Posts: 3,561
Threads: 923
Joined: Sep 2010
[attachment=5542]
Abstract
Intelligent Energy Saving System can be used in places like where lighting is very important. The libraries will be well illuminated with many lamps. When people are not present at a reading place the lighting can be made OFF and when they are present, the lighting made ON. All these can be done through by Dimming circuit and PIR sensor.
If a person entering to the monitored area, the PIR sensors activates and sense the person, gives to the micro controller. The Infrared energy emitted from the living body is focused by a Fresnel lens segment. Then only the PIR sensor activates. After sensing the person LDR checks the light intensity of the monitored area, whether it is bright or dark. Depending on the LDR output, the lamp may be ON / OFF by using Dimmer circuit.
By using this system we can adjust the speed of Fan according to the room temperature measured by Thermostat, which is connected to the micro controller.
To display the room temperature of PIR mode operation we are using the LCD display.
Introduction
Intelligent Energy Saving System, the aim of the project is to save the energy. In this project we are using various sensors, controlling and display.
However, in this project work the basic signal processing of various parameters which are temperature, LDR, Smoke sensor. For measuring various parameters values, various sensors are used and the output of these sensors are converted to control the parameters. The control circuit is designed using micro-controller. The outputs of all the three parameters are fed to micro-controller. The output of the micro-controller is used to drive the LCD display, so that the value of each parameter can be displayed. In addition to the LCD display micro-controller outputs are also used to driver a relay independently. This relay energizes and de-energizes automatically according to the condition of the parameter.
Posts: 2,300
Threads: 878
Joined: Sep 2010
[attachment=5728]
Intelligent Energy Saving System
INTRODUCTION
Intelligent Energy Saving System, the aim of the project is to save the energy. In this project we are using various sensors, controlling and display.
However, in this project work the basic signal processing of various parameters which are temperature, LDR, Smoke sensor. For measuring various parameters values, various sensors are used and the output of these sensors are converted to control the parameters. The control circuit is designed using micro-controller. The outputs of all the three parameters are fed to micro-controller. The output of the micro-controller is used to drive the LCD display, so that the value of each parameter can be displayed. In addition to the LCD display micro-controller outputs are also used to driver a relay independently. This relay energizes and de-energizes automatically according to the condition of the parameter.
1.1 OBJECTIVE OF THE PROJECT: -
The aim of the project is to save the energy or power, used in places like libraries where lighting is very important for the people who come to read books. So, the libraries will be well illuminated with many lamps.
At the same time when people are not present at a particular reading place the lighting can be made off by using Dimmer and when people come to that area, according to the LDR lighting can be made sufficiently brighter.
Posts: 2,300
Threads: 878
Joined: Sep 2010
[attachment=7140]
Intelligent Energy Saving System
ABSTRACT
This project is proposing the household energy management and warning system for energy saving solution. The overall control scheme is mainly governed by a PIC16F877A microcontroller. There are four subsystems to be concerned (i) air-condition’s inverter control, (ii) lamp brightness control, (iii) power switching control (for general loads such as television, radio, fan, etc.), (iv) house hold electricity usage warning system. This whole system can monitor the power usage and display through a LCD monitor. Then, it can warn the users through LED bulbs when the power usage is getting close to the monthly prescribed energy usage levels. An experiment conducted by installing this system in an apartment room has shown a satisfactory result in reducing power usage level.
Posts: 1
Threads: 0
Joined: Dec 2010
i want the components list to be used for this Intelligent energy saving system..... please reply me....
i need the components list of this project..... pls send immediately
Posts: 3,561
Threads: 923
Joined: Sep 2010
you can find more details from the attached files. so please download them
Posts: 1
Threads: 0
Joined: Feb 2011
Please Help Me With Brief Synopsis
Posts: 1
Threads: 0
Joined: Jul 2011
13-07-2011, 08:00 PM
hi i want this project documentation plzzzzzzzzz send my eail id.
Posts: 6,566
Threads: 1,107
Joined: Jul 2011
Posts: 4
Threads: 0
Joined: Jul 2011
Fantastic Project to help manage energy for future use. Can i have the the full circuit diagram
Posts: 6,566
Threads: 1,107
Joined: Jul 2011
Posts: 2
Threads: 0
Joined: Nov 2011
hi
can i please get the code of this using 8051 microcontroller
thanx in advance
Posts: 6,566
Threads: 1,107
Joined: Jul 2011
to get information about the topic" Intelligent Energy Saving System" refer the page link bellow
http://studentbank.in/report-auditorium-...controller
Posts: 1
Threads: 0
Joined: Jan 2012
technical seminar of intelligent energy saving system
hey can we get the code of intelligent energy system using 8051?
Posts: 7,939
Threads: 421
Joined: Jun 2012
to get information about the topic "Intelligent Energy Saving System" full report ppt AND related topic refer the page link bellow
http://studentbank.in/report-intelligent...ing-system