ROLLER FREE, MINIATURE, PERISTALTIC PUMP WITH RECIPROCATING ACTUATOR
Seminar Report
By
MANU.V.S
S7 MECHANICAL ENGINEERING
(PTDC)
DEPARTMENT OF MECHANICAL ENGINEERING
COLLEGE OF ENGINEERING
THIRUVANANTHAPURAM
2010


ABSTRACT
The conventional modes of pumping are centrifugal, reciprocating, gear pump, lobe pump, vane pump etc. But these types of pumping cannot be used in delicate areas such as medical field, labs, pumping different types of fluids etc. Bec ....etc

[:=Read Full Message Here=:]

POWER SUPPLY FOR ELECTRIC TRACTION DRIVES
ABSTRACT
Electric Traction
There is a wide variety of electric traction systems around the world, which have been built according to the type of railway, its location and the technology available at the time of the installation. Many installations seen today were first built up to 100 years ago, some when electric traction was barely out its diapers, so to speak, and this has had a great influence on what is seen today.
In the last 20 years there has been a gigantic acceleration i ....etc

[:=Read Full Message Here=:]

This article is presented by:
1) vikas dogra
2) VIKRAM KHULLAR
3) VISHAL PRASHER
4) avinav goel
5) sukhwinder singh
MECHNICAL 2snd YEAR
M.E.-4Y
Crankshaft
INTRODUCTION
The crankshaft, sometimes casually abbreviated to crank, is the part of an engine which translates reciprocating linear piston motion into rotation. To convert the reciprocating motion into rotation, the crankshaft has crank throws or crankpins, additional bearing surfaces w ....etc

[:=Read Full Message Here=:]

FAILURE ANALYSIS OF SHELL AND TUBE HEAT EXCHANGER
PROJECT REPORT
Submitted by
ALEX BABY ARUN M V JAIN RAJ .V VIJEESH VIJAYAN
ABSTRACT
Tar column recoiled E4509 in the phenol plant of HOCL found failed in service un like any other exchanger s in phenol manufacturing process .Each failure very high cost to HOCL in terms of production loss due to down time for maintence and due to the loss of therminol liquid to the process .the loss due to each failure found to be nearly RS 1.5 chore >the cost of tube bundle in SS-316 is ....etc

[:=Read Full Message Here=:]

Torque Ripple Minimization in a Switched
Reluctance Drive by Neuro-fuzzy
Compensation

Simple power electronic drive circuit and fault tolerance of converter are specific advantages of SRM drives, but excessive torque ripple has limited its use to special applications. A new method for shaping the motor currents so that the ripple can be reduced is presented by this paper. Here, a compensating signal is added to the output of a PI
controller. This i ....etc

[:=Read Full Message Here=:]

seminars project on speed control of dc motor using igbt ....etc

[:=Read Full Message Here=:]

CHAIN DRIVES IN LOW TORQUE DRIVES AND REDUCING PULSATIONS
INTRODUCTION TO DRIVES

Mechanical components used for power transmission.It may be belt, chain or gear depending on engine design parameters like - Distance between crankshaft and camshaft, engine maximum speed, engine-torque and engine construction cost.- Power transmission is done from one shaft to another shaft which may or may not rotate at same spe ....etc

[:=Read Full Message Here=:]

PRESENTED BY
R. RADHIKA
B. USHA RANI


ABSTRACT
Permanent magnet synchronous motor (PMSM) has been widely used in high performance drive applications for its advantages such as compactness, high efficiency, reliability and suitability to environment. Due to its high power density and smaller size, PMSM has evolved as the preferred solution for speed and position control drives on machine tools and robots. A Permanent Magnet Synchronous Motor (PMSM) is a motor that uses permanent magnets to produce the air g ....etc

[:=Read Full Message Here=:]

ABSTRACT
Milking machine is the machine, which is used to milk cattle. It revolutionized the dairy farm industry, as it is an efficient and time saving means of milking machine. The development of the milking machine has been by trial and error from a very early time. Its development is still continuing. This paper deals with the explanation of the parts involved in the milking machine.
This also involves the working of the milking machine and the certain advancement involved in it.
INTRODUCTION
....etc

[:=Read Full Message Here=:]

CHAIN DRIVES IN LOW TORQUE DRIVES AND REDUCING PULSATIONS
INTRODUCTION TO DRIVES

Mechanical components used for power transmission.It may be belt, chain or gear depending on engine design parameters like - Distance between crankshaft and camshaft, engine maximum speed, engine-torque and engine construction cost.- Power transmission is done from one shaft to another shaft which may or may not rotate at same spe ....etc

[:=Read Full Message Here=:]

types of gear box and how to reduce the noises in them ....etc

[:=Read Full Message Here=:]