02-02-2010, 10:48 PM
[attachment=1697]
SELF LUBRICATING TYRES
ABSTRACT
SELF INFLATING TYRES
Development in automobile engineering is the sign of rise in civilization. Along with comfort and facitilities it has revolutionized the living habits of the people to a great extent. Large scale use of power window, steering system, anti locking brakes, electronic control of car, self inflating tyres etc, will not only reduce the operating cost but also add standards in comfort. Self-inflating tyres are one of them.
Tyres are not carrying the weight of cars and trucks but it is the air inside the tyres which carries it. Run flat tyres use a strong side wall material that supports the car even if there is no air in one or more of the tyres. This makes it possible to get where we are going even if a tyre is punctured and deflated. Run flat tyres are constructed using alternating layers of heat resistant cord and rubber and usually crescent “shaped wedges of weight- supporting material, strengthening the sidewalls to prevent them from folding over when there is no air pressure.
Self-inflating tyres, on the other hand, are designed to constantly maintain tyre pressure at the proper level. Self-inflating systems are designed more for the slow leaks and for optimizing performance and safety than for keeping a vehicle moving on a tyre that will no longer hold air. Self-inflating tyres allow a vehicle to adjust to the current terrain for ideal performance and safety in those conditions
Currently, lots of consumer vehicles are equipped with pressure-monitoring systems, but there's no way for the driver to do anything about it without an external air source. There are lots of self-inflating-tire systems on the market, but most of them are only available for commercial and military application
Submitted by:
JAYDEEP SINH VAGHELA & SNEHAL PARMAR
PERMANENT ADD:-
MATRUCHHAYA D/118, SUBODHNAGAR,
BHD. DIGJAM MILL, NEAR GANESH HALL,
AIR FORCE ROAD, MANJALPUR,
BHAKTINAGAR, BARODA- 390011
JAMNAGAR.
TIRE-INFLATION BASICS
About 80 percent of the cars on the road are driving with one or more tyres under inflated (as per AAA). Tires lose air through normal driving (especially after hitting pot holes or curbs), permeation and seasonal changes in temperature. Tyres lose one or two psi (pounds per square inch) each month in the winter and even more in the summer. It cannot be told that tyres are properly inflated or not by looking at them. Tyre pressure gauge is used for this. Not only is under inflation bad for tyres, but it's also bad for gas mileage, also affects the way car handles and is generally unsafe.
When tyres are under inflated, the tread wears more quickly. This equates to 15 percent fewer miles which can be drived on them for every 20 percent that they're under inflated. Under inflated tires also overheat more quickly than properly inflated tires, which cause more tire damage.
As tyres are flexible, they flatten at the bottom when they roll. This contact patch rebounds to its original shape once it is no longer in contact with the ground. This rebound creates a wave of motion along with some friction. When there is less air in the tire, that wave is larger and the friction created is greater -- and friction creates heat. If enough heat is generated, the rubber that holds the tire's cords together begin to melt and the tyre fails. Extra resistance of an under inflated tire while rolling makes carâ„¢s engine to work harder. .AAA statistics show that tires that are under inflated by as little as 2 psi reduce fuel efficiency by 10 percent
SELF-INFLATING SYSTEMS
Tire-inflation systems have three general goals:
¢ Detect when the air pressure in a particular tire has dropped - This means they have to constantly (or intermittently) monitor the air pressure in each tire.
¢ Notify the driver of the problem
¢ Inflate that tire back to the proper level - This means there has to be an air supply as well as a check valve that opens only when needed.
PARTS OF ANY SELF-INFLATING SYSTEM
While the available tire inflation systems vary in design, they share some common elements.
¢ They all use some type of valve to isolate individual tires to prevent airflow from all tires when one is being checked or inflated.
¢ They have a method for sensing the tire pressures. This is addressed in most cases with central sensors that relay information to an electronic control unit and then to the driver.
¢ They have an air source, which is usually an existing onboard source such as braking or pneumatic systems. When using an existing system, however, they have to ensure that they don't jeopardize its original function. For this reason, there are safety checks to ensure that there is enough air pressure for the source's primary use before pulling air for tire inflation.
¢ There has to be a way to get the air from the air source to the tires, which is usually through the axle. Systems either use a sealed-hub axle with a hose from the hub to the tire valve or else they run tubes through the axle with the axle acting as a conduit.
¢ There has to be a pressure relief vent to vent air from the tire without risking damage to the hub or rear-axle seals.
CENTRAL TIRE INFLATION SYSTEM (CTIS)
CTIS is provided to control the air pressure in each tyre as a way to improve performance on different surfaces. For example, lowering the air pressure in a tire creates a larger area of contact between the tire and the ground and makes driving on softer ground much easier. It also does less damage to the surface. This is important on work sites and in agricultural fields. By giving the driver direct control over the air pressure in each tire, maneuverability is greatly improved.
Another function of the CTIS is to maintain pressure in the tires if there is a slow leak or puncture. In this case, the system controls inflation automatically based on the selected pressure the driver has set.
CTIS: INSIDE
Here is a look at the overall system:
A wheel valve is located at each wheel end. For dual wheels, the valves are typically connected only to the outer wheel so the pressure between the two tires can be balanced. Part of the wheel valve's job is to isolate the tire from the system when it's not in use in order to let the pressure off of the seal and extend its life. The wheel valve also enables on-demand inflation and deflation of the tires.
An electronic control unit (ECU) mounted behind the passenger seat is the brain of the system. It processes driver commands, monitors all signals throughout the system and tells the system to check tire pressures every 10 minutes to make sure the selected pressure is being maintained. The ECU sends commands to the pneumatic control unit, which directly controls the wheel valves and air system. The pneumatic control unit also contains a sensor that transmits tire-pressure readings to the ECU.
An operator control panel allows the driver to select tire-pressure modes to match current conditions. This dash-mounted panel displays current tire pressures, selected modes and system status. When the driver selects a tyre-pressure setting, signals from the control panel travel to the electronic control unit to the pneumatic control unit to the wheel valves.
When vehicles are moving faster (like on a highway), tire pressure should be higher to prevent tyre damage. The CTIS includes a speed sensor that sends vehicle speed information to the electronic control unit. If the vehicle continues moving at a higher speed for a set period of time, the system automatically inflates the tires to an appropriate pressure for that speed.
This type of system uses air from the same compressor that supplies air to the brakes. A pressure switch makes sure the brake system gets priority, preventing the CTIS from taking air from the supply tank until the brake system is fully charged.
A CLOSER LOOK
On the road: The electronic control unit tells the pneumatic control unit to check current pressure and either inflate or deflate the tire to the pressure selected by the driver. If the system determines that inflation is needed, it first checks to make sure that brake pressure reserves are where they should be; if they are, it applies a slight pressure to the wheel valve to allow inflation. If the tyres are over inflated, the system applies a slight vacuum to the wheel valve. When the pneumatic control unit reads that the appropriate pressure is reached, the valve closes
Hummer self-inflating tire system: At the wheel
The pathway that the air travels for inflation or deflation once it gets to the wheel. The tubing runs from the vehicle's air compressor through the wheel hub and then to the tire valve. The "quick disconnect fitting" allows the tire to be separated from the CTIS system for removal or
servicing. (This diagram also shows the Hummer's run-flat feature, which allows the tyre to continue supporting the vehicle even when it will not hold any air.)
Tire Maintenance System (TMS)
Tire Maintenance System is a "smart" system for tractor trailers that monitors tire pressure and inflates tires as necessary to keep pressure at the right level. It uses air from the trailer's brake supply tank to inflate the tires.
The system has three main components:
¢ The tire hose assembly provides the air route to inflate the tire and has check valves so that the air lines and seals do not have to be pressurized when the system is not checking or inflating the tires. This cuts down on wear and tear on the seals.
¢ The rotary joint is comprised of air and oil seals and bearings and connects the air hose from the non-rotating axle to the rotating hubcap. Its air seals prevent leakage,
and the oil seal prevents contamination. The rotary hub also has a vent to release air pressure in the hubcap.
¢ The manifold houses the pressure protection valve, which makes sure the system doesn't pull air if the brakes' air supply is below 80 psi. It also houses an inlet filter to keep the air clean, a pressure sensor to measure tire pressures and solenoids that control airflow to the tires.
Like the CTIS, this system also has an electronic control unit that runs the entire system. It performs checks to make sure the system is operational, notifies the driver via a warning light on the trailer (visible through the rear-view mirror) if a tyre's pressure drops more than 10 percent below its normal pressure and performs system diagnostics.
The system performs an initial pressure check and adds air to any tire that needs it. The check valves in each tire hose ensure that the other tires don't lose pressure while one tire is being inflated. After an initial pressure check, the system depressurizes to relieve pressure from the seals. Every 10 minutes, the system pressurizes the lines and rechecks tire pressures.
The system measures tire pressure using a series of air pulses in the air lines. If the target pressure in the line is not reached after a certain amount of time, the system begins inflating the tyre(s) until the correct pressure is reached.
AIRGO SYSTEM
The AIRGO system is a constant monitoring system that uses a series of check valves to detect a loss in air pressure.
Unlike some of the other systems, AIRGO doesn't use air from the vehicle's braking system. When air seepage has occurred at any of various points in the system (1), the system draws air (2) from the vehicle's pneumatic system (not shown) and sends it by way of the vehicle's axles (3) -- through the axles themselves if they're pressurized or by way of tubing if they're not -- through the hubcap assembly (4) and into the tire requiring inflation.
A warning light, located on the trailer but visible through the driver's rearview mirror, illuminates when the system has inflated a tire.
Since this is a constant monitoring system, which puts a lot of wear and tear on the seals, AIRGO uses carbon-graphite and case-hardened steel for its seals rather than rubber.
Meritor Tire Inflation System (MTIS)
The MTIS is designed for use on tractor trailers. It uses compressed air from the trailer to inflate any tire that falls below its appropriate pressure. Air from the existing trailer air supply is routed to a control box and then into each axle.
The air lines run through the axles to carry air through a rotary union assembly at the spindle end in order to distribute air to each tire. If there is significant air-pressure loss, an indicator light informs the driver.
The overall system is made up of a wheel-end assembly and a control module.
Wheel-end assembly
The wheel-end assembly includes a flexible hose with check valves. The check valves only allow air to flow into each tyre; this ensures that while one tire is being inflated, the other tyres don't lose air pressure.
Wheel-end assembly
This assembly also incorporates a stator (a non-rotating part) inside the axle spindle and a flow-through tee that is attached to the hubcap. The flow-through tee has a dynamic seal to allow rotation while preventing pressure loss when pressurized air passes from the axle to the hub, which occurs through a tube that runs from the stator into the tee.
In the hubcap assembly, there is a vent to make sure pressure does not build up in the wheel end. A deflector shield keeps contaminants such as dirt and water from entering the wheel end.
For axles with hollow spindles, a press plug seals the pressurized axle interior from the wheel end in order to secure the stator.
Controls
The system control module has a shut-off valve to stop air from being sent to the system, as well as a filter to remove moisture and contaminants. The petcock releases system pressure so maintenance can be performed. Like some of the other systems that use onboard air supplies, this system has a pressure protection valve so that it won't pull air if the air supply is below 80 psi.
Control system
A system pressure adjustment knob allows for adjustments to the overall system air pressure. A flow-sensing switch activates the indicator light to let the driver knows if a significant amount of air is being pumped into a tire, which would indicate a potential puncture.
THE FUTURE OF SELF-INFLATING TYRES
There is a development of an active pressure-management system called TIPM (Tyre Intelligent Pressure Management), due to be available sometime. This system has a compressor that automatically adjusts the pressure in each tire while the vehicle is in operation to compensate for leaks and slow-leak punctures. The driver will be able to adjust the pressure depending on the desired driving mode: comfort, sporty, all-terrain or over-obstacle.
There are at least two other systems in the early development stages that are oriented toward the consumer market -- the Entire system and the Cycloid Air Pump system.
The Entire Self-inflating Tyre system uses a valve that pulls in air from the atmosphere. It then pumps the air into the under-inflated tire using a peristaltic-pump action. The goal is to constantly maintain a specific pressure.
The Entire system is based on this type of peristaltic pump mechanism.
The Auto Pump tire-inflator system by Cycloid has a small, wheel-hub-mounted pump that is powered by the turning of the wheels. When the system's monitor detects a drop in pressure of 2 to 3 psi, it pumps air into the under inflated tire. Auto Pump has a warning system that is activated when there is a puncture.
The computer senses rotation using a rotation sensor on each wheel. If the computer were programmed correctly and if there were a light on the dashboard, then the computer could detect a flat tire. What the computer could do is look at different rotational speeds for one out of the four wheels. A flat tire would spin faster than a properly inflated tire, so the computer would look for one tire spinning faster than the other three, on average, over the course of a period of time. Then it could warn the driver by activating the light on the dash.
