HEATSINK CALCULATION AND EXAMPLES
In many cases, GS-Rx and GSxTy-z modules don’t require any additional cooling methods because the dimensions and the shape of the metal boxes were studied to offer the minimum possible thermal resistance case to ambient for a given module. It should be remembered, that GS-R and GS-T modules are power devices i.e. products that deliver power and dissipate power and, depending on ambient temperature, an additional heat-sink or forced ventilation or both may be required to ....etc

[:=Read Full Message Here=:]

dfd examples of marksheet generation system ....etc

[:=Read Full Message Here=:]

Explanatory Examples on Indian Seismic Code IS 1893


Problem Statement:
Consider a four-storey reinforced concrete office building shown in Fig. 1.1. The building is located in
Shillong (seismic zone V). The soil conditions are medium stiff and the entire building is supported on a raft
foundation. The R. C. frames are infilled with brick-masonry. The lumped weight due to dead loads is 12
kN/m2 on floors and 10 kN/m2 on the roof. The floors are to cater for ....etc

[:=Read Full Message Here=:]

Training Session on Energy Equipment



Introduction

What’s a Cogeneration/CHP System?

.Generation of multiple forms of energy in one system: heat and power

.Defined by its “prime movers”
-Reciprocating engines
-Combustion or gas turbines,
-Steam turbines
-Microturbines
-Fuel cells

Benefits of Cogeneration

.Increased efficiency of energy conversion and use
.Lower emissions, especially CO2
.Ability t ....etc

[:=Read Full Message Here=:]

Abstract—
In this paper, we address the problem of nonlinear
sensor dynamic compensation that will be performed on board
wireless sensor network nodes. To this aim, we design suitable
reduced-complexity learning-from-example algorithms and implement
them on resource-constrained devices, namely, 8-bit
microcontrollers. The proposed approach is validated with simulations
on different examples of nonlinear sensor models.
Index Terms—Dynamic compensation, low power, microcontroller
implementation, reduced-set methods, support v ....etc

[:=Read Full Message Here=:]

EXAMPLES ON LINEARIZATION



Consider the electromagnetic suspension system shown in the figure. An electromagnet is
located at the upper part of the experimental system. Utilizing the electromagnetic force f,
we desire to suspend the iron ball. Note that this simple electromagnetic suspension
system is essentially unworkable. Hence feedback control is indispensable. As a gap
sensor, a standard induction probe of eddy current type is placed below the ball.


[b ....etc

[:=Read Full Message Here=:]

Flow Chart Examples


Benefits of Using Flowcharts
• Promotes understanding of a process
• Identifies problem areas and opportunities for process
improvement
• Provides a way of training employees
• Depicts customer-supplier relationships



If you read through ISO 9001:2000, you will find 6 places where Documented Procedures
are specifically stated to be a requirement. Some folks have been saying how nice it is that
the documentation requirem ....etc

[:=Read Full Message Here=:]

1. Auto turn off water pump with four different time slots using PSOC Mixed Signal Array
2. Proximity Sensor based intelligent Security system using PSoC mixed signal array
3. RFID access with PSoC mixed signal array
4. RF based Wireless Industrial Device control using PSOC Mixed Signal Array
5. Light intensity based Street light automation using PSOC Mixed Signal Array
6. Implementing loopback SPI protocol using PSoC mixed signal array
7. Capsense based Industrial appliances control system with PSoC mixed signal array
8. Accelerometer ....etc

[:=Read Full Message Here=:]

difference between tcp session hijacking and udp session hijacking ....etc

[:=Read Full Message Here=:]

Verilog Examples


Combinational Logic Structures

Continuous assignment statements are a very useful and compact language structure for specifying small
collections of gates. The following examples are intended to go beyond those provided in the text and
illustrate concepts that sometimes are found to be difficult.

Multiple-input Multiplexors

Multiplexors requiring more than two inputs can also be specified using procedural code, usually by using a
case or casex satement. The 8:1 multiplexor d ....etc

[:=Read Full Message Here=:]