digital clock using 8051 lcd report pdf
#1

please send me the pdf report of Digital clock using 8051 at the following id

dhimanpawan63[at]yahoo.co.in

Thanx in advance
Reply
#2

A digital clock is one that displays time digitally. The project explained here, displays time on a 16x2 LCD module. The LCD is interfaced with 8051 microcontroller (AT89C51). This circuit can be used in cars, houses, offices etc.

Digital clock displays the time using numbers. This circuit is used in many applications like cars, railway stations, houses, offices, etc. in order to provide accurate time and date. In this type of applications, normally we use RTC (Real Time Clock) ICs to display the time and date accurately. This circuit displays the time on LCD. For this clock, we can set the time at any instant. Here the clock works in 24 hour mode and the RTC chip is configured by programming 8051 controller.

Circuit Principle:

Here 8051 controller continuously reads the data from Real time clock and process it in correct order to display the time on LCD. INT1 of the 8051 controller is used to set the time to the digital clock. If you make P3.3 pin LOW then interrupt arises and set_time function is called to set the time. To set the time to the clock use P1.4 and P1.5 pins. P1.4 is used to vary the hours and P1.5 is used to vary the minutes. After setting the time make P1.6 high to run the clock with the time set by user.

Circuit Components:

8051 microcontroller
Project PCB
Programming cable
DC Battery or 12V, 1A adaptor
DS12C887 RTC IC
16*2 alphanumeric LCD
Push buttons – 4
Slide switches – 3
2 ceramic capacitors – 33pF
12 MHz crystal
Electrolytic capacitor – 10uF, 16V
Resistor (1/4 watt) – 10k
Pot – 10k
5V DC power supply circuit
Single pin connecting wires
Circuit Design:

The circuit shows you how interface RTC IC to the 8051 controller. Port P0 is used as a data port of Real time clock. Port P2 of controller is connected to the data pins of LCD. Pins P1.1, P1.2 and P1.3 of controller are connected to the RS, RW, EN pins respectively. P1.0 is connected to the RESET of RTC. Push buttons are connected to the P1.4 and P1.5. These are used set the time. P1.6 is configured as START pin used to run the clock with time set by the user. P3.3 is connected to the push button used to call the set_time function.

DS12C887 Real Time Clock:

This IC is used most of the applications to provide accurate time and date. This IC provides the time in both 12 hour mode and 24 hour mode. This IC also provides calendar components day, month and year. This RTC uses internal lithium battery to keep the time and date updated when power is failed. This IC has 128 bytes of RAM memory. In these 128 bytes of RAM 14 bytes are used for time, date and registers. Remaining 114 bytes are used to store general purpose data.

The control registers of RTC are accessible only when the power is applied from external source. This IC requires more than 4.25V power supply and the control registers are accessible after 200ms when external power is supplied.

Reply

Important Note..!

If you are not satisfied with above reply ,..Please

ASK HERE

So that we will collect data for you and will made reply to the request....OR try below "QUICK REPLY" box to add a reply to this page
Popular Searches: lcd based digital clock using 89c51, lcd atmega16 digital clock program, project report on lcd interfacing using 8051 pdf, digital alarm clock using 8051 code in c, simple digital clock c code using 8051, slide presentation for digital clock using lcd pdf, lcd based digital alarm clock,

[-]
Quick Reply
Message
Type your reply to this message here.

Image Verification
Please enter the text contained within the image into the text box below it. This process is used to prevent automated spam bots.
Image Verification
(case insensitive)

Possibly Related Threads...
Thread Author Replies Views Last Post
  pdf k53 learners test questions and answers 2015 pdf 2 11,125 18-05-2018, 06:21 PM
Last Post: Guest
Smile download wi vi technology seminars report pdf 2 15,696 24-01-2018, 11:27 PM
Last Post: sultan@123
  auto credit energy metering system using mifare card with pdf 2 1,577 12-09-2017, 05:12 PM
Last Post: Guest
Wink seminar report on pavement design using geotextiles 4 1,297 18-05-2017, 11:08 AM
Last Post: Umeshyuvi
  source code for task scheduling using genetic algorithm using java 2 8,447 11-04-2017, 08:31 PM
Last Post: Guest
  electronic eye controlled security system using ldr pdf 3 8,874 15-02-2017, 12:42 PM
Last Post: jaseela123d
Music automatic differential unit locking system report pdf 4 1,474 15-02-2017, 12:02 PM
Last Post: jaseela123d
  solar powered aircraft seminars report pdf 2 7,810 11-10-2016, 09:36 AM
Last Post: sachinkoli
  pdf seminars report fog computing 1 7,651 09-10-2016, 06:52 PM
Last Post: hiiire
  seminar report regenerative shock absorber pdf 2 952 01-10-2016, 03:40 PM
Last Post: Guest

Forum Jump: