ASK HERE

15-11-2017, 05:37 PM

I want project report on solar tracker by using lM358 ic

jaseela123d · 16-11-2017, 09:23 AM

The amount of energy converted depends on the amount of light that falls on the Panel. Generally, solar panels are fixed devices that are fixed in one position. The electrical energy produced can be increased if we move the solar panel as the movement of the sun. Here is a simple low-cost solar circuit that automatically moves the solar panel in the direction of the sun. The movement of the Sun is detected using two LDRs that are arranged in the Solar Panel in such a way that the intensity of the falling light varies as the direction of the Sun changes.

Circuit diagram

Working

The heart of the circuit above is two voltage comparators made using LM358 Dual Op-Amp. We all know that when the intensity of light falling on an LDR increases, its resistance decreases. Here LDR is connected to a series resistor (R3 and R4), therefore, when the intensity of the light falling on an LDR increases, the voltage across the corresponding resistance (R3 or R4) increases.

The output of the voltage comparator will be high when the voltage in the non-inverting terminal (+) is greater than the voltage in the inverter terminal (-). The reversing terminals (-) of both comparators are short-circuited and connected to a variable resistor (RV1), which is used to establish the reference voltage. Therefore, the sensitivity of both LDR can be adjusted by varying the 10K potentiometer shown on the left side of the circuit diagram. When the light falls, an LDR increases, the voltage at the non-inverting terminal (+) of the corresponding comparator increases and its output rises HIGH.

[Image: Solar-Tracker-Various-Modes.jpg]

The direction of motor rotation is controlled by the H-Bridge formed by the complementary symmetry transistors BC547 and BC557. Consider the case when the output of the first comparator (U1: A) is high and the output of the second comparator (U1: B) is low. In this case, transistors Q1 and Q4 will turn on and the resulting current will turn the motor clockwise. Consider the case when the output of the first comparator is low and the output of the second comparator is high. In this case, transistors Q2 and Q3 will turn on and the resulting current will rotate the motor counterclockwise. If the output of both comparators is low, transistors Q3 and Q4 turn on, but no current will flow through the motor. Similarly, if the output of both comparators is high, transistors Q1 and Q2 turn on, but no current will flow through the motor.

The DC motor must be connected to the panel in such a way that the rotation of the motor turns the panel in the direction of the sun's movement.

Possibly Related Threads...
Thread		Author	Replies	Views	Last Post
	slide share ppt of artifical hand using embedded system		0	1,290	24-10-2018, 02:26 PM Last Post: Guest
	passive solar buildings seminar report		0	1,324	14-10-2018, 12:41 PM Last Post: Guest
	project on door lock system using 8085 microcontroller		0	754	04-10-2018, 10:39 PM Last Post: Guest
	census management system using vb net		0	922	30-09-2018, 05:03 AM Last Post: Guest
	solar refrigeration system seminar report pdf		0	740	26-09-2018, 07:49 PM Last Post: Guest
	solar tracking system project report doc		0	1,992	25-09-2018, 10:51 AM Last Post: Guest
	veenus courier tracking		0	480	20-08-2018, 07:56 PM Last Post: Guest
	bpo management system using uml diagrams		0	604	29-07-2018, 05:23 PM Last Post: Guest
	hostel management system in c language using linked list		0	925	16-07-2018, 09:58 AM Last Post: Guest
	traffic light control system using 8086 code		0	831	12-07-2018, 09:46 AM Last Post: Guest

Important Note..!

ASK HERE