27-04-2017, 12:41 PM
SURVEYOR GR II - SR FOR SCST - SURVEY AND LAND RECORDS.pdf (Size: 1.25 MB / Downloads: 0)
1.A rectilinear figure bounded by more than five sides :
(A)Trapezium(B)Polygons
(C )Rhombus(D)Quadrilateral
2.A line 135 m long represents 22.5 on plan, then R.F is
(A)1/100(B)1/200
(C )1/300(D)1/600
3.As per Indian standard, the length of one link in 30 meter chain is :
(A)30 cm(B)20 cm
(C )40 cm(D)10 cm
4.Limit of areas at which the survey is treated as plain is :
(A)100 KM2(B)150KM2
(C )200 KM2(D)260KM2
5.The total number of zeros graduated on surveyor’s compass is :
(A) One(B) Two
(C ) Three(D) Four
6.If the whole circle bearing of a line is 250°, its reduced bearing is :
(A) N 70° W(B) S 70° W
(C ) S70°E(D) N 70o E
7.In plane table survey measuring of lines and angles is mostly dispensed, but they are obtained :
(A) Graphically (C ) By calculations
(B)By trigonometrically
(D)All the above
8. The alidade used in plane table survey, its beveled edges is also known as :
(A) Ruling edge(B)Working edgeWorking edge
(C ) Fiducial edge(D)All the aboveAll the above
9.Scale of chord is used to measure:
(A) Angles(B)Area
(C ) Length(D)Diameter
10.A King post truss consists of two longer inclined member known as :
(A) Struts(B) Principal rafter
(C ) King post(D) Beam
11.Survey conducted for unearthing relics of antiquity :
(A) Geological survey(B)
(C ) Military survey(D)
Mine survey Archeological survey
12.The maximum value of measurement in quadrilateral bearing is:
(A)0°(B)360°
(C )90c(D)180°
13.Lines passing through points having same declination at a given point is:
(A)Isogonic line(B)Agonicline
(C )Bearing of line(D)Contour line
14.------------ is done to set the plane table in meridian at successive station.
(A)Centering(B)Leveling
(C )Orientation(D)Both (A) and (B)
15.To locate an electric pole near the plane table station :
(A)Intersection(B)Radiation
(C )Traversing(D)Offsetting
16.The method used for locating station points only by sighting towards well defined objects
(A)Intersection(B)Radiation
(C )Traversing(D)Resection
17.Leveling is the art of finding the
(A) Relative heights and depths (C ) Distance
18.Reduced level is also known as :
(A) Datum
(C ) Elevation of the point
of the objects on the surface of the earth.
(B)Relative angles (D) Depth only
(B) Bench mark (D) Change point
19.The error is leveling operation during settlement of tripod on turning point is :
(A) Instrumental error(B) Natural
(C )Personal(D) All the above
20.The staff reading on a certain peg is 1.680 when the staff is held 0.26 m out of the plumb in its total length of 4 m. The correct reading for the staff held vertical is :-
(A) 1.80 m(B) 1.780 m
(C )1.670 m(D) 1.676 m
21.In rise and fall method of reduction of levels provides a check on :
(A)Back sight only(B)Fore sight only
(C )Intermediate sight only(D)All the sightsAll the sights
22.Crop period is the time elapsed between : (A) First watering to last watering (C ) Last watering before harvesting
(B) First watering before sowing (D) Sowing to harvesting
23.For a closed traverse the algebraic sum of the deflection angle is equal to :
(A)90°(B)180°
(C ) 270°' (D) 360°
24.The constant vertical distance between two consecutive contours is called :
(A)Horizontal equivalent(B)Rise
(C )Level difference(D)Contour interval
25.In Theodolite traversing method consists in measuring the several angles successively and finally closing the horizon at the starting point:
(A) Repetition method(B) Reiteration method
(C ) Ordinary method(D) Direct method
26.The vertical circle of the instrument is on the left of the observer while taking a reading, the position is called:
(A)Face right observation(B)Face left observation
(C )Normal position(D)Both (B) and (C )
27.The functional 1 key for ortho command used in CAD :
(A)Fe(B)F6
(C )F7(D)F8
28.The CAD command used to lengthen or shorten the lines or object is :
(A)Stretch(B)Extend
(C )Offset(D)Distance
29.The drafting setting used to pick a geometric point on an object is :
(A)SNAP(B)O-SNAP
(C )ORTHO(D)POLAR TRACKING
30.The CAD command used to join 2 parallel line is :
(A) Chamfer(B) Extend
'(C ) Fillet(D) Stretch
31.In a well conditioned triangle, no angle should be less than :
(A)30°(B)40°
(C )50°(D)60°
32.Number of arrows accompanying each chain :
(A)12'(B)10
(C )8(D)6
38. In one setting up of the level the maximum number of back Bight and fore sight is :
(A)One and two(B) Two each
(C ) One each(D) Two and one
34.In Leveling station is a point where :
(A) Staff is held (C ) Ranging rod is fixed
(B) Instrument is fixed (D) Peg is marked
35.Contour map is used for:
(A) Inter visibility between ground points (B) Quantities of earth work (C ) Tracing route(D) All the above
36.Plunging or reversing of the theodolite telescope is also called :
(A) Swinging(B) Translating
(C ) Change the face(D) None of these
37.The type of bond employed in brick work consist of alternate courses of headers and stretchers:
(A) English(B)FlemishFlemish
(C ) Dutch(D)HeadingHeading
38.Agate cap is fitted with a :
(A) Cross staff(B)LevelLevel
(C ) Chain(D)Prismatic compassPrismatic compass
39.The closing error in a closed traverse is adjustedby:
(A) Lehmann's rule(B). Trapezoidal rule
(C ) Bowditch's rule(D)Simpson's rule
40.For ranging a line number of ranging rod required is :
(A) atleast 3(B)atleast 4
(C ) atleast 5(D)atleast 2
41.Curvature effect of the earth is taken into account in :
(A) Geodetic survey(B)Plane surveyPlane survey
(C ) Plane table survey(D)Hydrographic surveyHydrographic survey
42. The T- square is used for drawing :
(A) Vertical(B)Horizontal
(C ) Inclined(D)CurveCurve
43.To prevent warping of the board are cleared at its back.
(A) Packing(B)Wooden block
(C ) Battens(D)Blades
44.The first dimension line should be placed atleast:
(A) 10 mm from the construction line(B)12 mm from the construction line
(C ) 8 mm from the construction line(D)9 mm from the constraction line9 mm from the construction line
45.The sum of the included angle of a hexagon is :
(A) 720°(B)540°
(C ) 900°(D)360o360°
46.The angle of inclined letters :•
(A) 30°(B)60o60°
(C ) 45°(D)75o
47.The standard size of B2 imperial drawing is :
(A) 700 x 600(B)800x600800 x 600
(C ) 800 x 500(D)700x500
48.The lowest part of the structure which transmit the load to the soil is :
(A) Superstructure(B)Basement
(C ) Plinth(D)SubstructureSubstructure
49.Area of trimmed Ao sheet designated by ISO is :
(A) 1 m2(B)0.5 m2
(C ) 0.25 m2(D)0.125 m2
50.A right angled parallelogram with its opposite sides are equal:
(A) Pentagon(B)TriangleTriangle
(C ) Rectangle(D)TrapeziumTrapezium
51. Number of bricks required for one cubic meter :
(A)600(B)900
(C )800800(D)600
52.A lintel is provided :
(A)Over a door opening(B)Below a door opening
(C )Inner a door opening(D)Side a door openingSide a door opening
53.The Diameter of the graduated circle on the lower plate determines the :
(A)Size of theodolite(B)Length of theodoliteLength of theodolite
(C )Thickness of theodolite(D)Accuracy of theodolite
54.In Theodolite the verniers A and B arc marked in :
(A)Upper plate(B)Lower plate
(C )Vertical plateVertical plate(D)Graduated circleGraduated circle
55.Pantograph is used for :
(A)Measuring right angles(B)Enlarging and reducing plans
(C )Measuring distancesMeasuring distances(D)Measuring volumeMeasuring volume
56.Simplify:44 - [33 - {44(33 - 44 - 33)}].
(A)11(B)1925
(C )-11(D)3333
57.Factorize: 49*’-81/ =
(A) A(B)(7jt + 9y)(7x-9y)
(C )(7x + 9y)(7jc + 9>)(D)(7x + 6y)(7x-9y)
58.Volume of a sphere is given by :
(A)4 3 — nr 3(B)3- — nл 4
(C )4 3 ^(D)4 2 -лr2 3
59.Volume of a cylinder is given by :
(A)лrA(B)лr2
(C ) лr'h(D)лdh
60.The equation of a straight line in a graph is shown by :
(A) y - mx(B)y=mx
(C ) y=mx(D)y = mx3
61.The volume of a cube with each side measures 2 m is :
(A) 4 m2(B)8 m2
(C ) 4 m3(D)8 m3
62.The value of sine 90° is:
(A) 1(B)0
(C ) 5(D)l/V2
63.The value of 1 + tan θ is :
(A) cosec2 θ(B)sec2 θ
(C ) cotθ.(D)sec 6
64.The value of sin 2A :
(A) 1-sin A(B)1-cos2 A
(C ) 2sin A/cos A(D)2sin A cosA
65.One chain is:
(A) 22 yards(B)11 yards
(C ) 27 yards(D)10 yards10 yards
66.The base unit of length in S.l system :
(A) Yards(B)MeterMeter
(C ) Feet(D)Inch
67.The multiple factor of the prefix deci is :
(A) 0.1(B)0.01
(C ) 0.01(D)0.001
68.The rate at which work is done:
(A) Energy(B)Force
(C ) Power(D)Work
69. The unit of velocity is :
(A)Rate of change of position of 1 m per second
(B)Rate of change of one radian per second
(C )One radian per second
(D)Watt
70. A combination of two reverse curve used to avoid intervening obstructions like buildings etc :
(A) Simple curve(B)Compound
(C ) Reverse •(D)Deviation
71.A quantity having both magnitude and direction is :
(A) Scalar(B)Scale
(C ) Vector(D)Co-ordinate
72.The eccentricity of a parabola is usually :
(A) >1(B)<1
(C ) 1(D)=1
73.The value of "g"(acceleration due to gravity) is :
(A) 9.8 m/sa(B)8.9 m/s2
(C ) 9.6 m/sa(D)98 m/s2
74.The change in dimension per unit dimension of a body is called :
(A) Stress(B)Strain
A(C ) Tension . 11(D)PlasticityPlasticity
75. Hook's law holds upto :
(A) Yield point(B)Elastic limit
(C ) Plastic limit(D)Breaking point
76.Solder is an alloy of:
(A) Alumina and lead(B)Alumina and tin
(C ) Copper and Zinc(D)Lead and tin
77.An optical instrument used in modern surveying, archaeology, investigation and for military service etc.:
(A) Theodolite(B)Total • station
(C ) Dumpy level(D)Prismatic compass
78.An triangle is obtain by joining the pole, zenith and circle is:any star on the sphere by arc of great
(A) Spherical triangle(B)Celestial triangle
(C ) Astronomical triangle(D)Terrestrial triangle
79.The science and art of collecting information about objects, area or phenomena from distance without being in physical contact with them :
(A) Remote sensing(B)Surveying
(C ) Hydrographic survey(D)Contouring
80.The reverse process of surveying in with the data are transferred from drawing to the ground :
(A) Ranging(B)Chaining
(C ) Both (A) and (B)(D)Setting out
81.'Tatwa Prakasika Ashram' was started by ;•
(A) Vagbhatananda(B)Chattampi Swamikal
(C ) Kumaraguru(D)V.T. Bhattatirippad
82.The device, that measures the depth of the sea :
(A) Barometer(B)Fathometer
(C ) Manometer(D)Lactometer
83. ‘The Darsanamala', famous work of Sree Narayana Guru, was written in language.
(A) Prakrith (C ) Sanskrit
(B)Cornwallis (D) William Bentinck
84.The Practice of 'Sati' was banned by :
(A)Dalhousie (C ) Rippon
(B)Tamil (D) Pali
85.Ezhuthachan Award Winner of 2014 :
(A)Vishnu Narayanan Namboothiri (C ) Dr. M.K. Sanu
(B)Attoor Ravi Varma (D) P. Narayana Kuruppu
86.Who was the author of ‘Anandakkummi’?
(A)Pandit K.P. Karuppan (C ) Ayya Vaikundar
(B)Brahmananda Swami Sivayogi (D) Thycaud Ayya
87.The Partition of Bengal' was revoked in :
(A)1905
(C )1911
(B)1909
(D)1907
88.Who directed the film ‘Kuttisrank’?
(A)Salim Ahammed (C ) Adoor Gopalakrishnan
(B)M.T. Vasudevan Nair (D) Shaji N. Karun
89.The editor of ‘Yuktivadi Magazine’:
(A)K. Ayyappan (C ) Vakkom Moulavi
(B)C. Krishnan
(D) Swadesabhimani Ramakrishna Piliai
90.‘Durand Cup associated with :
(A)Cricket (C ) Polo
(B)Foot ball (D) Weight lifting
91.One of the Nobel Prize winner of Chemistry in 2014 :
(A)Jean Tirole(B) Hiroshi Amano
(C )Eric Betzig(D) Patrick Modiano
92.Who was the author of the work ‘Lanka Mardhanam?
(A) Pandit K.P. Karuppan(B) Kumaranasan
(C )Mannathu Padmanabhan(D) Poikayil Yohannan
93.The renaming of Planning commission called ‘NITI Aayog was formed on :
(A)8th February 2015(B)1st January2015
(C )11th January 2015(D)8th December 2014
94.‘Saptanga Theory’ of state was associated with :
(A)Aristotle(B)Patanjali
(C )Megasthanese(D)Kautilya
95.The first Kerala State Political Conference was held on 23rd April 1921 at Ottappalam under the Presidentship of:
(A) K. Madhavan Nair
(C )Annie Besant
(B)T.Prakasam
(D)K.P. Kesava Menon
96.The head quarters of UNICEF :
(A) Newyork
(C )Paris
(B) Washington
(D)Geneva
97.‘Blue Revolution' aims for increasing — cultivation. .
(A) Milk (C ) Fish
(B) Fruits
(D)Cotton
98.The Pictures carved at Edakkal caves in Wayanad noticed by time.
(A) Alexander Cunningham
(C )John Marshall
(B) B.K. Thaper (D) Faucett
for the first
99.The Government of India appointed the 'Hunter Committee’ to investigate into and report on :
(A) Wagon Tragedy(B) Education Committee
(C )Jallianwalla Bagh Massacre(D) Famine Commission
100.‘Melmundu kalapam’ was started by — community.
(A) Pulaya
(C )Ezhava
(B) Kurichya
(D)Channar