1. Project Objective

The advent of new high-speed technology and the growing computer capacity provided realistic opportunity for new robot controls and realization of new methods of control theory. This technical improvement together with the need for high performance robots created faster, more accurate and more intelligent robots using new robots control devices, new drives and advanced control algorithms.
This project describes a new economical solution of robot control systems. The presented robot control system can be used for differe ....etc

[:=Read Full Message Here=:]

i need information on this particular topic ....etc

[:=Read Full Message Here=:]

Abstract

Automatic Street Light Control System is a simple yet powerful concept, which uses transistor as a switch. By using this system manual works are 100% removed. It automatically switches ON lights when the sunlight goes below the visible region of our eyes. This is done by a sensor called Light Dependant Resistor (LDR) which senses the light actually like our eyes. It automatically switches OFF lights whenever the sunlight comes, visible to our eyes.

By using this system energy consumption is also re ....etc

[:=Read Full Message Here=:]

AUTOMATIC STREET LIGHT CONTROL USING LDR
Abstract:
This project aims at designing and executing the advanced development in embedded systems for energy saving of street lights with light depending resistor. Nowadays, human has become too busy and he is unable to find time even to switch the lights wherever not necessary. This can be seen more effectively in the case of street lights. The present system is like, the street lights will be switched on in the evening before the sun sets and they are sw ....etc

[:=Read Full Message Here=:]

ABSTRACT
This project deals with “Development of an Embedded system for Automatic street light controlling with Sun Tracking” using micro controller AT89C52 and Light sensor named as light dependent resistor (LDR).
In our daily life we are observing street lights still on in day time also. In this type of conditions the electricity (power) is wasted. This project deals with how to avoid this condition using embedded system.
The project presented h ....etc

[:=Read Full Message Here=:]

The main objective of this project is to reduce the power consumption in the streets. according to the existing system, power consumption is more due to the irregular functionalities of the street lights. By using our proposed system, we can control the consumption of power. initially, the light will be in dim condition, whenever the vehicle crosses the sensor(controller),light starts to increase .brightness of the light is depends on the number of vehicles which crosses the sensor. if one vehicle crosses the sensor, the light will be in minimu ....etc

[:=Read Full Message Here=:]

Submitted by
JITENDRA SINGH
VIKRAM PRATAP SINGH
SHAILENDRA KUMAR


INTRODUCTION
In this project we show that how we generate a valuable voltage with the help of moving traffic on the road. When battery is fully charged then we use battery for our project.
We install one photoelectric effect in the project. Street light is to be switch on automatically in the night and lights are automatically off in the day night.
In this project we switch on the street light in night in half mode. Half mode means all the ....etc

[:=Read Full Message Here=:]

AUTOMATIC STREET LIGHT OPERATION THROUGH SMS


M.Mohana Anjaneyulu - 05F01A0438
G.V.Mallikarjuna - 05F01A04B0
A.Srikanth - 05F01A0486
E.Suresh - 05F01A0493

Electronics & Communication Engineering
St.ANN’S COLLEGE OF ENGINEERING & TECHNOLOGY

ABSTRACT

The automatic street light controller is basically operated according with the light intensity. The simple concept about this operation is that, whenever there is less intensity ....etc

[:=Read Full Message Here=:]

hi friends,
am a 3rd year engg student.i would like to do a project on the above topic.i need the information on constructional details of the the controller and the parts required.i would like you to send the details.i want to design the controller.so please send required information ....etc

[:=Read Full Message Here=:]

ABSTRACT

Aim of this project is to control the street light using LDR. LDR(light dependent resistance) . When the light falling occurs means resistance value will be change. There is no light then the resistance value is change. From this resistance change the voltage variation can be obtained this value is given to ADC of PIC. PIC is stand for peripheral interface controller.

ADC is inbuilt in PIC. The function of the ADC is to convert the analog signal to digital signal. From this digital signal the light in the environment can b ....etc

[:=Read Full Message Here=:]