PREPARED BY
MAK


1. INTRODUCTION
• The project is for manufacture of simple engineering spares and for undertaking job work on lathe for turning and welding requirements.
• 3. MANUFACTURING PROCESS
• The manufacturing process depends upon the type of job. Generally, the job includes raw material, cutting, drilling, turning & facing, milling & parting off, inspection and despatch. Diploma in Mechanical Engineering (DME) and ITI (Turner Trade) trained persons can establish these kind of units for ....etc

[:=Read Full Message Here=:]

062/2016
Maximum : 100 marks
Time : 1 hour and 15 minutes


1. Article 56 of Indian constitution declares :
(A) Election of the President.
(B) Manner of election of the president
(C ) Qualifications for election as president
(D) Term of office of president

2. Among the following which is not a sub clause of Article 19:
(A) Right to establish and maintain institutions for religious and charitable purposes
(B) Right to form associations
(C ) Right to assemble peaceably and without arms
(D) Freedom of speech and ....etc

[:=Read Full Message Here=:]

123/2016
1The Constituent Assembly met for the first time on 9th December in which year ?
A) 1947 (B) 1946 C) 1950 D) 1949

2'Objective Resolution' drafted and moved by Pandit Jawaharlal Nehru in the Constituent Assembly on
A) 13 December, 1946 (B) 30 January, 1946
C) 26 January, 1950 D) 3 December, 1950

3First Delimitation Commission was setup in India on
A) 1976 (B) 1955 C) 1951 D) 1960

4The Prime Minister’s Secretariat was renamed into Prime Minister’s Office at the time of
A) P. V. Narasimha Rao ((B) Ja ....etc

[:=Read Full Message Here=:]

Power electronics remains an emerging technology. Two important factors in power electronics system are the switching speed of the devices and the total power loss in the system. If the switching speed can be increased ,improvements may be possible i.e. current ripples in an electrical machine or physical size of passive components may be reduced. Increased switching speed may cause additional losses in a power electronics system and increase the system cooling requirement. A common problem is that high-frequency phenomena like proximity eff ....etc

[:=Read Full Message Here=:]

Relationship between education and culture
....etc

[:=Read Full Message Here=:]

general problem in engineering and technological. ....etc

[:=Read Full Message Here=:]

Construction engineering successful graduates will have a good understanding of all facets of construction systems and general contracting. A strong construction need for qualified construction engineering technologists which continues to provide opportunities for program graduates. Typical construction employers include construction firms, government agencies, construction material manufacturers and suppliers, property developers and consulting firms.
Typical construction career positions include.
A)estimator
B)project inter coordinator/man ....etc

[:=Read Full Message Here=:]

i request u to please allow me to download seminar topics on personality development. ....etc

[:=Read Full Message Here=:]

Power electronics remains an emerging technology. Two important factors in power electronics system are the switching speed of the devices and the total power loss in the system. If the switching speed can be increased ,improvements may be possible i.e. current ripples in an electrical machine or physical size of passive components may be reduced. Increased switching speed may cause additional losses in a power electronics system and increase the system cooling requirement. A common problem is that high-frequency phenomena like proximity eff ....etc

[:=Read Full Message Here=:]

85/2014
Maximum : 100 marks
Time : 1 hour and 15 minutes

1. V belt run in-------------------degree v-groove.
(A)60°
(B)55°
(C )29°
(D)40°

2. The -----------------is the operation of forming the edges of a component into roll by bending the sheet metal in order to strengthen the edges and to provide smoothness to its surface :
(A)Bending
(B)Curling
(C )Lancing
(D)Forming

The back gear system of a lathe is used to :
(A)Reduce the spindle speed
(B)Increase the spindle speed
(C )Only used in thread cut ....etc

[:=Read Full Message Here=:]