xperimental results on ?ber micro-buckling of continuous glass-?ber reinforced hollow-cored recycled plastic extrusions under creep tests are introduced. The full size specimens with dimensions in 2:5 Â 3:5 Â 42 in:3 were submerged in warm water at a temperature of 125 °F when they were under a four-point bending creep test. The results show that the micro-buckling of the embedded glass-?ber roving occurs along 90% the length of the specimen on the upper inner surface (compressive side) and mainly during the time bet ....etc

[:=Read Full Message Here=:]

wanted a topic for seminar on AMS ( Advanced Manufacturing Systems) ....etc

[:=Read Full Message Here=:]

130/2015
Maximum : 100 marks
Time : 1 hour and 15 minutes

1. Stainless steel is an alloy of which among the following?
(A)chromium, nickel and iron
(B)manganese, copper andiron
(C )copper, carbon and iron
(D)copper, tin and zinc

2.What is determined by conducting an abrasion test?
(A)aggregate crushing value
(B)toughness
(C )hardness
(D)soundness

3.On which of the following, the support for flat slab is provide?
(A)beams built monolithic ally abovewalls
(B)columns built monolithicallywith slab
(C )be ....etc

[:=Read Full Message Here=:]

If You Want More Information Please reply Below

1. A comprehensive water management plan

2. A New Method to Determine Plastic Limit of Soil

3. A Relation between COD and BOD for the textile,

4. Advanced Earthquake Resistant Techniques

5. Advanced Pavement Design

6. Advanced Technology in Sewage Treatment & Nutrient Removal

7. advancement in geotechnical engg. with geo

8. Air pollution & its control

9. Alum Recovery By Acidulation of Aluminum Hydroxide Sludge

10. Alum With ....etc

[:=Read Full Message Here=:]

BLOCK SHEAR FAILURE IN TENSION MEMBERS
ABSTRACT
Block shear is a limit state that should be accounted for during the design of steel tension members. This failure mechanism combines a tensile failure on one plane and a shear failure on a perpendicular plane. It is important for a design equation not only to predict the capacity reliably, but also to predict accurately the failure mode.
In this study, we begin with an overview of tension members, their behaviour and design strength which is affected by yielding, fracture or ....etc

[:=Read Full Message Here=:]

Analysis of soil classification using normalized piezocone parameters
Analysis of soil classification using normalized piezocone parameters

Introduction
The number of variables which influence cone tip resistance, penetration pore pressures, and CPT sleeve friction typically exceed the range of variables covered by databases of sites used for calibration of correlations for soil classification charts. Therefore, it is important to understand the mechanisms which influence piezocone parameters during the development of design recommendati ....etc

[:=Read Full Message Here=:]

1. A comprehensive water management plan

2. A New Method to Determine Plastic Limit of Soil

3. A Relation between COD and BOD for the textile,

4. Advanced Earthquake Resistant Techniques

5. Advanced Pavement Design

6. Advanced Technology in Sewage Treatment & Nutrient Removal

7. advancement in geotechnical engg. with geo

8. Air pollution & its control

9. Alum Recovery By Acidulation of Aluminum Hydroxide Slud ....etc

[:=Read Full Message Here=:]

ABSTRACT:
A good automobile shop must have equipment to undertake all types of fault finding and servicing jobs. The tools and equipment which are must in the auto shop are namely screw drivers, spanners, hydraulic lift, wheel balancing equipment etc. One of the important equipments is the hydraulic lift which can be a 2-post, 4-post, 6-post which is used to lift the vehicles to a comfortable height in order to work under it. For the same purpose the latest equipment used is the Screw Auto Lift.
Much of the fatigue damage in th ....etc

[:=Read Full Message Here=:]

Breakage (Soil) Mechanics

Introduction
Critical state soil mechanics (CSSM) was originally developed for clays. For this application CSSM continues to provide the most elegant mathematical theory for capturing the physics of the material. In its simplicity, only five parameters are needed to describe a broad range of critical effects. However, when CSSM is adapted to model sand-agglomerates, models can no longer be accurately defined using five parameters. The CSSM theory requires fitting the slope of the isotropic-hardening compression ....etc

[:=Read Full Message Here=:]

ABSTRACT:
A good automobile shop must have equipment to undertake all types of fault finding and servicing jobs. The tools and equipment which are must in the auto shop are namely screw drivers, spanners, hydraulic lift, wheel balancing equipment etc. One of the important equipments is the hydraulic lift which can be a 2-post, 4-post, 6-post which is used to lift the vehicles to a comfortable height in order to work under it. For the same purpose the latest equipment used is the Screw Auto Lift.
Much of the fatigue damage in th ....etc

[:=Read Full Message Here=:]

053/2016
Maximum : 100 marks
Time : 1 hour and 15 minutes

1.A steel bar 10 mm x 10 mm cross section is subjected to an axial 

tensile load of 20 kN. If the length of bar is 1 m and E = 200 

GPa, then elongation of the bar is ?
(A)1 mm (B)0.5 mm
(C )0.75 mm (D)1.5 mm

2.The modulus of rigidity and poisson’s ratio of a material are 

80GPa and 0.3 respectively, Its youngs modulus will be ?
(A)160 GPa (B)208 GPa
(C )120 GPa (D)104 GPa

3.The equivalent torque on a shaft, when it is subjected to 

b ....etc

[:=Read Full Message Here=:]

I'm dying to have this tutorial. total beginner ...

thanks a lot. ....etc

[:=Read Full Message Here=:]