Remote Procedure Call
RPC Timeline
RCP Components
• Protocol Stack
– BLAST: fragments and reassembles large messages
– CHAN: synchronizes request and reply messages
– SELECT: dispatches request to the correct process
• Stubs Bulk Transfer (BLAST)
• Unlike AAL and IP, tries to recover from lost fragments
• Strategy
– selective retransmission
– aka partial acknowledgements
BLAST Details
• Sender:
– after sending all fragments, set timer DONE
– if receive SRR, send missing..............etc

[:=Read Full Message Here=:]

i need embedded systems interview questions and answers for interview. Please help friends..............etc

[:=Read Full Message Here=:]

Generic Framing Procedure (GFP) is defined by ITU-T G.7041. This allows mapping of variable length, higher-layer client signals over a transport network like SDH/SONET. The client signals can be protocol data unit (PDU) oriented (like IP/PPP or Ethernet Media access control ) or can be block-code oriented (like fiber channel).
There are two modes of GFP, viz., GFP-F and GFP-T. GFP-F maps each client frame into a single GFP frame. GFP-T, on the other hand, allows mapping of multiple 8B/10B client data frames into an efficient 64B/65B block..............etc

[:=Read Full Message Here=:]

Generic Framing Procedure (GFP) is defined by ITU-T G.7041. This allows mapping of variable length, higher-layer client signals over a transport network like SDH/SONET. The client signals can be protocol data unit (PDU) oriented (like IP/PPP or Ethernet Media access control ) or can be block-code oriented (like fiber channel).
There are two modes of GFP, viz., GFP-F and GFP-T. GFP-F maps each client frame into a single GFP frame. GFP-T, on the other hand, allows mapping of multiple 8B/10B client data frames into an efficient 64B/65B block..............etc

[:=Read Full Message Here=:]

Generic Framing Procedure

Generic Framing Procedure (GFP) is defined by ITU-T G.7041. This allows mapping of variable length, higher-layer client signals over a transport network like SDH/SONET. The client signals can be protocol data unit (PDU) oriented (like IP/PPP or Ethernet Media access control ) or can be block-code oriented (like fiber channel).There are two modes of GFP, viz., GFP-F and GFP-T. GFP-F maps each client frame into a single GFP frame. GFP-T, on the other hand, allows mappin..............etc

[:=Read Full Message Here=:]

help me for my asp project on online Admission procedure...............etc

[:=Read Full Message Here=:]

PRESENTED BY;
NITHYA. D


A STUDY ON EFFECTIVENESS OF GRIEVANCE REDRESSAL PROCEDURE WITH RESPECT TO RANE ENGINE VALVE LTD, PLANT3, PONNERI, RANE GROUP”
ABSTRACT
This project entitled “A Study on Effectiveness of Grievance Redressal Procedure with
respect to Rane Engine Valve LTD, Plant 3, Ponneri, Rane Group” is done to understand the
effectiveness of the grievance handling procedure followed by Rane Engine Valve LTD to
resolve employees grievance.
The primary objective of this study is to find..............etc

[:=Read Full Message Here=:]

The study of micro cracks in concrete is very important to understand its behavior under loading and to improve this material. The direct observation in a scanning microscope is not a suitable method because the concrete is subject to drying shrinkage. Another indirect and non destructive method of observation by SEM is proposed. With this method using a single replica the micro cracks of concrete can be observed better than 0.5 µm...............etc

[:=Read Full Message Here=:]

Power & Procedure for conducting Inquiries Under the Protection of Human Rights Act, 1993

Presented By
Naresh Kumar Azad
LL.M ( 3rd Trimester






Powers Relating to Inquiries

Have all the powers of Civil Court
Summoning and & enforcing the
attendance of witnesses & Examine them on oath;

Discovery & production of any document;

Receiving evidence on affidavits;

Issuing commissions for the examination witnesses or documents

..............etc

[:=Read Full Message Here=:]

KEIL SOFTWARE PROGRAMING PROCEDURE
How to write Embedded C Program in Keil Software.
Procedure Steps
Step-1:
Install Keil MicroVision-2 in your PC, Then after Click on that “Keil UVision-2” icon. After opening the window go to toolbar and select Project Tab then close previous project.
Step-2:
Next select New Project from Project Tab.
Step-3:
Then it will open “Create New Project” window. Select the path where you want to save project and edit project name.
Step-..............etc

[:=Read Full Message Here=:]