ABSTRACT
Here is a microcontroller based wireless equipment controller that can switch on or off upto four devices at a desired time interval set by the user in the transmitter. The devices can be controlled remotely from a distance upto 30 metres from the transmitter. In the transmitter, an LCD module is used to show the device numbers and preset control time for the devices (00 to 99 seconds). The 8-bit AT89C51 microcontroller is the main controlling part of the transmitter section. It is connected to the LCD modu ....etc

[:=Read Full Message Here=:]

I AM SEARCHING FOR CIRCUIT DIAGRAM OF MICROCONTROLLER AT89C51 BASED AUTO SPEED LIMITER WITH AUTO BREAKING ....etc

[:=Read Full Message Here=:]

Submitted By
ACHARYA MIRAJ SHAILESHBHAI


INTRODUCTION
The declining prices of the LCDs. The ability to display number, characters and graphics. This is in contrast with LEDs, which are limited to numbers and few characters. Incorporation of a refreshing controller in to LCD, thereby relieving the CPU to keep displaying the data. Ease of programming for the characters and graphics.
Block Diagram
Block Description:
In this project there are three main blocks
1. Power supply section
2. Controll ....etc

[:=Read Full Message Here=:]

POWER SUPPLY
The input to the circuit is applied from the regulated power supply. The a.c. input i.e., 230V from the mains supply is step down by the transformer to 5V and is fed to a rectifier. The output obtained from the rectifier is a pulsating d.c voltage. So in order to get a pure d.c voltage, the output voltage from the rectifier is fed to a filter to remove any a.c components present even after rectification. Now, this voltage is given to a voltage regulator to obtain a pure constant dc voltage
Transformer ....etc

[:=Read Full Message Here=:]

PHASE-ANGLE CONTROL OF SCR USING AT89C51
Silicon-controlled rectifiers (SCR) are solidstate semiconductor devices that are usually used in power switching circuits. SCR controls the output signal by switching it ‘on’ or ‘off’, thereby controlling the power to the load in context. The two primary modes of SCR control are phase-angle fired-where a partial waveform is passed to regulate the power.
In the phase-angle controller, the firing pulse is delayed to turn on the SCR in middle of every half cycle. This ....etc

[:=Read Full Message Here=:]

1. INTRODUCTION
1.1 Context
This project explains about a simple low cost circuit which can be mainly used in large scale industries to detect the high temperature and take immediate measures. This circuit is used to sense the temperature at a place. It indicates the temperature on the 7 Segment Display with the help of microcontroller. This circuit makes use of SL100 which is a 3 pin centigrade temperature sensor IC. It directly senses the temperature and sends the data to the controller.
The complete project is ....etc

[:=Read Full Message Here=:]

MICROCONTROLLER AT89C51 BASED AUTO SPEED LIMITER WITH AUTO BREAKING ....etc

[:=Read Full Message Here=:]

DIGITAL AUDIO PROCESSOR USING AT89C51
1. BACKGROUND
This report presents an infrared (IR) remote-controlled digital audio processor.
It is based on a microcontroller and can be used with any NEC-compatible full function
IR remote-control. This audio processor has enhanced features and can be easily customized to meet individual requirements as it is programmable.
Its main features are:
1. Full remote control using any NEC-compatible IR remote control handset.
2. Provision for four stereo input chann ....etc

[:=Read Full Message Here=:]

Aim -To make a tutorial on AT89C51 development kit
Technical details –
Features
• Compatible with MCS-51™ Products
• 4K Bytes of In-System Reprogrammable Flash Memory
– Endurance: 1,000 Write/Erase Cycles
• Fully Static Operation: 0 Hz to 24 MHz
• Three-Level Program Memory Lock
• 128 x 8-Bit Internal RAM
• 32 Programmable I/O Lines
• Two 16-Bit Timer/Counters
• Six Interrupt Sources
• Programmable Serial Channel
• Low Power Idle and Power Down Modes
Description
The AT89 ....etc

[:=Read Full Message Here=:]

Please can anyone assist me with the write up of speed control of stepper motor using AT89c51 ....etc

[:=Read Full Message Here=:]