....etc

[:=Read Full Message Here=:]

The cam has been an integral part of the IC engine from its invention. The cam controls the €œbreathing channels of the IC engines, that is, the valves through which the fuel air mixture (in SI engines) or air (in CI engines) is supplied and exhaust driven out The cam has been an integral part of the IC engine from its invention. The cam controls theœbreathing channelsof the IC engines, that is, the valves through which the fuel air mixture (in SI engines) or air (in CI engines) is supplied and exhaust dr ....etc

[:=Read Full Message Here=:]

A moving train contains energy, known as kinetic energy, which needs to be removed from the train in order to cause it to stop. The simplest way of doing this is to convert the energy into heat.

The conversion is usually done by applying a contact material to the rotating wheels or to discs attached to the axles. The material creates friction and converts the kinetic energy into heat. The wheels slow down and eventually the train stops. The material used for braking is normally in the form of a block or pad

The vast majority of the ....etc

[:=Read Full Message Here=:]