digrams regarding the topic ....etc

[:=Read Full Message Here=:]

Jet impingement heat transfer – Part I: Mean and root-mean-square heat transfer and velocity distributions
Abstract
Impinging jets provide a means of achieving high heat transfer coefficients both locally and on an area averaged basis. The currentwork forms the first stage of a two part investigation of heat transfer distributions from a heated flat surface subject to an impinging airjet for Reynolds numbers from 10,000 to 30,000 and non-dimensional surface to jet exit spacing, H/D, from 0.5 to 8. In the present paper,the rel ....etc

[:=Read Full Message Here=:]

Presented by:
A.JohnBritto
C.Kanaga Raj
P.Senna Kesavan
A.VinothHEAT TRANSFER PERFORMANCE IN 3D INDUCED FINNED HEAT PIPE

ABSTRACT
3D induced finned steel-water heat pipe is carried out in this project.

All the main parameters that can significantly influence the heat transfer performance of heat pipe ,such as working temperature, heat flux, inclination angle, working fluid fill ratio (defined by the evaporatio ....etc

[:=Read Full Message Here=:]

High Conductance Heat Transfer Using Solar Heat Pipe Collector

presented by :-
MR. SHIVAJI D. YADAO1, MR. PRMENDRA J BANSOD2
Dr. D.Y.Patil Institute of Engg. & Tech.,Pune University, Pune,
Dr. D.Y.Patil Institute of Engg. & Tech.,Pune University, Pune,

abstract
In recent years it has become increasingly important to develop methods for efficient transport of thermal energy from one location to another. Moreover the advent of the space age has stimulated research for heat transfer devices which are ....etc

[:=Read Full Message Here=:]

ABSTRACT
Fuel in any engine is burnt with air. Air is a mixture of gases and it contains approximately 78% nitrogen and 21% oxygen. Some of the oxygen is used to burn the fuel during the combustion process and the rest is supposed to just pass through unreacted. But when the peak temperatures are high enough for long periods of time, the nitrogen and oxygen combine to form a class of compounds called nitrogen oxides, collectively referred to as NOx. These compounds are one of the chie ....etc

[:=Read Full Message Here=:]

K. Wojciechowski, J. Merkisz, P. Fuć
, P. Lijewski, M.Schmidt


Abstract
Automotive engines reject a considerable amount of energy to the ambience through the exhaust gas. Significant reduction of engine fuel consumption could be attained by recovering of exhaust heat by using thermoelectric generators. One of the most important issues is to develop an efficient heat exchanger which provides optimal recovery of heat from exhaust gases. The work presents a design and perform ....etc

[:=Read Full Message Here=:]

IMPROVEMENT OF THERMAL EFFICIENCY BY RECOVERY OF HEAT FROM IC ENGINE EXHAUST
(THERMAL SCIENCES)
CONTENTS:
1. ABSTRACT
2. INTRODUCTION
3. PRINCIPLE OF HEAT RECOVERY FROM IC ENGINE
4. NECESSITY OF THERMAL STORAGE SYSTEM
5. LATENT HEAT THERMAL STORAGE SYSTEM
6. EXPERIMENTAL SETUP
7. RESULTS AND DISSCUSSIONS
8. PERFORMANCE CHARACTERISTICS STUDY
9. CONCLUSION
IMPROVEMENT OF THERMAL EFFICIENCY BY RECOVERY OF HEAT FROM IC ENGINE EXHAUST
ABSTRACT
The steady increased consumption of fuel and power over the years have ....etc

[:=Read Full Message Here=:]

DjtmtjapjmTjdgumjpxjgugumjpupvdmtpgmtpglngjmtpgajptnjgtwjpuwdjgpm ....etc

[:=Read Full Message Here=:]

send me information immediately...........
my email id: [email protected]
....etc

[:=Read Full Message Here=:]

Faurecia Exhaust Systems AB develops and manufactures exhaust manifolds for the car industry. In the developing process the FE-models are one of the main tools and they are becoming more and more important in the automotive development. In the tough competition between the manufacturers, the demands for fast development require good FE-models both from the manufacturers and their subcontractors.The main goal of this thesis is to update an existing FE-model of a close coupled exhaust manifold and look at the catalyst to investigate the behavior ....etc

[:=Read Full Message Here=:]