PCM PRINCIPLES&CAS,CCS#7-TRAINING PROJECT REPORT AT ALTTC GHAZIABAD(BSNL)
[attachment=15906]

Pulse Code Modulation (PCM)
Principles
Analog transmission is not particularly efficient. When the signal-to-noise ratio of an analog signal deteriorates due to attenuation, amplifying the signal also amplifies noise. Digital signals are more easily separated from noise and can be regenerated in their original state. The conversion of analogue signals to digital signals therefore eliminates the problems caused by attenuation. Pulse Code Modulation (PCM) is the simplest form of waveform coding. Waveform coding is used to encode analogue signals (for example speech) into a digital signal. The digital signal is subsequently used to reconstruct the analogue signal. The accuracy with which the analogue signal can be reproduced depends in part on the number of bits used to encode the original signal. Pulse code modulation is an extension of Pulse Amplitude Modulation (PAM), in which a sampled signal consists of a train of pulses where each pulse corresponds to the amplitude of the signal at the corresponding sampling time (the signal is modulated in amplitude). Each analogue sample value is quantised into a discrete value for representation as a digital code word. Pulse code modulation is the most frequently used analogue-to-digital conversion technique, and is defined in the ITU-T G.711 specification. The main parts of a conversion system are the encoder (the analogue-to-digital converter) and the decoder (the digital-to-analogue converter). The combined encoder/decoder is known as a codec. A PCM encoder performs three functions:
• sampling
• quantising
• encoding
The human voice uses frequencies between 100Hz and 10,000Hz, but it has been found that most of the energy in speech is between 300 Hertz and 3400 Hertz - a bandwidth of approximately 3100 Hertz. Before converting the signal from analog to digital, the unwanted frequency components of the signal are filtered out. This makes the task of converting the signal to digital form much easier, and results in an acceptable quality of signal reproduction for voice communication. From an equipment point of viev, because the manufacture of very precise filters would be expensive, a bandwidth of 4000 Hertz is generally used. This bandwidth limitation also helps to reduce aliasing - aliasing happens when the number of samples is insufficient to adequately represent the analog waveform (the same effect you can see on a computer screen when diagonal and curved lines are displayed as a series of zigzag horizontal and vertical lines).

Sampling


Sampling the analogue signal

Sampling is the process of reading the values of the filtered analogue signal at discrete time intervals (i.e. at a constant sampling frequency, called the sampling frequency). A scientist called Harry Nyquist discovered that the original analogue signal could be reconstructed if enough samples were taken. He found that if the sampling frequency is at least twice the highest frequency of the input analogue signal, the signal could be reconstructed using a low-pass filter at the destination.

Quantisation
Quantisation is the process of assigning a discrete value from a range of possible values to each sample obtained. The number of possible values will depend on the number of bits used to represent each sample. Quantisation can be achieved by either rounding the signal up or down to the neares available value, or truncating the signal to the nearest value which is lower than the actual sample. The process results in a stepped waveform resembling the source signal. The difference between the sample and the value assigned to it is known as the quantisation noise (or quantisation error).
Quantisation noise can be reduced by increasing the number of quantisation intervals, because the difference between the input signal amplitude and the quantization interval decreases as the number of quantization intervals increases. This would, however, increase the PCM bandwidth. Uniform quantisation uses equal quantisation levels throughout the entire range of an input analogue signal. The signal-to-noise ratio (SNR), including quantisation noise, is the most important factor affecting voice quality in uniform quantisation. The signal-to-noise ratio is measured in decibels (dB). The higher the signal-to-noise ratio, the better the voice quality. Quantisation noise reduces the signal-to-noise ratio of a signal, so an increase in quantisation noise degrades the quality of a voice signal. Low signals will have a small signal-to-noise ratio and high signals will have a large signal-to-noise ratio. Because most voice signals are relatively low, having better voice quality at higher signal levels is an inefficient way of digitising voice signals. Uniform quantisation was therefore replaced by a non-uniform quantisation process called companding (see below).
Narrowband speech is typically sampled 8000 times per second, and each sample must be quantised. If linear quantisation is used, 12 bits per sample are required, giving a bit rate of 96 kbits per second. This can be reduced using non-linear quantisation, in which 8 bits per sample is sufficient to provide speech quality almost indistinguishable from the original. This results in a bit rate of 64 kbits per second. Two non-linear PCM codecs were standardised in the 1960s - µ-law (mu-law) coding was the standard developed in the United States, while A-law compression was used in Europe. These codecs are still widely used today.

Encoding
Encoding is the process of representing the sampled values as a binary number in the range 0 to n. The value of n is chosen as a power of 2, depending on the accuracy required. Increasing n reduces the step size between adjacent quantisation levels and hence reduces the quantisation noise. The down side of this is that the amount of digital data required to represent the analogue signal increases.


Stages in the analogue-to-digital conversion process


Companding
Working with very small signal levels (by comparison with the quantisation interval) can introduce more errors. Companding can be used to increase the accuracy of such signals. This is the process of distorting the analogue signal in a controlled way before quantising takes place, by compressing its larger values at the source and then expanding them at the receiving end. There are two standards used: A-law in Europe, and µ-law in the USA. The term companding was created by combining the termsCOMpressing and exPANDING. Input analog signal samples are compressed into logarithmic segments. Each segment is then quantised, and coded using uniform quantisation. The compression process is logarithmic, where the compression increases as the sample signals increase (the larger sample signals are compressed more than the smaller sample signals, causing the quantization noise to increase as the sample signal increases). A logarithmic increase in quantisation noise throughout the dynamic range of an input sample signal gives a signal-to-noise ratio which is almost constant over a wide range of input levels. A rate of eight bits per sample (64 kbits per second) gives a reconstructed signal which is very close the original. The advantages of this system include low complexity and delay, and high-quality reproduction of speech. The disadvantages are a relatively high bit rate and a high susceptibility to channel errors.
Similarities between A-law and µ-law:
• Both are linear approximations of a logrithmic input/output relationship
• Both are implemented using 8-bit code words (256 levels, one for each quantisation interval). This allows for a bit rate of 64 kbits per second
• Both break the dynamic range into 16 segments (8 positive and 8 negative) - each segment is twice the length of the preceeding one, and uniform quantisation is used within each segment
• Both use similar encoding techniques for the 8-bit word - the first (most significant bit) identifies polarity, bits 2, 3 and 4 identify the segment, and the last four bits identify the quantisation level within the segment
Differences between A-law and µ-law:
• Different linear approximations lead to different lengths and slopes
• Numerical assignment of the bit positions in the 8-bit code word to segments and to quantisation levels within segments are different
• A-law provides a greater dynamic range
• µ-law provides better signal/distortion performance for low level signals
• A-law requires 13 bits for a uniform PCM equivalent, whereas m-law requires 14 bits
• International connections should use A-law (µ to A conversion is the responsibility of the µ-law country)



PCM and Time Division Multiplexing (TDM)
Time division multiplexing is used at local exchanges to combine a number of incoming voice signals onto an outgoing trunk. Each incoming channel is allocated a specific time slot on the outgoing trunk, and has full access to the transmission line only during its particular time slot. Because the incoming signals are analogue, they must first be digitised, because TDM can only handle digital signals. Because PCM samples the incoming signals 8000 times per second, each sample occupies 1/8000 seconds (125 µseconds). PCM is at the heart of the modern telephone system, and consequently, nearly all time intervals used in the telephone system are multiples of 125 µseconds.
Because of a failure to agree on an international standard for digital transmission, the systems used in Europe and North America are different. The North American standard is based on a 24-channel PCM system, wheras the European system is based on 30/32 channels. This system contains 30 speech channels, a synchronisation channel and a signalling channel, and the gross line bit rate of the system is 2.048 Mbps (32 x 64 Kbps). The system can be adapted for common channel signalling, providing 31 data channels and employing a single synchronisation channel. The following details refer to the European system.
The 30/32 channel system uses a frame and multiframe structure, with each frame consisting of 32 pulse channel time slots numbered 0-31. Slot 0 contains the Frame Alignment Word (FAW) and Frame Service Word (FSW). Slots 1-15 and 17-31 are used for digitised speech (channels 1-15 and 16-30 respectively). In each digitised speech channel, the first bit is used to signify the polarity of the sample, and the remaining bits represent the amplitude of the sample. The duration of each bit on a PCM system is 488 nanoseconds (ns). Each time slot is therefore 3.904 µseconds (8 bits x 488 ns). Each frame therefore occupies 125 milliseconds (32 x 3.904 mseconds).