10 Gigabit Ethernet

From its origin more than 25 years ago, Ethernet has evolved to meet the increasing demands of packet-switched networks. Due to its proven low implementation cost, its known reliability, and relative simplicity of installation and maintenance, its popularity has grown to the point that today nearly all traffic on the Internet originates or ends with an Ethernet connection. Further, as the demand for ever-faster network speeds has grown, Ethernet has been adapted to handle these ....etc

[:=Read Full Message Here=:]

Please help me..................................!!!!!!!!!!!!!
I want a seminar report of atleast 30 pages on GI-FI or gigabit wireless.............. and i also want slides

my id is [email protected] ....etc

[:=Read Full Message Here=:]

Gigabit PickPacket: A Network Monitoring Tool for Gigabit Networks


The extensive use of computers and networks for exchange of information has also had ramifications on the growth and spread of crime through their use. Law enforcement agencies need to keep up with the emerging trends in these areas for crime detection and prevention. Among the several needs of such agencies are the need to monitor, detect and analyze undesirable network traffic. However, the monitoring, detecting, and analysis of this traffic may be against the goal ....etc

[:=Read Full Message Here=:]

need report on this project,very urgently ....etc

[:=Read Full Message Here=:]

Abstract
A Gigabit Ethernet passive optical network (GE-PON)
The GE-PON includes an optical line terminal (OLT), a plurality of optical couplers, and a plurality of optical network units (ONUs). The OLT sets up an active page link and a standby page link in response to a registration request message received over an optical cable. Each of the ONUs is doubly connected with the OLT via the optical cable and is adapted to transmit the registration request message to the OLT, form the active page link with the OLT via the optical cable if it re ....etc

[:=Read Full Message Here=:]

Since its inception at Xerox Corporation in the early 1970s, Ethernet has been the dominant networking protocol. Of all current networking protocols, Ethernet has, by far, the highest number of installed ports and provides the greatest cost performance relative to Token Ring, Fiber Distributed Data Interface (FDDI), and ATM for desktop connectivity. Fast Ethernet, which increased Ethernet speed from 10 to 100 megabits per second (Mbps), provided a simple, cost-effective option for backbone and server connectivity.

In 1995 ,the Fast Ethernet ....etc

[:=Read Full Message Here=:]

i need ppt presentation on this thread ....etc

[:=Read Full Message Here=:]

Presented By
Mukesh kumar


Abstract
Computer Networks have greatly evolved in the last decade. These changes included improvement in network speed, latency and also related issues in physical media and computer architecture. All this was motivated by the requirements for new services and the introduction of new technologies. This change accumulated until they reached a point in which the nature of networks itself was transformed. The basic concerns and design principles will suffer a metamorphosis that will af ....etc

[:=Read Full Message Here=:]

10 GIGABIT ETHERNET
A SEMINAR REPORT
Submitted by
VIKASH MISHRA
in partial fulfillment of requirement of the Degree
of
Bachelor of Technology (B.Tech)
in
COMPUTER SCIENCE AND ENGINEERING
SCHOOL OF ENGINEERING
COCHIN UNIVERSITY OF SCIENCE AND TECHNOLOGY
KOCHI- 682022
AUGUST 2008Page 2

DIVISION OF COMPUTER SCIENCE AND ENGINEERING
SCHOOL OF ENGINEERING
COCHIN UNIVERSITY OF SCIENCE AND TECHNOLOGY
KOCHI-682022
Certificate
Certified that this is a bonafide record of the seminar entitled
10 GIGABIT ETHERNET
Presented by the foll ....etc

[:=Read Full Message Here=:]

Design of an Ethernet-based Robotic Motion Controller


Introduction

The purpose of this report is to document the design process used to create an Ethernet-based
robotic motion controller. This core of this project will be two Atmel ATMega128
microcontrollers, linked together using dual-port RAM. One microcontroller will strictly handle
Ethernet communication, while a second microcontroller will actually interface with the motor
control circuitry and sen ....etc

[:=Read Full Message Here=:]