18-11-2014, 08:44 PM
Flange couplings DIN 116
Flanged couplings of torsional rigidity, in particular,
Durable and reliable shaft connections which can
withstand the shocks and radially or axially acting loads.
The connected shafts must be precisely aligned.
Form C are equipped with flanged connections
deepening for axial washers in accordance with
DIN 28135. (used, for example, the vertical
agitator shafts). Thrust thrust washers not
in the scope of delivery and must be ordered separately.
connection dimensions flange couplings
in accordance with DIN 116, centering
connecting parts is achieved, however, only
means fitting bolts. Normal design with feather
keyway according to DIN 6885/1. key Groove
According to DIN 6886 or DIN 6887 on request.
In the case of compounds with different shaft
shaft diameters of clutch size assigned to the
Max diameter of the shaft is used (reduction of the clutch).
> Horizontal: form
> Vertical layout: form C
> Material: Normal design EN-GJL in accordance with
DIN EN 1561. On demand in steel up to size
100 and cast steel with a size of 110
Connection DIN 115 clamp
Clamp couplings high stiffness torsion and reliable
Fittings that can withstand shocks and
radially or axially acting loads connected.
shafts must be precisely aligned. With two
the shells, which are fastened joints are
very easy to install and is
suitable for shafts connected in series
(e. g. Transmission shafts). When connecting shafts
with different diameters we recommend
the thick end of the shaft will be compensated from the diameter
the thinner one. If this is not possible, model
with the shift, the hole larger shaft
The diameter is used (form b). Clamp couplings can
also comes with a protective cover sheet
steel (form AS; BS or CS). Clamping couplings have
the key Groove according to DIN 6885/1.
> Horizontal layout:
After all form the same shaft diameter
Form B for shaft ends with different diameters
> Vertical layout:
Form with the suspension in accordance
DIN 28134
Form C with ring inserts in accordance with DIN 115
Sheet 2
> Material: Normal design EN-GJL in accordance with
DIN EN 1561. GS-45 on request
Flanged couplings of torsional rigidity, in particular,
Durable and reliable shaft connections which can
withstand the shocks and radially or axially acting loads.
The connected shafts must be precisely aligned.
Form C are equipped with flanged connections
deepening for axial washers in accordance with
DIN 28135. (used, for example, the vertical
agitator shafts). Thrust thrust washers not
in the scope of delivery and must be ordered separately.
connection dimensions flange couplings
in accordance with DIN 116, centering
connecting parts is achieved, however, only
means fitting bolts. Normal design with feather
keyway according to DIN 6885/1. key Groove
According to DIN 6886 or DIN 6887 on request.
In the case of compounds with different shaft
shaft diameters of clutch size assigned to the
Max diameter of the shaft is used (reduction of the clutch).
> Horizontal: form
> Vertical layout: form C
> Material: Normal design EN-GJL in accordance with
DIN EN 1561. On demand in steel up to size
100 and cast steel with a size of 110
Connection DIN 115 clamp
Clamp couplings high stiffness torsion and reliable
Fittings that can withstand shocks and
radially or axially acting loads connected.
shafts must be precisely aligned. With two
the shells, which are fastened joints are
very easy to install and is
suitable for shafts connected in series
(e. g. Transmission shafts). When connecting shafts
with different diameters we recommend
the thick end of the shaft will be compensated from the diameter
the thinner one. If this is not possible, model
with the shift, the hole larger shaft
The diameter is used (form b). Clamp couplings can
also comes with a protective cover sheet
steel (form AS; BS or CS). Clamping couplings have
the key Groove according to DIN 6885/1.
> Horizontal layout:
After all form the same shaft diameter
Form B for shaft ends with different diameters
> Vertical layout:
Form with the suspension in accordance
DIN 28134
Form C with ring inserts in accordance with DIN 115
Sheet 2
> Material: Normal design EN-GJL in accordance with
DIN EN 1561. GS-45 on request
