I am doing my M.tech in power electronics division.This is karthik....
I want designing aspects of buck boost matrix converter.Currently I am simulating the circuit.hardware design calculations of buck boost matrix converter is required.
Designing aspects means calculation of component values.... ....etc

[:=Read Full Message Here=:]

Analysis of Conduction and Switching Losses of A Matrix-Z-Source Converter for Automotive ISA 42 V System
ABSTRACT
The model of the conduction and switching loss for a
recently proposed matrix z-source converter (MZC) was
analytically established in this paper. The model offered the
basis for the thermal design for the converter.
I. INTRODUCTION
Voltage source inverters (VSI) have been used widely for
a long time in applications where bi-directionally converting
AC power into DC power is required. However such
co ....etc

[:=Read Full Message Here=:]

ABSTRACT
This paper proposes a shunt active filter to minimize the power quality impact instead of using the conventional fixed Filters of the matrix converters. Matrix converters inject significant harmonics and nonstandard frequency components into power systems. The proposed approach eliminates the total line current harmonics efficiently. By minimizing the Total Harmonic distortion the harmonic pollution in the power system will be reduced, and the power quality will be increased. The proposed approach has been tested and validate ....etc

[:=Read Full Message Here=:]

Abstruct-
Analysis, design, and implementation of the space vector modulated three-phase to three-phase matrix converter with input power factor correction are presented. The majority of published research results on the matrix converter control is given an overview, and the one, which employs sheous output-voltage and input-current space vector modulation, is systematically reviewed. The modulation algorithm is theoretically derived from the desired average transfer functions, using the indirect transfer function approach. ....etc

[:=Read Full Message Here=:]

hii, i want more information about the Optimal Intelligent Controller for Matrix Converter Induction Motor Drive System
thank you ....etc

[:=Read Full Message Here=:]

1. Analysis of Different Schemes of Matrix Converter with Maximum Voltage Conversion Ratio
2. Single-Phase Z-Source Buck-Boost Matrix Converter
3. Single-Phase Matrix Converter Operating as Buck and Boost Rectifier
4. Analysis and implementation of Matrix Converter
....etc

[:=Read Full Message Here=:]

ABSTRACT

The rectifier and inverter are used in vector control of induction motor. The most shortcomings are that exist a big capacitor and energy pass only from power sources to load. This paper details a novel matrix converter-indirect matrix converter. It is used in vector controlling research of induction motor and displaced for conventional inverter to supply power for induction motor. Because switches are bidirectional in the rectifier, it can realize bidirectional pass of the energy and decrease pollution of harmonic wave. Meanwhile ....etc

[:=Read Full Message Here=:]

Abstract
The main concept of unified power flow controller(UPFC) is based on back to back connection of two inverters witha common capacitor dc link. This capacitor brings about severaldisadvantages such as affecting the reliability of UPFC. Thispaper proposes a new topology for UPFC based on matrixconverter. This configuration is combination of nine 4-quadrantswitches and not any storage element. Main advantages ofproposed topology are reduction of number of switches, low costand size of UPFC. This operation of UPFC is tested andsimul ....etc

[:=Read Full Message Here=:]

Abstract –
The matrix converter is superior to the P W inverter drives because of its regeneration ability and sinusoidal input current. Therefore, it meets the stringent energy-efficiency and power quality requirements of the new century. This paper describes the basic operating principles and control method of the matrix converted; and reports the detailed experimental operating characteristics of an I1 kVA matrix converter drive over its full operating range. Through the experimental operating characteristics ....etc

[:=Read Full Message Here=:]

DIRECT TORQUE CONTROL FOR MATRIX CONVERTER-FED THREE PHASE INDUCTION MOTOR WITH HYBRID PSO
ABSTRACT
Direct Torque Control (DTC) for Induction Motors using Matrix Converters is a high performance motor
control scheme with fast torque and flux responses. This paper presents a new control scheme based on
hybrid particle swarm optimization (HPSO). The main advantages of the matrix converter are combines
with those of the DTC technique, generating the required voltage vectors under 0.9 input power factor
operations. The results ....etc

[:=Read Full Message Here=:]